KLING & FREITAG SONA SUB Manual de usuario
K&F SONA SUB
Important Information,
Please Read Before Use!
KLING & FREITAG GmbH
Junkersstraße 14
D-30179 Hannover
TEL +49 (0) 511 96 99 70
FAX +49 (0) 511 67 37 94
www.kling-freitag.de
User's Manual Version 2.1
Released: 25.06.2014
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 3 of 21
Table of contents
1Introduction 4
1.1 Symbols in User's Manual 4
1.2 Information about this User's Manual 4
2Product Description 5
2.1 Scope of Delivery 5
2.2 Overview of Components 5
2.3 Required signal processor 6
2.4 Required mounting material 6
3Safety Instructions 7
3.1 Mounting the Speakers / Wall and Ceiling Installation 7
3.2 Notes for Mounting the Speakers 7
3.3 Preventing hearing damage 7
3.4 Protecting the Speakers / Operating Safety 7
4Wall and Ceiling Installation 9
5Correct Ratio between Top and Bass Speakers 12
5.1 Level increase because of adjacent areas 12
6Configuration and Connecting Diagram 13
6.1 Terminal assignment 13
6.2 Terminal assignment, option "XO" 13
6.3 SONA SUB with 'SONA 5 unfiltered' 14
6.4 SONA SUB with SONA 5 or SONA 6 filtered 14
6.5 SONA SUB "XO" with SONA 5 or SONA 6 15
7Wiring 16
7.1 Wiring instructions 16
8Operating the Speakers 17
9Technical Specifications 18
10 Measuring Diagrams 19
11 Dimensions 20
12 Disposal 21
12.1 Regulations for Disposal 21
12.1.1 Germany 21
12.1.2 EU, Norway, Iceland, and Liechtenstein 21
12.1.3 All other Countries 21
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 4 of 21
1. Introduction
Thank you for your decision to buy a KLING & FREITAG product. To guarantee a trouble-
free operating of the equipment and to allow your KLING & FREITAG SONA SUB system to
achieve its full potential please read the operating instructions carefully before use. With
the purchase of a SONA SUB, you have acquired a large sound system with the highest
possible quality and performance capabilities. As the owner of a SONA SUB loudspeaker, you
now have a versatile and highly professional tool which, when operated properly, is a true
pleasure to use.
1.1 Symbols in User's Manual
Warning
This symbol indicates the possibility of life-threatening danger and a health risk for persons.
Not following these instructions may result in serious health problems including potentially
fatal injuries.
Caution
This symbol indicates a possibly dangerous situation. Not following these instructions may
cause minor injuries or cause property damage.
This symbol gives instructions for the proper use of the described products. Not following
these instructions may cause malfunctions or property damage.
Tip
This symbol indicates notes that help you to handle the described products easier.
1.2 Information about this User's Manual
© KLING & FREITAG GMBH, all rights reserved.
All specifications in this manual are based on information available at the time of publishing
for the features and safety guidelines of the described products.
Technical specifications, measurements, weights and properties are not guaranteed.
The manufacturer reserves the right to make product alterations within legal provisions as
well as changes to improve product quality.
All persons who use the speaker system must have this guide and all further information for
safe operations available to them during assembly, disassembly, and use. The speaker system
may neither be set up nor used until this manual has been read, understood and kept readily
available in site.
We appreciate any input with suggestions and improvements for this manual. Please send this
to us at the following address:
[email protected] or to:
KLING & FREITAG GMBH Junkersstr.14 D-30179 Hannover.
Phone +49 (0) 511 96 99 70, Fax +49 (0) 511 67 37 94.
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 5 of 21
2. Product Description
The subwoofer SONA SUB is the ideal bass supplement for the speaker SONA 5. With its
discreet appearance, it fits in nearly any architecture. The practical mounting points with
a double keyhole design enable wall and ceiling installation. In addition to possible use
with the K&F Controller CD 44, it can also be operated with a universal electronic crossover.
With the option "XO" you can use the SONA SUB without a signal processor too. This
possibilities makes it extremely attractive not only because of its convincing performance but
also economically.
2.1 Scope of Delivery
• A subwoofer for use with the top K&F SONA 5. 3 mounting points based on the keyhole
principle and a fixing hole for horizontal and vertical wall mounting.
• Drilling plan for marking mounting points for wall and ceiling mounting.
• 4-pin Phoenix plug for the corresponding connector in the speaker.
• Plug for fixing hole.
• User's Manual (1x)
2.2 Overview of Components
1
2
3
4
5
6
7
1. Mounting Points in double keyhole design for horizontal and vertical mounting.
2. SPEAKON Connector type NL4 MPR, parallel wiring to Phoenix connector.
3. PHOENIX Connector incl. plug connector, parallel wiring to Speakon connector.
4. Fixing hole with removable stopper. It serves to secure the enclosure after it has been
hung onto the mounting points. During use, the fixing hole must either be closed by the
stopper or a fixing screw. Otherwise, strong interference may occur.
5. Speaker Enclosure
6. Speaker Chassis
7. Front grille, mountable and demountable without tools.
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 6 of 21
2.3 Required signal processor
The following information does not apply to the option "XO" :
When using the SONA SUB, a signal processor is required such as an electronic crossover or
the K&F Controller CD 44.
The signal processor must provide at least the following settings:
• 1 x high-pass 4th order Butterworth
• 1 x low-pass 3rd order Butterworth
• 1 x bell filter
• 1 x all-pass 1st order (Only if SONA 5 is filtered).
Further information in chapter Configuration and Connecting Diagram on page 13 ff.
2.4 Required mounting material
For wall and ceiling mounting:
• At least 3 screws (not countersunk) with
a thread diameter of 6 mm,
a head diameter of 10 mm minimum/ 13 mm maximum,
and a head height of 6 mm max.
• Rawlplugs or other suitable mounting aids with official technical approval
corresponding to the given requirements.
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 7 of 21
3. Safety Instructions
3.1 Mounting the Speakers / Wall and Ceiling Installation
Warning
Suspended loads are safety related.
The speakers may only be mounted by qualified event technicians or personnel which are
instructed by them, adequately. This also applies for wall and ceiling fixations.
The technicians responsible for assembling the speakers on site are responsible for the safe
setup and use of the speakers and guarantee the safe use of the mounting elements.
Never use signal cables or power cords for suspending, aligning or securing the systems.
Before carrying through ceiling and wall installations, it is essential to consider the load
capacity, the stability and type of the construction of walls, ceilings and panelling. If there is
wall panelling, for example, it is then necessary to examine the solidity of the wall and use
the appropriate wall plugs.
Note that the suspension points on the hall ceiling (i.e. shackles, suspension points, or chain
points) must comply with the accident prevention regulation BGV C1 (Event and Production
Sites for Stage Presentations) or comparable applicable national standards, and the total load
must be approved by an authorised expert.
Make sure to comply with the stipulated tightening torques.
If not otherwise stated in this manual, only original KLING & FREITAG parts may be used for
mounting the speakers. The use of other parts – in particular parts by other manufacturers –
is not permitted in this case.
Ensure that all installation connections comply with the applicable safety guidelines and that
the size and strength are sufficient.
Ensure that all connections are secured against coming loose and that only authorized,
statically tested and correctly sized supports, mounting equipment, wire ropes and chains are
used.
As a basic principle, you must visually inspect all safety-relevant components of the speaker
and the accessory before every use. If there are signs of wear, cracks, or deformation, then
you must replace the parts immediately. The visual inspection also includes checking the
screwed connections on supporting elements.
The information described here does not relieve the user of the duty to follow the given
safety requirements and legal regulations.
3.2 Notes for Mounting the Speakers
Warning
Mount the speakers securely. To avoid injury or damage, always be sure to mount the
speakers securely so that they do not fall.
Please note that speakers can move as a result of vibrations. To prevent them from falling
from their mounted position, they must be secured properly.
When laying out the connecting cables, make sure that nobody can trip.
3.3 Preventing hearing damage
Caution
Avoid beeing too close to operating speakers. This equipment is capable of delivering sound
pressure levels in excess of 90 dB SPL, which may cause permanent hearing damage.
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 8 of 21
3.4 Protecting the Speakers / Operating Safety
In general, audio signals must not be overdriven. This may be caused by mixing consoles,
equalizers, effect equipment, etc. and should be indicated on this equipment. When a power
amplifier is overloaded at the output (clipping), then the amplifier should activate a clipping
warning signal. Power amplifiers can also be overloaded at the input circuit without the
amplifier signalling the clipping, i.e. when there is not sufficient headroom in the input
circuit. We, therefore, recommend turning up the power amplifiers all the way and adjusting
the level before the power amplifier in order to avoid overloading the input circuit. In any
case, the signal must be reduced as soon as it sounds unnaturally distorted.
Operations without CD 44 Controller:
• To protect the speakers from being destroyed and to avoid fire hazard, they should
only be operated with professional power amplifiers with a maximum rated output
power of 150W@8Ohm.
• If power amplifiers have power ratings lower than 75W@8Ohm, then it is imperative
that the amplifiers have clipping limiters. Alternately, you can also insert a clipping
limiter before the amplifier.
• To achieve sensible acoustic results and to protect the speaker from mechanical
destruction during use, the speaker must be filtered according to this manual. See
chapter Configuration and Connecting Diagram from page 13.
Operations with CD 44 Controller:
• For optimal performance and operating safety of the SONA SUB speakers we
recommend using the system controller K&F CD 44.
• When operating the loudspeaker with amplifers without clipping limiter and nominal
amplifier power less than 75W@8Ohm requires to set a Limit Reduction of 3dB for the
K&F CD 44 controller.
• The destruction of speakers and the risk of fire as a result of a very rare power
amplifier or speaker defect may not be avoided by the controller in any case.
For damage caused by
• overloading the speakers
• using power amplifiers with other than the recommended maximum output power
we do not assume warranty and excludes liability for possible consequential damage.
The following signals may damage the speakers:
• clipping power amplifiers
• permanent high-level signals with high frequency and continuous noise from feedback.
• permanently distorted high-level signals.
• noises, which occur when the amplifier is on while equipment is being connected,
disconnected or switched on.
Do not install devices in any of the following places:
• where the devices are permanently exposed to direct sunlight.
• where the devices are exposed to high moisture or rain.
• where the devices are exposed to strong vibrations and dust.
Avoid damage caused by the speakers' magnetic fields
Speakers are permanently surrounded by a magnetic field, even when they are not
connected. Therefore, during transport and placement of the speakers, it is important to
ensure that there is a sufficient distance between the speakers and magnetic data media and
computer/video monitors (except flat panels).
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 9 of 21
4. Wall and Ceiling Installation
Using the provided drilling plan, mark the mounting points on the wall or ceiling.
Caution
When mounting, always choose at least two of the mounting points as well as the fixation
point. Choose fasteners that are suitable for the wall or ceiling material. Use suitable
rawlplugs if necessary.
Horizontal wall mounting
Vertical wall mounting
Ceiling mounting
User's manual K&F SONA SUB
KLING & FREITAG GMBH © 2014 Version 2.1 Page 10 of 21
Remove the grille:
Push one side of the grille towards the
middle of the speaker (1).
Keep pushing the side and, while doing
so, slide the side of the grille upwards out
of the fastening groove (2).
Now slide the other side of the grille
towards the middle of the speaker (1).
Remove the grille by pulling it upwards
out of the fastening groove. (2).
Turn the screws for the keyhole mounting
points into the wall.
~ 6 - 7 mm
Remove the stopper in the fixing hole (1).
Connect the speaker cables. Follow the
instructions in chapter Wiring beginning
on page 16.
At the keyhole mounting points, hang the
speaker onto the screws (2) .
Fixate the speaker with the fixing screw
(3).
During use, the fixing bore must be
closed by a fixing screw. If not, strong
interference may occur.
Otros manuales para SONA SUB
1
Tabla de contenidos
Otros manuales de Subwoofer de KLING & FREITAG
KLING & FREITAG
KLING & FREITAG SW Series Manual de usuario
KLING & FREITAG
KLING & FREITAG PASSIO SUB 15 Manual de usuario
KLING & FREITAG
KLING & FREITAG ,SP' Manual de usuario
KLING & FREITAG
KLING & FREITAG NOMOS LT Manual de usuario
KLING & FREITAG
KLING & FREITAG PASSIO SUB 12 Manual de usuario
KLING & FREITAG
KLING & FREITAG NOMOS XLS Manual de usuario
KLING & FREITAG
KLING & FREITAG NOMOS XLT Manual de usuario
KLING & FREITAG
KLING & FREITAG Self powered Manual de usuario
