KitchenAid 27" Manual de usuario

INSTALLATION INSTRUCTIONS

24" (61 CM), 27" (68.6 CM), AND 30" (76.2 CM)

INDOOR/OUTDOOR ELECTRIC WARMING DRAWER

INSTRUCTIONS D'INSTALLATION

TIROIR-RÉCHAUD ÉLECTRIQUE POUR USAGE

INTÉRIEUR/EXTÉRIEUR DE 24" (61 CM),

27" (68,6 CM), ET 30" (76,2 CM)

Table of Contents/Table des matières

WARMING DRAWER SAFETY ......................................................2

INSTALLATION REQUIREMENTS................................................3

Tools and Parts ............................................................................3

Location Requirements................................................................3

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS..................................................6

Install Warming Drawer................................................................6

Complete Installation ...................................................................7

CUSTOM DRAWER FRONT INSTALLATION

INSTRUCTIONS FOR WARMING DRAWERS..............................7

Tools and Parts ............................................................................7

Install Custom Drawer Front Panel ..............................................7

SÉCURITÉ DU TIROIR-RÉCHAUD ...............................................9

EXIGENCES D’INSTALLATION...................................................10

Outillage et pièces......................................................................10

Exigences d’emplacement.........................................................10

Spécifications électriques ..........................................................13

INSTRUCTIONS D'INSTALLATION.............................................13

Installation du tiroir-réchaud ......................................................13

Achever l'installation ..................................................................14

INSTRUCTIONS D'INSTALLATION DE LA FAÇADE

DU TIROIR PERSONNALISÉ POUR TIROIR-RÉCHAUD..........14

Outillage et pièces......................................................................14

Installation du panneau de la façade du tiroir personnalisé......14

IMPORTANT:

Save for local electrical inspector's use.

IMPORTANT :

À conserver pour consultation par l'inspecteur local des installations électriques.

W10713339A

www.goedekers.com

WARMING DRAWER SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

www.goedekers.com

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

■Phillips screwdriver

■Flat-blade screwdriver

■Measuring tape

■Level

■Drill

■1³⁄₈" (3.5 cm) hole saw

Parts Supplied

■Two #8–18 x ¹⁄₂" screws

■Lens (for panel ready models)

Check local codes. Check existing electrical supply. See

“Electrical Requirements.”

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■Cutout dimensions that are shown must be used. Given

dimensions provide minimum clearance with warming drawer.

■Recessed installation area must provide complete enclosure

around the recessed portion of the warming drawer.

■Grounded electrical supply is required. See “Electrical

Requirements” section.

■Electrical supply outlet should be located in the rear wall on

the upper right-hand side of the cutout or in an adjacent

cabinet. The outlet must be recessed. If the electrical outlet is

located in an adjacent cabinet, a 1³⁄₈" (3.5 cm) minimum

diameter hole should have been drilled in the back of the

cutout or support surface to pass the power supply cord

through to the outlet.

■Warming drawer support surface must be solid, level and flush

with bottom of cabinet cutout.

■Warming drawers with oiled bronze, black glass, and white

glass panels are approved for indoor use only.

■Support surface must be solid, level, and flush with the

bottom of the cabinet cutout.

■24" (61 cm) minimum cabinet depth.

For best performance results make sure the warming drawer is

leveled before completing installation. There is no way to level the

warming drawer after it has been installed. If the installation is not

level, the door may slide open or not seal tightly, allowing heat to

escape.

NOTE: If installing the warming drawer below another product,

refer to that product’s literature for any installation requirements.

Product Dimensions

WARMING

DRAWER

SIZE

OVEN

DEPTH(A) RECESSED

WIDTH (B) RECESSED

HEIGHT (C) OVERALL

WIDTH (D) DRAWER

FRONT

HEIGHT (E)

24"

(61 cm) 23¹⁄₈"

(58.7 cm) 22¹⁄₄"

(56.5 cm) 9"

(22.9 cm) 23³⁄₄"

(60.3 cm) 10¹⁄₄"

(26.1 cm)

27"

(68.6 cm) 23¹⁄₈"

(58.7 cm) 25¹⁄₄"

(64.1 cm) 9"

(22.9 cm) 26³⁄₄"

(67.9 cm) 10¹⁄₄"

(26.1 cm)

30"

(76.2 cm) 23¹⁄₈"

(58.7 cm) 28¹⁄₄"

(71.8 cm) 9"

(22.9 cm) 29³⁄₄"

(75.6 cm) 10¹⁄₄"

(26.1 cm)

www.goedekers.com

Clearance Dimensions

Warming drawer can be installed as an indoor single or double

installation or installed under a single oven. Two warming drawers

under a single oven are shown.

NOTE: The warming drawer cannot be leveled after being

installed.

For outdoor installation, follow the cutout dimensions above.

Install the outdoor warming drawer in a permanent fixture.

Custom Wood Drawer Front

If you plan to install a custom wood panel to match your

cabinets, we recommend consulting a qualified cabinetmaker or

carpenter. The back of the wood panel must be sealed to avoid

moisture damage.

Toe

kick

Warming

drawer

cutouts

120 volt

grounded

outlet

(or located

in adjacent

cabinet)

Front view

WARMING

DRAWER SIZE MINIMUM

BETWEEN

CUTOUTS (A)

CUTOUT

HEIGHT (B) MINIMUM/

RECOMMENDED (C) CUTOUT

WIDTH (D) MINIMUM

CABINET

WIDTH (E)

24" (61 cm) 2¹⁄₂" (6.4 cm) 9¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4¹⁄₄" (10.8 cm) 22¹⁄₂" (57.1 cm) 24" (61 cm)

27" (68.6 cm) 2¹⁄₂" (6.4 cm) 9¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4¹⁄₄" (10.8 cm) 25¹⁄₂" (64.8 cm) 27" (68.6 cm)

30" (76.2 cm) 2¹⁄₂" (6.4 cm) 9¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4¹⁄₄" (10.8 cm) 28¹⁄₂" (72.4 cm) 30" (76.2 cm)

www.goedekers.com

Clearance Dimensions - Flush Installation

Flush Installation Requirements

A 25³⁄₈" (64.5 cm) minimum cutout depth is required.

These dimensions will result in a ¹⁄₄" (6 mm) reveal on all sides of the warming drawer.

The front face of the cleats and platforms will be visible and should be treated as a finished surface.

27" Models 30" Models

AWidth of flush inset cutout (minimum) 27¹⁄₄" (69.2 cm) 30¹⁄₄" (76.8 cm)

BHeight between cutouts (minimum) 2¹⁄₂" (6.4 cm) 2¹⁄₂" (6.4 cm)

CHeight of flush inset cutout (minimum) 10³⁄₄" (27.3 cm) 10³⁄₄" (27.3 cm)

DBottom of cutout to floor (recommended) 8¹⁄₄" (21.0 cm) 8¹⁄₄" (21.0 cm)

Bottom of cutout to floor (minimum) 5" (12.7 cm) 5" (12.7 cm)

EWidth of opening (minimum) 25¹⁄₄" (64.1 cm) 28¹⁄₄" (71.8 cm)

FDepth of cutout (minimum) 25³⁄₈" (64.5 cm) 25³⁄₈" (64.5 cm)

eRecommended outlet location

1" (25 mm)

Side Cleats*

⁷⁄₈” (22 mm)

Platform*

Front View

Side Cleat*

1⁵⁄₈" (4.1 cm)

Top View

Cabinet

Back

Side View

www.goedekers.com

Electrical Requirements

IMPORTANT: The warming drawer must be electrically grounded

in accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70 or

Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this warming drawer be provided.

■The model/serial/rating plate is located above the left-hand

side receiving slide. The warming drawer must be removed to

view the model/serial/rating plate. See the illustration below.

INSTALLATION INSTRUCTIONS

Install Warming Drawer

1. Turn off power supply. Using 2 or more people, move

warming drawer close to its final location. Remove and

discard shipping materials, tape, and film from the warming

drawer. Remove and set aside racks and other parts from

inside warming drawer.

2. Check that the warming drawer Temperature control knob is

set to the OFF position.

3. Support the warming drawer on a sturdy surface level with

the cutout opening.

4. Plug the power supply cord into the grounded 3 prong outlet.

5. Slide the warming drawer over halfway into the cutout

opening.

6. Open warming drawer and slowly push against the front

panel to slide the drawer completely into the cabinet until the

flanges on the front panel meet the cabinet face.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A. Model/serial/rating plate

WARNING

Excessive Weight Hazard

Use two or more people to move and install

warming drawer.

Failure to do so can result in back or other injury.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

www.goedekers.com

7. Use the two #8-18 x ¹⁄₂" screws provided to secure the

warming drawer frame to the cabinet. Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For warming drawer use and cleaning, read the Use and Care

Guide.

5. Push in and turn the control knob to HI, and the light should

illuminate.

If warming drawer(s) does not operate, check the

following:

■Household fuse is intact and tight; or circuit breaker has not

tripped.

■Warming drawer is plugged in, and electrical supply is

connected.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use

and Care Guide or contact the dealer from whom you purchased

your warming drawer.

CUSTOM DRAWER FRONT INSTALLATION INSTRUCTIONS

FOR WARMING DRAWERS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

■Phillips screwdriver

■Drill and appropriate bits

Parts Supplied

■6 - #8-18 x ¹⁄₂" screws

■Indicator light lens

Parts Needed

■Custom drawer front

■Custom handle (optional)

■Adhesive recommended for plastic to wood

Install Custom Drawer Front Panel

The warming drawer has an interface that will allow a modest

range of panel sizes. The actual panel size should be selected by

the customer and the contractor to suit the desired effect. It is

recommended that a qualified carpenter make and install the

custom drawer front and handle(s) to match surrounding

cabinetry.

1. Install warming drawer unit as instructed by the installation

instructions provided with the warming drawer.

2. Create the custom drawer front. Below are the minimum and

maximum dimensions for the custom drawer front. The size

of the custom drawer front for the warming drawer will vary

according to the specific installation. The depth of the panel

will vary in order to have the custom warming drawer flush

with the surrounding cabinets.

A. Two #8–18 x

¹⁄₂

" screws

Model A - MAX B - MAX A - MIN B - MIN

24" (61 cm)

Warming Drawer 23³⁄₄"

(60.3 cm) 10⁵⁄₁₆"

(26.2 cm) 23"

(58.4 cm) 9¹⁄₁₆"

(23.0 cm)

27" (68.6 cm)

Warming Drawer 26³⁄₄"

(67.9 cm) 10⁵⁄₁₆"

(26.2 cm) 26"

(66.1 cm) 9¹⁄₁₆"

(23.0 cm)

30" (76.2 cm)

Warming Drawer 29³⁄₄"

(75.6 cm) 10⁵⁄₁₆"

(26.2 cm) 29"

(73.7 cm) 9¹⁄₁₆"

(23.0 cm)

⁵⁄₁₆" (7.9 mm) dia. hole for

indicator light lens (provided

in this kit). Locate lens directly

in front of indicator light.

www.goedekers.com

3. It is recommended that if a wood or porous custom drawer

front is installed, a high quality spar polyurethane finish be

applied to the inner wood surface.

4. For the lens, drill a ⁵⁄₁₆" (7.9 mm) diameter hole through the

appearance side of the custom drawer front. This hole will

allow the indicator “ON” light to be visible through the custom

drawer front. To secure the lens, use an adhesive specified for

plastic to wood application.

5. Install custom handle (not supplied) through custom drawer

front.

6. The custom drawer front is fastened to the stainless steel

drawer by driving 6 screws through clearance holes in the

drawer front into the wooden or other custom made panel.

A. Optional handle

B. Custom door panel

C. Warming drawer front

D. 6 - #8-18 x

¹⁄₂

" screws

E. Lens

www.goedekers.com

SÉCURITÉ DU TIROIR-RÉCHAUD

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

www.goedekers.com

EXIGENCES D’INSTALLATION

Outillage et pièces

Rassembler les outils et pièces nécessaires avant d’entreprendre

l’installation. Lire et observer les instructions fournies avec

chacun des outils de la liste ci-dessous.

Outils nécessaires

■Tournevis Phillips

■Tournevis à lame plate

■Mètre ruban

■Niveau

■Perceuse

■Scie-cloche de 1³⁄₈" (3,5 cm)

Pièces fournies

■Deux vis n° 8 de 18 x ¹⁄₂"

■Cabochon (pour les modèles avec panneaux prêts-à-installer)

Consulter les codes locaux. Vérifier l’alimentation électrique

existante. Voir “Spécifications électriques”.

Il est recommandé de faire réaliser tous les raccordements

électriques par un électricien qualifié agréé.

Exigences d’emplacement

IMPORTANT : Observer les dispositions de tous les codes et

règlements en vigueur.

■Il est nécessaire d'utiliser les dimensions de l’ouverture à

découper indiquées. Ces dimensions prennent en compte les

dégagements de séparation minimums à respecter pour le

tiroir-réchaud.

■L’espace d’installation dans un encastrement doit permettre la

formation d’une enceinte complète autour de la partie

encastrée du tiroir-réchaud.

■Une source d’électricité avec liaison à la terre est nécessaire.

Voir “Spécifications électriques”.

■La prise électrique doit être située dans le mur arrière du côté

supérieur droit de l’ouverture ou dans un placard adjacent. La

prise doit être encastrée. Si la prise électrique est située dans

un placard adjacent, un trou de 1³⁄₈" (3,5 cm) de diamètre

minimum doit avoir été percé à l’arrière de l’ouverture ou de

la surface de support pour faire passer le cordon

d’alimentation.

■La surface de support du tiroir-réchaud doit être robuste,

d’aplomb et en affleurement avec le bas de l’ouverture

découpée dans le placard.

■Les tiroirs-réchaud avec panneaux en bronze huilé, en verre

noir ou verre blanc sont approuvés pour une utilisation en

intérieur uniquement.

■La surface de support doit être robuste, d’aplomb et en

affleurement avec le bas de l’ouverture découpée dans le

placard.

■Profondeur de placard minimale : 24" (61 cm)

Pour le meilleur rendement, vérifier que le tiroir-réchaud est

d’aplomb avant d’achever l’installation. Il est impossible de régler

l’aplomb du tiroir-réchaud après son installation. Si l’installation

n’est pas d’aplomb, la porte risque de s’ouvrir ou de ne pas

fermer hermétiquement, ce qui laissera la chaleur s’échapper.

REMARQUE : Si le tiroir-réchaud est installé en-dessous d'un

autre produit, consulter la documentation de ce produit pour

connaître les exigences d'installation.

Dimensions du produit

TAILLEDU

TIROIR-

RÉCHAUD

PROFON

DEUR DU

FOUR (A)

LARGEUR DE

L’ENCASTREMENT (B) HAUTEUR DE

L’ENCASTREMENT (C) LARGEUR

TOTALE (D) HAUTEUR DE

L'AVANT DU

TIROIR (E)

24"

(61 cm) 23¹⁄₈"

(58,7 cm) 22¹⁄₄"

(56,5 cm) 9"

(22,9 cm) 23³⁄₄"

(60,3 cm) 10¹⁄₄"

(26,1 cm)

27"

(68,6 cm) 23¹⁄₈"

(58,7 cm) 25¹⁄₄"

(64,1 cm) 9"

(22,9 cm) 26³⁄₄"

(67,9 cm) 10¹⁄₄"

(26,1 cm)

30"

(76,2 cm) 23¹⁄₈"

(58,7 cm) 28¹⁄₄"

(71,8 cm) 9"

(22,9 cm) 29³⁄₄"

(75,6 cm) 10¹⁄₄"

(26,1 cm)

www.goedekers.com

Otros manuales para 27"

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cajón calentador de KitchenAid

KitchenAid

KitchenAid KEWD105 Manual de usuario

KitchenAid

KitchenAid 27" (68.6 cm) Warming Drawer Manual de usuario

KitchenAid

KitchenAid KEWS175SPA03 Manual de usuario

KitchenAid

KitchenAid KEWS175SPA00 Manual de usuario

KitchenAid

KitchenAid KEWS105SPA00 Manual de usuario

KitchenAid

KitchenAid KEWD105 Manual de usuario

KitchenAid

KitchenAid KEWS145SPA00 Manual de usuario

KitchenAid

KitchenAid KEWS145SPA03 Manual de usuario

KitchenAid

KitchenAid KBUU142T Manual de usuario

KitchenAid

KitchenAid 4452827 Manual de usuario

KitchenAid

KitchenAid KEWS145SPA02 Manual de usuario

KitchenAid

KitchenAid W10133235 Manual de usuario

KitchenAid

KitchenAid KEWS175 Manual de usuario

KitchenAid

KitchenAid KEWS105BSS00 Manual de usuario

KitchenAid

KitchenAid KEWS105SPA03 Manual de usuario

KitchenAid

KitchenAid KSDX 1440 Manual de usuario

KitchenAid

KitchenAid KEWS105SPA Manual de usuario

KitchenAid

KitchenAid KEWS105B Manual de lista de piezas

KitchenAid

KitchenAid KEWD175HBL0 Manual de usuario

KitchenAid

KitchenAid KEWS105B Instrucciones de uso

KitchenAid

KitchenAid 24" (61 cm) Warming Drawer Manual de usuario

KitchenAid

KitchenAid KEWS105S Manual de lista de piezas

KitchenAid

KitchenAid KEWS145SPA01 Manual de usuario

KitchenAid

KitchenAid KOWT107ESS Manual de usuario

Manuales populares de Cajón calentador de otras marcas

Siemens

Siemens HW 290 Series Manual de usuario

Hatco

Hatco HDW-1 Instrucciones de instalación

APW Wyott

APW Wyott WD-2CMF Manual de usuario

Viking

Viking DEWD102SS Manual de usuario

Miele

Miele ESW 6229 Manual de usuario

Brandt

Brandt WD1014X Manual de usuario

Gaggenau

Gaggenau WSP 222 Manual de usuario

DCS

DCS WDI Manual de usuario

Fisher & Paykel

Fisher & Paykel OR90SCG6R1 Manual de usuario

Electrolux

Electrolux EED21600X Manual de usuario

Fisher

Fisher PROFESSIONAL WB76SPEX1 Manual de usuario

Electrolux

Electrolux EW30WD55GS Manual de usuario

Hanseatic

Hanseatic TCN14J6D-S Manual de usuario

Jenn-Air

Jenn-Air JWD6030CDX Manual de usuario

Gaggenau

Gaggenau WS482710 Manual de usuario

Bosch

Bosch HWD2720UC Manual de usuario

NEFF

NEFF N29HA11Y2 Instrucciones de funcionamiento y mantenimiento

Fisher & Paykel

Fisher & Paykel WB60SMTB1-SET Manual de usuario