KING Jack OA8300 Manual de usuario
STEP 1: Verify all components and parts are included.
STEP 2: Install the KING Jack Antenna in one of two ways (page 2):
• RV Mounting: Mount to a bat wing style retractable arm using the supplied RV Antenna Bracket.
• Pole Mounting: Mount to a stationary pole (on a house for example) using the supplied Pole Mount
Bracket. DO NOT MOUNT TO A POLE ON A VEHICLE.
STEP 3: READ THE FOLLOWING INFORMATION CAREFULLY, THEN CHOOSE A CONNECTION OPTION
ON PAGE 3 AND MAKE CONNECTIONS.
STEP 4: Read the OPERATING INSTRUCTIONS on page 4 for antenna pointing instructions.
When using an existing power injector already in the RV
WARNING: DO NOT USE BOTH POWER INJECTORS!
existing RV antenna will be a wall
plate or an A/V distribution box with
an ON/OFF type switch.
When using the KING Jack antenna with the supplied power injector
STEP 1
STEP 2
STEP 3
STEP 4
Model OA8300
Power SupplyReception Frequencies
Page 2
POLE MUST BE STATIONARY:
NOT ON A VEHICLE.
This is a directional antenna
and should be rotated on the
maximum signal reception.
Option 1: BAT WING STYLE REPLACEMENT
2. Attach the RV antenna bracket to the KING Jack antenna with the 4 supplied screws.
clips (use new supplied retaining clips if necessary). You must mount antenna in relation to poles as shown below.
4. Fill end of existing coax cable with supplied dielectric grease and screw to antenna (DO NOT OVERTIGHTEN).
Note: If existing coax connector is corroded or damaged, replace with supplied new connector.
Option 2: POLE MOUNT BRACKET
same screws and washers.
3. Place the clamp around an appropriate pole and tighten wing nuts.
4. Fill end of coax cable (sold separately) with supplied dielectric grease and screw to antenna (DO NOT OVERTIGHTEN).
connector. Route coax cable and make appropriate connections.
IMPORTANT! Make sure to
mount head in relation to pole
heights as shown.
This will allow poles to fully
retract to stowed position.
Page 3
NOTE:
IMPORTANT!
Your RV may have more than one wall
plate. Do not use the power injector
supplied with the KING Jack antenna if
an existing power injector is present.
2. Turn on power to KING Jack antenna.
3. Perform a channel scan per the digital TV or digital TV
Choose one of those channels on your TV. Now monitor the signal strength
Page 4
www.kingconnect.com for additional information.
IMPORTANT! Do not power wash any part of the KING Jack antenna.
OPERATING INSTRUCTIONS: Scanning for Channels
LIMITED WARRANTY
of replacement parts after one year.
• Circumstances beyond the control of KING cause the product to no longer operate correctly.
• Customer is not the original owner.
In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of the warranty.
TROUBLESHOOTING
COURSE OF ACTION
No TV reception. No power to antenna.
is not lit.)
Antenna pointed in wrong
direction.
(sold separately)
11200 Hampshire Avenue South, Bloomington, MN 55438
PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com
NOTE:
channels each time you change locations.
NOTE:
Winegard is a registered trademark of Winegard Company.
KING Jack are products of KING®
® Company.
Tabla de contenidos
Otros manuales de Antena de KING Jack
KING Jack
KING Jack OA8501 Manual de usuario
KING Jack
KING Jack Classic OA8120/21 Series Manual de usuario
KING Jack
KING Jack OA8001 Manual de usuario
KING Jack
KING Jack OA8400 Manual de usuario
KING Jack
KING Jack OA8300 Manual de usuario
KING Jack
KING Jack OA8000 Manual de usuario
KING Jack
KING Jack AU8300 Manual de usuario
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
