KitchenAid 5KSM45 Series Manual de usuario

Stand Mixer

5KSM45-5KSM180

W11389352A.indb 1 11/22/2019 11:52:24 AM

2 |

PARTS AND FEATURES

*Included with select models only. Also available as optional accessory.

**The bowl design and material depend on the Stand Mixer model.

611

1Speed control lever

2Motor head

3Attachment hub

4Attachment knob

5Motor head locking lever (not shown)

6Beater shaft

7Beater height adjustment screw

(not shown)

8Bowl clamping plate

9Bowl**

10 Pouring shield*

11 3 L stainless steel bowl*

12 Dough hook

13 Wire whip

14 Flex Edge beater*

15 Flat beater

W11389352A.indb 2 11/22/2019 11:52:25 AM

ENGLISH

| 3

STAND MIXER SAFETY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be

followed, including the following:

1. Read all instructions. Misuse of appliance may result in personal injury.

2. To protect against risk of electrical shock, do not put Stand Mixer in water or

other liquid.

3. This appliance is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

4. Turn the appliance OFF, then unplug from the outlet when not in use, before

assembling or disassembling parts and before cleaning. To unplug, grasp

the plug and pull from the outlet. Never pull from the power cord.

5. Avoid contacting moving parts. Keep hands, hair, clothing, as well as

spatulas and other utensils away from beater during operation to reduce the

risk of injury to persons and/or damage to the Stand Mixer.

6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions or is dropped or damaged in any manner. Return

appliance to the nearest Authorised Service Centre for examination, repair or

adjustment.

7. The use of attachments not recommended or sold by KitchenAid may cause

fire, electrical shock or injury.

8. Do not use the Stand Mixer outdoors.

9. Do not let the cord hang over edge of table or counter.

10. Remove flat beater, wire whip, or dough hook from Stand Mixer before

washing.

W11389352A.indb 3 11/22/2019 11:52:25 AM

4 |

11. Children should be supervised to ensure that they do not play with the

appliance.

12. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent, or similarly qualified persons in order to avoid a hazard.

13. Never leave the appliance unattended while it is in operation.

14. To avoid product damage, do not use the Stand Mixer bowls in areas of high

heat such as an oven, microwave, or on a stovetop.

15. Refer to the “Care and Cleaning” section for instructions on cleaning the

surfaces in contact with food.

16. This appliance is intended to be used in household and similar applications

such as:

- staff kitchen areas in shops, offices, or other working environments;

- farmhouses;

- by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments.

SAVE THESE INSTRUCTIONS

STAND MIXER SAFETY

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these

instructions can result in

death, fire, or electrical shock.

Wattage:

300 Watts MAX

for 5KSM125 - 5KSM180 Series

275 Watts MAX

for 5KSM45, 5KSM95 Series

Voltage: 220-240 V

Hertz: 50-60 Hz

NOTE: If the plug does not fit in the

outlet, contact a qualified electrician.

Do not modify the plug in any way.

Do not use an adapter.

Do not use an extension cord. If the power

supply cord is too short, have a qualified

electrician or service technician install an

outlet near the appliance.

W11389352A.indb 4 11/22/2019 11:52:25 AM

ENGLISH

| 5

NOTE: The speed control lever can be set between the speeds listed in the above chart to

obtain speeds 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when

preparing yeast doughs as this may cause damage to the Stand Mixer.

SPEED CONTROL GUIDE

Speed Action Attachment Description

1Stir

For slow stirring, combining, mashing,

starting all mixing procedures. Use to add

ﬂour and dry ingredients to batter and to

add liquids to dry ingredients. Do not use

Speed 1 to mix or knead yeast doughs.

2Slow

Mixing

For slow mixing, mashing, faster stirring.

Use to mix and knead yeast doughs,

heavy batters and candies, start mashing

potatoes or other vegetables, cut

shortening into ﬂour, mix thin or splashy

batters.

4Mixing,

Beating

For mixing semi-heavy batters, such

as cookies. Use to combine sugar and

shortening and to add sugar to egg

whites for meringues. Medium speed for

cake mixes.

6Beating,

Creaming

For medium fast beating (creaming) or

whipping. Use to ﬁnish mixing cake,

doughnut, and other batters. High speed

for cake mixes.

8Fast

Beating,

Whipping

For whipping cream, egg whites, and

boiled frostings.

10 Fast

Whipping

For whipping small amounts of cream,

egg whites, or for ﬁnal whipping of

mashed potatoes.

USING THE STAND MIXER

ACCESSORY GUIDE

Accessory Uses

Flat beater and

Flex Edge beater*

for normal to heavy mixtures:

Cakes, creamed frostings, candies,

cookies, pie pastry, biscuits, meat

loaf, mashed potatoes

Wire whip for mixtures that

need air incorporated:

Eggs, egg whites, heavy cream,

boiled frostings, sponge cakes,

mayonnaise, some candies

Dough hook for mixing and

kneading yeast doughs:

Breads, rolls, pizza dough, buns

*Included with select models only. Also available as optional accessory.

W11389352A.indb 5 11/22/2019 11:52:26 AM

6 |

ATTACHING/REMOVING THE BOWL

USING THE STAND MIXER

LIFTING/LOWERING THE MOTOR HEAD

NOTE: Motor head should always be in LOCK position when using the Stand Mixer.

To attach bowl: Turn speed control to

“0.” Unplug Stand Mixer.

To lift motor head: Push the locking lever

to the UNLOCK position and lift the head.

Once lifted, the lever will automatically go

back in LOCK position to keep the head

lifted.

Place bowl on bowl clamping plate. Turn

bowl gently in clockwise direction.

Hold the locking lever in the UNLOCK

position and tilt motor head back.

To put down motor head: Push the

locking lever to UNLOCK and gently

bring the head down. The locking lever

will automatically go back in LOCK

position when the head is down. Before

mixing, test lock by attempting to raise

motor head.

To remove bowl: Repeat steps 1 and 2.

Turn bowl gently counterclockwise.

W11389352A.indb 6 11/22/2019 11:52:26 AM

ENGLISH

| 7

USING THE STAND MIXER

*Included with select models only. Also available as optional accessory.

ATTACHING/REMOVING THE FLAT BEATER, FLEX EDGE BEATER*,

WIRE WHIP, OR DOUGH HOOK

To attach accessory: Turn speed control

to “0”. Unplug Stand Mixer.

To remove accessory: Repeat steps 1

and 2. Press accessory upward as far as

possible and turn to the left. Then pull

accessory from the beater shaft.

Hold the locking lever in the UNLOCK

position and tilt motor head back.

Slip accessory onto beater shaft and press

upward as far as possible. Then, turn

accessory to the right, hooking accessory

over the pin on the shaft.

W11389352A.indb 7 11/22/2019 11:52:26 AM

8 |

USING THE STAND MIXER

PLACING/REMOVING THE POURING SHIELD*

*Included with select models only. Also available as an optional accessory.

BEATER TO BOWL CLEARANCE

Your Stand Mixer is adjusted at the factory so the ﬂat beater just clears the bottom of the

bowl. If, for any reason, the ﬂat beater hits the bottom of the bowl or is too far away from

the bowl, you can correct clearance easily.

NOTE: When properly adjusted, the flat beater will not strike on the bottom or side of

the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the

bowl, coating may wear off the beater or wires on whip may wear.

Turn speed control to “0”. Unplug Stand

Mixer.

To place pouring shield: Turn speed

control to “0”. Unplug Stand Mixer.

Attach your chosen accessory. See the

“Attaching/removing the flat beater, wire

whip, or dough hook” section.

Lift motor head. Turn screw slightly

counterclockwise (left) to raise flat beater

or clockwise (right) to lower flat beater.

Make adjustment with flat beater, so

it just clears surface of bowl. If you

overadjust the screw, the bowl lock lever

may not lock into place.

From the front of the Stand Mixer, slide

the pouring shield over the bowl until the

shield is centred. The bottom rim of the

shield should fit within the bowl.

W11389352A.indb 8 11/22/2019 11:52:27 AM

ENGLISH

| 9

USING THE STAND MIXER

USING THE POURING SHIELD*

Use the pouring shield to avoid having ingredients splashing out of the bowl when

mixing, as well as to easily pour ingredients in the bowl while mixing.

*Included with select models only. Also available as an optional accessory.

To remove pouring shield: Turn speed

control to “0”. Unplug Stand Mixer.

Lift the front of the pouring shield clear

of the bowl rim and pull forward. Remove

attachment and bowl.

For best results, rotate the shield so the

motor head covers the U-shaped gap in

the shield. The pouring chute will be just

to the right of the attachment hub asyou

face the Stand Mixer.

Pour the ingredients into the bowl

through the pouring chute.

W11389352A.indb 9 11/22/2019 11:52:27 AM

10 |

USING THE STAND MIXER

OPTIONAL ATTACHMENTS

KitchenAid offers a wide range of optional attachments such as food grinders or

pasta makers. They may be attached to the Stand Mixer attachment power shaft,

as shown here.

OPERATING THE SPEED CONTROL

NOTE: The Stand Mixer may warm up during use. Under heavy loads with extended

mixing time, the top of the unit may become hot. This is normal.

Plug Stand Mixer into proper electrical

outlet. Always set speed control lever

on lowest speed to start, then gradually

increase speed to avoid splashing

ingredients. See “Speed control guide”

chart.

To attach: Turn speed control to “0”.

Unplug Stand Mixer.

Do not scrape bowl while Stand Mixer

is operating. The bowl and beater are

designed to provide thorough mixing

without frequent scraping. Scraping

the bowl once or twice during mixing is

usually sufficient.

Loosen attachment knob by turning it

counterclockwise. Remove attachment

hub cover.

W11389352A.indb 10 11/22/2019 11:52:27 AM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mezclador de KitchenAid

KitchenAid

KitchenAid 5KPM50 Manual de usuario

KitchenAid

KitchenAid KPM50 WH Manual de usuario

KitchenAid

KitchenAid 5KSM1JA Manual de usuario

KitchenAid

KitchenAid 9KSM95 Series Manual de usuario

KitchenAid

KitchenAid KJG01A Series Manual de usuario

KitchenAid

KitchenAid KP2671X Series Guía rápida

KitchenAid

KitchenAid 4KG25H3XWH5 Guía rápida

KitchenAid

KitchenAid KSM158GBCA - 90th Anniversary Limited-Edition Stand... Manual de usuario

KitchenAid

KitchenAid KV25G0XER Manual de usuario

KitchenAid

KitchenAid KP26M8XMC5 Manual de usuario

KitchenAid

KitchenAid 5KSM7990XBSM Manual de usuario

KitchenAid

KitchenAid 5KSM150PS Manual de usuario

KitchenAid

KitchenAid 5KSM7586P Manual de usuario

KitchenAid

KitchenAid KSM2CB5PCS Manual de usuario

KitchenAid

KitchenAid 5K45SS Manual de usuario

KitchenAid

KitchenAid KSM3316XWH0 Manual de usuario

KitchenAid

KitchenAid KV25G0XAQ Manual de usuario

KitchenAid

KitchenAid 5KSM7580XEOB Manual de usuario

KitchenAid

KitchenAid 5KSM180LE Manual de usuario

KitchenAid

KitchenAid K45SSWH Guía rápida

KitchenAid

KitchenAid 5KSM7990 Manual de usuario

KitchenAid

KitchenAid KSM175 Manual de usuario

KitchenAid

KitchenAid Pro Line Series Manual de usuario

KitchenAid

KitchenAid KV25G0XER - Professional 5 Plus 450 Watt Stand... Manual de usuario

Manuales populares de Mezclador de otras marcas

Bosch

Bosch GRW 9 Manual de usuario

MULTIQUIP

MULTIQUIP Whiteman WM45E Guía

Jay-Lor

Jay-Lor 5050 Manual de usuario

Sunbeam

Sunbeam FPSBSM210X Manual de usuario

MULTIQUIP

MULTIQUIP Whiteman MC94S Guía

Thinky

Thinky ARE-250 Manual de usuario

Midas

Midas XL4 Manual de usuario

bianco

bianco PURO 4 Manual de usuario

Paso

Paso DAG9200 Manual de usuario

Sima

Sima SFX-9A Manual de usuario

better chef

better chef IM-815WC Instrucciones de instalación

ALLEN & HEATH

ALLEN & HEATH GR1 Manual de usuario

Lacor

Lacor 69083 Hoja de especificaciones

M-Audio

M-Audio Midiman SAM Manual de usuario

Buffalo

Buffalo CP921 Manual de usuario

Pentair

Pentair HYPRO Cleanload 3376-0870 Instrucciones de operación

Cuisinart

Cuisinart SM50WHE Manual de usuario

Hobart

Hobart HCM-300 Manual de usuario