Kinematica POLYTRON PT 1200 E Manual de usuario

LABORATORY LINE

POLYTRON® PT 1200 E

Hand Disperser (Ecoline), dispersing devices for budget-conscious labs

THE EXPERT FOR YOUR LABORATORY

Since more than 60 years we are perfecting the rotor/

stator technology, working in close cooperation with

users and universities. When using our technology,

yourtest samples will be dispersed into homogeneous

systems. Depending on the type of samples

you will get homogeneous emulsions, dispersions or

suspensions. This is the best foundation for all subsequent

analyses or formulations.

ERGONOMICS

– Easy operation with an on-off switch and speed control

– Lightweight

– Intelligent variable speed control for long equipment life

– Low noise

– Height adjust stand (available as an option)

– Switch aggregate quickly with Click & Go coupling

– Easy aggregate clean-up with EasyClean Design

RESULTS ARE CONVINCING

– Smallest sizes of particles / droplets: because precise

analysis require homogeneous samples

– Efﬁcient sample preparation: because fast dispersion

saves time

– Standard or custom-made aggregates: perfected for

and in cooperation with the users

– Cleaning and disassembly: EasyClean design makes

it very simple

– Quick coupling of the aggregates: by using Click & Go

– Best materials available: because without them,

we could not call it Swiss Made

– Durability is a Swiss virtue

This ergonomic hand disperser is lightweight and therefore ideal for rapid turnaround of smaller

sample volumes. The extensive range of dispersing aggregates covers a wide range of sample prepa-

ration applications.

PT 1200 E

Efﬁcient and Economical.

–

44mm

55 mm

220 mm

TECHNICAL INFORMATION

Processing volume

(water)

0.05 up to 250 ml

Tip speed Up to max. 14m/s

Up to max. 21m/s (X-Aggregate)

Applicable aggregates ø 3, 5, 7, 12 mm

ø 20mm X-Design

Speed range 0 to 25 000 rpm

Drive coupling Aggregates with E coupling

Noise level (drive without

aggregate)

≤ 65 dB(A) at 20 000 rpm

≤ 76 dB(A) at 25 000 rpm

Motor Universal with carbon brushes

Drive power 100W

Connection voltage 90 – 230 V ± 10%, 50Hz/60Hz

Relative humidity (max.) 80 % during storage

80 % during operation

Operating temperature 0 – 40 °C

Protection class acc. to

DIN

IP 20

Dimensions (LxW xH) Drive: 220 x 44 x 55mm

Power supply: 132 x58x 30mm

Weight Drive: 440g

Power supply: 310g

EMC standards IEC / EN 61000-6-2/ EN 61000-6-3

Safety standard IEC / EN 61010-2-51

USERS / APPLICATION RANGES

– General homogenizing applications

– Dispersions, suspensions, and emulsions

– Dispersion of plant, animal and human tissue samples

in various liquids and volumes

– Extraction of active pharmaceutical ingredients (API)

in pills and tablets

– Sample preparation for medical diagnostics and

RNA / DNA analysis

– Breakdown of animal and plant cells

– Emulsions and suspensions in tiny volumes

– Cell breakdowns for enzyme studies

– Preparation of samples for genetic studies

– Deagglomeration of cell complexes

This list provides a small selection of possible applications.

THE PRINCIPLE

The spinning rotor generates a vacuum. The sample is drawn

in and discharged to the outside through the stator’s slots.

Between the rotor / stator (shear gap), the product is subject

to high deceleration-tangential and radial acceleration forces.

The individual particles /droplets are torn apart and thus

reduced in size; they are reducedto several micrometers in

size through additional cutting and crashing effects.

THE RESULT

Microscopic dispersions, emulsions, suspensions, and

foams are generated. Droplets, particles, and gas bubbles

are reduced to several micrometers or smaller. Small and

large substances are dispersed more economically, faster,

and better than with any other system.

Your samples are efﬁciently «POLYTRONIZED».

Who is the inventor of it?

The roots of today’s Kinematica began in the former chemical/physical research institute of Prof. P.

Willems in Lucerne, Switzerland, the inventor of the modern rotor/ stator dispersion technology.

Kinematic dispersion.

Using the rotor / stator system.

–

STANDARD AGGREGATES (EC

DESIGN WITH TWO GEAR RINGS)

This is all you need for popular appli-

cations in the preparation of samples

and formulation development. The

cutting teeth embedded in the head of

the tool optimize the pre-crushing of

the sample. An enclosed ring design

provides optimum protection for those

teeth and prevents them from bending.

SPECIAL AGGREGATES (W, M, B,

SYN, Z & X DESIGN)

Specializations in the chemical,

pharmaceutical, cosmetic, and food

industry, as well as the life sciences,

makes new designs inevitable. These

aggregates are based on state-of-the-

art technology and only available from

Kinematica.

The highly specialized tool is subject

to further development that involves

close cooperation with our customers

and universities. Thus, it is continu-

ously perfected for speciﬁc applica-

tions.

MATERIALS

Whether you need a tool with

standard or special geometry, all

aggregates are manufactured from

high-alloy stainless steel 316L,

electrolytically polished and made in

Switzerland. Our synthetic aggregates

(SYN) are manufactured from the

highest quality materials available.

This guarantees their application at a

motor speed up to 30 000 rpm.

BEARINGS

All dispersing aggregates for the PT

1200 E are equipped with high-qual-

ity synthetic bearings. They exhibit

excellent mechanical properties and

chemical resistance. They are all FDA

approved.

CLEANING AND DISASSEMBLY

EasyClean: Our technology ensures

the simplest removal and fast clean-

ing, either by hand, dishwasher, or au-

toclave. Disassembling the precisely

ﬁtting components is simple and fast.

LOCKING SYSTEM

All our POLYTRON® aggregates

are ﬁtted with a high-precision quick-

release system: The Click & Go.

The high efﬁciency and the uniqueness of our POLYTRON® dispersing aggregate can only be

achieved through superior manufacturing precision and the sophisticated Kinematica design

method. This is 100 % Swiss Made.

Aggregate Technology.

Unrivaled.

–

EC STANDARD DISPERSING AGGREGATE

Design

The universal geometry uses two rows of teeth, is suitable

for a large spectrum of laboratory applications, and it is

reliable and efﬁcient.

Selection and applications

– All standard dispersing tasks

– Grinding of animal and human tissue samples in a variety

of ﬂuids and volumes

– Sample preparation for the extraction and dissolution of

organic materials

– Sample preparation for medical diagnostic procedures as

well as DNA analysis

– Extractions of systems / substances from vegetable-

derived samples

– Disruption of animal and human cells

– Deagglomeration of united cell structures

– Intensive mixing

SYN SYNTHETICS

Design

Disposable aggregates for the processing of multiple

samples per day, where the required sterilization of stainless

steel aggregates represents a signiﬁcant time limitation.

Available in PES / Special POM. Sterilepackaging in packet

sizes of 25 units each (ø 7 mm) and 10 units per packet

(ø 12 mm) each.

Selection and applications

– Prevention of X contamination

– All standard dispersing applications similar to EC aggregate

B BIOTRONA® HIGHTURBULENCE MIXER

Design

High-turbulence mixing head with the least possible shear

forces and energy inputs.

Selection and applications

– Quick removal and suspension of solid particles; also

suitable for high viscosity applications

Sales No. Product ø/ length

Volume ml

max. Tip

speed m/s

EC «STANDARD DISPERSING AGGREGATE»

11030004 PT-DA 03/ 2EC-E050 3/50 0.05 – 2 3

11030012 PT-DA 05/ 2EC-E085 5 /85 0.1 – 5 5

11030031 PT-DA 07/ 2EC-E107 7 / 107 0.3 – 10 7

11030062 PT-DA 12 /2EC-E123 12 / 123 2 – 250 12

11030042 PT-DA 12/ 2EC-E157 12 /157 2 – 250 12

SYN «SYNTHETICS»

11030030

25 x PT-DA 07/ 2SYN-E082*

7/82 0.3 – 10 7

11030037

25 x PT-DA 07/ 2SYN-E082**

7/82 0.3 – 10 7

11030038

12 x PT-DA 07/2SYN-E082**

7/82 0.3 – 10 7

11030035 10 x PT-DA 12/ 2SYN-E126* 12 / 126 2 – 250 12

11030036

10 x PT-DA 12/2SYN-E126**

12 / 126 2 – 250 12

*Sterile pack / **Non-sterile pack

B «BIOTRONA® HIGH-TURBULENCE MIXER»

11030034 PT-DA 07 /BEC-E107 7/107 10 – 100 7

11030286 PT-DA 12 /BEC-E157 12/ 157 50 – 500 12

Kinematica aggregates solve all problems you are faced with every day in the laboratory. Using our

Click & Go quick release makes the changing of aggregates very easy.

Dispersing aggregates for PT 1200 E.

Your applications, our solution.

–

M OUTSIDE CUTTING BLADES

Design

Outside blades pre-cut samples that are larger than

the rotors diameter. Subsequently, they can be dispersed

inside the generator.

Selection and applications

– Dispersing of large samples made simple

– All standard dispersing applications similar to EC aggregate

Z ZDESIGN

Design

Breaking up of hard probes, with integrated V-notch

technology. Additional, integrated holes for cleaning.

Selection and applications

– Hard and brittle material

– Sweet corn and grain

– Breaking, opening and dispersing of pills

– Breaking, hard grains

W WDESIGN

Design

The W-design prevents ﬁbrous, stringy or solid samples

from clogging the rotor/stator.

Selection and applications

– Dispersing ﬁbrous, stringy or solid samples

(e.g., pieces of meat)

– All standard dispersing applications similar to EC aggregate

X XDESIGN

Design

A special geometry designed for dispersing tablets

and pills or for preventing suppositories from clogging

or agglutinating.

Selection and applications

– Ultrafast crushing of tablets, coated pills, and

suppositories

– Basis for the analysis of active pharmaceutical

ingredients (APIs)

– Used in the substance analysis or for the quality control

during the production of tablets

Sales No. Product ø / length

Volume ml max. Tip

speed m/s

M «OUTSIDE CUTTING BLADES»

11030266 PT-DA 12 /2MEC-E157 12 /157 2 – 250 14

Z ZDESIGN

11030067 PT-DA 12/ 2ZMEC-E157* 12/ 157 2 – 250 12

* Z-Design aggregate with knives

W WDESIGN

11030060 PT-DA 12 / 2WEC-E157 12 / 157 2 – 250 14

X «X-DESIGN»

11030255 PT-DA 20/ 2XEC-E116 20/ 116 min. 10* 21

*When using a vessel ø 22mm / volume is always dependent

on the diameter of the vessel

Step 1 Step 2 Step 3

THE PROBLEM

For normal cylindrical beakers, the ﬂow creates a vortex.

The mixing and dispersing efﬁciency decreases considerably

since the product is no longer being optimally processed

through the dispersing generator head. This lengthens

processing times, requiring more energy input. Depending

on the shape of the vortex, this may also lead to additional

air being introduced.

THE SOLUTION

Our specially designed GS jars have a cloverleaf-like shape.

This effectively interrupts the ﬂow in the radial direction and

generates additional counteracting forces. These high turbu-

lences maximize the mixing and dispersion efﬁciency, thus

minimizing processing time and requiring less energy.

THE SELECTION

Our GS-glasses are available in chemical- and tempera-

ture-resistant borosilicate glass or in stainless steel, with

working volumes from a few milliliters to several liters,

with or without lid and with or without sealed feedthrough.

Choosing the right dispersing aggregate is crucial for good results. The right vessel

also contibutes to achive the desired result.

Dispersing vessels.

For best results.

–

GS vessel principle (viewed from top)

Sales No. Product

Ø/H

(mm)

Process

volume

Thickness Thread Description

Open on top

11051010 GS 15 30 / 100 35ml 2.8 mm – –

11051011 GS 25 54 / 150 150 ml 3.5 mm – –

With screw cap and sealing

11051020 GS 15K 30 / 100 35ml 2.8 mm GL25 –

11051021 GS 25K 54 / 150 150 ml 3.5 mm GL45 –

Incl. cover with sealing and hole

11051030 GS 15KL08 30/ 100 35 ml 2.8 mm GL25 8 mm hole

11051031 GS 15KL12 30/ 100 35 ml 2.8 mm GL25 12mm hole

11051040 GS 25KL12 54 /150 150 ml 3.5 mm GL45 12mm hole

11051041 GS 25KL20 54 / 150 150 ml 3.5 mm GL45 20 mm hole

Depending on your speciﬁc requirements, it is possible to expand the PT 1200 E drive with our

functional accessories. Our expert personnel will be happy to assist you and answer all the questions

you might have.

Order information and accessories.

Authorized extension of your system.

–

CARRYING CASE

ADAPTER

DRIVES

HOLDER SYSTEM AND STAND

Sales No. Product Description

11010025 PT 1200 E, 230 V EU-power cable and tabletop power supply (1.8m)

11010027 PT 1200 E, 230 V CH-power cable and tabletop power supply (1.8m)

11010028 PT 1200 E, 230 V UK-power cable and tabletop power supply (1.8m)

11010026 PT 1200 E, 100 – 120 V Power cable and tabletop power supply (1.8m)

Sales No. Product Description

11040006 HS 1200 E Stainless steel holder for drive unit, tabletop power supply, four dispersing

aggregates and two tools. Weight: 0.68 kg

11040007 ST-P 13 /320 Stainless steel plate stand with anti-slip mat made of silicone, with height-

adjustable holder for the drive and for fastening the base station.

Weight: 1.00kg

Sales No. Product Description

11040004 Carrying case Made of polypropylene (anthracite), with feet, continuous hinge, sturdy clip

closures and openings for drive unit, tabletop power supply, cables, and two

aggregates. Dimensions: 350 x 245 x100 mm /Weight (empty): 1.10 kg

Sales No. Product Description

11035002 Adapter PT-DA / PT-DA (E / C) This adapter connects older C-coupling dispersing aggregates such as

PT 1200 C/CL / B with E-coupling drive units.

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Kinematica

Kinematica

Kinematica Microtron System MB 800 Manual de usuario

Kinematica

Kinematica Megatron MT 5100 S2 Instrucciones de funcionamiento

Kinematica

Kinematica MEGATRON MT 3100 S2 Manual de usuario

Kinematica

Kinematica POLYTRON SYSTEM PT 1300 D Manual de usuario

Kinematica

Kinematica POLYTRON PT 6100 D Manual de usuario

Kinematica

Kinematica MICROTRON MB 550 Manual de usuario

Kinematica

Kinematica MICROTON SYSTEM MB 950 G Manual de usuario

Kinematica

Kinematica POLYTRON PT 2500 E Manual de usuario

Kinematica

Kinematica POLYMIX PX-MFC 90 D Manual de usuario

Kinematica

Kinematica POLYTRON PT 3100 D Manual de usuario

Kinematica

Kinematica Reactron System RT 1 Manual de usuario

Kinematica

Kinematica POLYTRON SYSTEM PT 1300 D Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario