Kikusui PLZ-U Series Manual de usuario

Part No. ZI-(X)2-982, IB004851

Feb. 2004

OPERATION MANUAL

ELECTRONIC LOAD PLZ-U Series

PLZ 70UA

PLZ 150U

PLZ -30F

PLZ -50F

Use of Operation Manual

Please read through and understand this Operation Manual before operating the product. After reading,

always keep the manual nearby so that you may refer to it as needed. When moving the product to another

location, be sure to bring the manual as well.

If you find any incorrectly arranged or missing pages in this manual, they will be replaced. If the manual it

gets lost or soiled, anew copy can be provided for afee. In either case, please contact Kikusui distributor/

agent, and provide the “Kikusui Part No." given on the cover.

This manual has been prepared with the utmost care; however, if you have any questions, or note any

errors or omissions, please contact Kikusui distiibutor/agent.

Reproduction and reprinting of this operation manual, whole or partially, without our permission is prohib-

ited.

Both unit specifications and manual contents are subject to change without notice.

Printed in Japan.

Power Requirements of this Product

Power requirements of this product have been changed and the relevant sections of the Operation

Manual should be revised accordingly.

(Revision should be applied to items indicated by acheck mark [71.)

Input voltage

The input voltage of this product is VAC,

and the voltage range is to VAC. Use the product within this range only.

Input fuse

The rating of this product’s input fuse is A, VAC, and .

^WARNING To avoid etectrical shock, always disconnect the power cord or turn off

the switch on the switchboard before attempting to check or replace the

fuse.

Use a fuse element having ashape, rating, and characteristics suitable

for this product. The use of afuse with adifferent rating or one that short

circuits the fuse holder may result in fire, electric shock, or irreparable

damage.

Power cord

The product is provided with power cords described below. If the cord has no power plug,

attach apower plug or crimp-style terminals to the cord in accordance with the wire colors

specified in the drawing.

^WARNING The attachment of apower plug or crimp-style terminals must be carried

out by qualified personnel.

Without apower plug

Blue (NEUTRAL)

Green/Yeliow (GND)

—Without apower plug

White (NEUTRAL)

IGreen or Green/Yellow (GND) j

Provided by Kikusul distributor/agent

Kikusul agents can provide you with suitable power cord.

For further information, contact Kikusul distributor/agent.

PLZ-U

ASafety Symbols

For the safe use and safe maintenance of this product, the following

symbols are used throughout this manual and on the product. Under-

stand the meanings of the symbols and observe the instructions they

indicate (the choice of symbols used depends on the products).

^OR AIndicates that ahigh voltage (over 1000 V) is used here. Touch-

ing the part causes apossibly fata! electric shock. If physical

contact is required by your work, start work only after you make

sure that no voltage is output here.

DANGER Indicates an imminently hazardous situation which, If ignored,

will result in death or serious injury.

^WARNING

Indicates apotentially hazardous situation which, if ignored,

could result in death or serious injury.

Indicates apotentially hazardous situation which, if ignored, may

result in damage to the product and other property.

Is placed before the sign "DANGER,” “WARNING,” or “CAU-

TION” to emphasize these. When this symbol is marked on the

product, see the relevant sections in this manual.

1Safety Symbols PLZ-U

ASafety Precautions

The following safety precautions must be observed to avoid fire hazard,

electrical shock, accidents, and other failures. Keep them in mind and

make sure that all of them are observed properly.

Users

•This product must be used only by qualified personnel who understand the con-

tents of this operation manual.

•If it is handled by disqualified personnel, persona! injury may result. Be sure to han-

dle it under supervision of qualified personnel (those who have electrical knowl-

edge.)

•This product is not designed or manufactured for general home or consumer use.

Purposes of use

•Do not use the product for purposes other than those described in the operation

manual.

Input power

•Use the product with the specified input power voltage.

•For applying power, use the power cord provided. Note tiiat the provided power

cord is not use with some products that can switch among different input power

voltages or use 100 Vand 200 Vwithout switching between them. In such acase,

use an appropriate power cord.

Fuse

•With products with afuse holder on the exterior surface, the fuse can be replaced

with anew one. When replacing afuse, use the one which has appropriate shape,

ratings, and specifications.

Cover

•There are parts inside the product which may cause physical hazards. Do not

remove the external cover.

PL2-U Safety Precautions HI

Installation

•When installing products be sure to observe 2.2, “Precautions Concerning Instal-

lation Location” described in this manual.

•To avoid electrical shock, connect the protective ground terminal to electrical

ground (safety ground).

•When connecting the power cord to aswitchboard, be sure work Is performed by

aqualified and licensed electrician or is conducted under the direction of such a

person.

«When installing products with casters, be sure to lock the casters.

Relocation

•Turn off the power switch and then disconnect all cables when relocating the

product.

*Use two or more persons when relocating the product which weights more than

20 kg. The weight of the products can be found on the rear panel of the product

and/or in this operation manual.

*Use extra precautions such as using more people when relocating into or out of

present locations including inclines or steps. Also handle carefully when relocat-

ing tall products as they can fail over easily.

•Be sure the operation manual be included when the product is relocated.

Operation

•Check that the AC input voltage setting and the fuse rating are satisfied and that

there is no abnormality on the surface of the power cord. Be sure to unplug the

power cord or stop applying power before checking.

•If any abnormality or failure is detected in the products, stop using it immediately.

Unplug the power cord or disconnect the power cord from the switchboard. Be

careful not to allow the product to be used before it is completely repaired.

•For output wiring or load cables, use connection cables with larger current capac-

ity.

•Do not disassemble or modify the product. If it must be modified, contact Kikusul

distributor/agent.

Maintenance and checking

•To avoid electrical shock, be absolutely sure to unplug the power cord or stop

applying power before performing maintenance or checking.

•Do not remove the cover when performing maintenance or checking.

•To maintain performance and safe operation of the product, it is recommended

that periodic maintenance, checking, cleaning, and calibration be performed.

Service

•Internal service is to be done by Kikusui service engineers. If the product must be

adjusted or repaired, contact Kikusui distributor/agent.

VSafety Precautions PLZ-U

For the safe use of equipment, IEC60664 (Insulation coordination for equipment

within low-voltage systems) classifies circuits into four categories by an occurrence

level of transient voltage. When you connect equipment to apower line or connect a

measuring instrument to these places, make sure of the applied overvoltage cate-

gory. This instrument is designed to operate from the overvoltage category II.

Overvoltage category I

Equipment of overvoltage category Iis equipment for connection to circuits in

which measures are taken to limit transient overvoltages to an appropriately low

level.

Examples are protected electronic circuits.

Overvoltage category II

Equipment of overvoltage category II is energy-consuming equipment to be sup-

plied from the fixed installation.

Examples of such equipment are appliances, portable tools and other household and

similar loads.

If such equipment is subjected to special requirements with regard to reliability and

availability, overvoltage category III applies.

Overvoltage category III

Equipment of overvoltage category III is equipment in fixed installations and for

cases where the reliability and the availability of the equipment is subject to special

requirements.

Examples of such equipment are switches in the fixed installation and equipment for

industrial use with permanent connection to the fixed installation.

Overvoltage category IV

Equipment of overvoltage IV is for use at the origin of the installation.

Example of such equipment are electricity meters and primary overcurrent protec-

tion equipment.

PLZ-U Overvoltage Category V

This Operation Manual is made up of the following sections.

Chapter 1General Description

This chapter gives an overview and describes the features of the PLZ-U.

Chapter 2Installation and Preparation

This chapter describes the procedures of unpacking and preparation before using the

PLZ-U.

Chapter 3Names and Functions of Parts

This chapter describes the names and functions of parts on the front and rear panels

of the frame and load unit.

Chapter 4Basic Operation

This chapter describes the operating procedure of each operation mode and other

basic functions.

Chapter 5Application Operation

This chapter describes functions such as ABC preset memories, switching function,

and sequence function that are used in actual applications.

Chapter 6Remote Control

This chapter describes the procedure for connecting the interface and the procedure

for transmitting commands to the PLZ-U using SCPI commands.

Chapter? Maintenance

This chapter explains the PLZ-U maintenance.

Chapter 8Specifications

This chapter lists the electrical and mechanical specifications of the PLZ-U.

Appendix

The appendices cover the operating area of the PLZ-U, the basic operation modes,

sequence program creation table, SCPI command reference, and error messages.

V! Arrangement of this manual PLZ-U

Contents

Power Requirements of this Product I

Safety Symbols li

Safety Precautions 111

Overvoltage Category V

Arrangement of this Manual VI

Chapter 1General Description ^

1.1 About This Manual 1-2

1.2 Product Overview -1-2

1.3 Features 1-3

1.4 Options 1-5

Chapter 2Installation and Preparation ^

2. 1Checking the Package Contents 2-2

2.1.1 Frame -2-2

2.1.2 Load Unit 2-3

2.2 Precautions Concerning Installation Location 2-4

2.3 Precautions When Moving the PLZ-U 2-5

2.4 Installing Load Units 2-6

2.5 Connecting the Power Cord 2-8

2.6 Grounding (Earth) '2-9

2.7 Power Up ,2-10

2.8 Load Wiring 2-12

2.8.1 Precautions Concerning Wiring 2-12

2.8.2 Connection to the Load Input Terminal on the Rear Panel 2-15

2.8.3 Connection to the Load Input Terminal on the Front Panel 2-17

Chapter 3Names and Functions of Parts 3-1

3.1 Front Panel 3-2

3.1.1 Frame 3-2

3.1.2 Load Unit (Channel) 3-8

3.2 Rear Panel -3-11

Chapter 4Basic Operation ^

4.1 Panel Control Basics -4-2

4.2 Load On/Off -4-3

4.3 Basic Operation --4-5

4.4 Protection Functions and Alarms 4-7

4.4. 1Protection Function 4-7

4.4.2 Alarms 4-8

4.4.3 Setting the Trip Points 4-10

PLZ-U Contents VII

Chapter 5Application Operation 5-1

5.1 Soft Start Function -5-2

5.2 ABC Preset Memories 5-3

5.3 Switching Function 5-5

5.4 Setting the Slew Rate 5-7

5.5 Elapsed Time Display and Auto Load Off Timer 5-8

5.6 Sequence Function 5-9

5.6. 1Editing the Sequence 5-9

5.6.2 Executing the Sequence 5-1

5.6.3 Example Sequence 5-13

5.7 Remote Sensing Function -5-15

5.8 Key Lock Function 5-16

5.9 Configuration Settings 5-17

5.10 External Control 5-21

5.10.1 FRAME CONT Connector - - -5-21

5.10.2 CH CONT Connector 5-25

5.11 Parallel Operation 5-28

5.12 Setup Memories 5-30

5.13 Factory Default Settings 5-31

5.13.1 Factory Default Settings (General) 5-32

5. 13.2 Factory Default Settings of ABC Preset Memories -5-33

5.13.3 Factory Default Settings of Setup Memories 5-33

Chapter 6Remote Control 6-1

6. 1Overview 6-2

6.2 Instrument Interface Standard 6-2

6.3 Using SCPI Commands 6-3

6.3.1 Hierarchy of SCPI Commands -6-3

6.3.2 Parameter Format 6-6

6.4 Interface Setup 6-10

6.4.1 GPIB Control ---6-10

6.4.2 RS-232C Control - - -6-11

6.5 SCPI Commands 6-13

6.5.1 IEEE 488.2 Common Commands 6-13

6.5.2 Channel Commands -6-17

6.5.3 Measurement Commands —6-18

6.5.4 Configuration and Operation Commands 6-19

6.5.5 Trigger Commands -6-24

6.5.6 Switching Function Commands 6-26

6.5.7 Input State Commands —-6-27

6.6 Status Registers 6-33

6.6. 1SCPI Registers 6-33

6.6.2 IEEE488.2 Registers 6-50

VIII Contents PLZ-U

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de Kikusui

Kikusui

Kikusui PFX2731S Manual de usuario

Kikusui

Kikusui TOS5101 Manual de usuario

Kikusui

Kikusui TOS3200 Manual de usuario

Kikusui

Kikusui HP21-TOS Manual de usuario

Kikusui

Kikusui tos6200 Manual de usuario

Kikusui

Kikusui PLZ-5WH2 Series Manual de usuario

Kikusui

Kikusui COS5060 Manual de usuario

Kikusui

Kikusui TT21-KES Manual de usuario

Kikusui

Kikusui DSI1020 Manual de usuario

Kikusui

Kikusui PFX2500 Series Manual de usuario

Kikusui

Kikusui TOS5300 Manual de uso y cuidado

Kikusui

Kikusui TOS5050A Manual de usuario

Kikusui

Kikusui PFX2000 Series Manual de usuario

Kikusui

Kikusui LIN Series Manual de usuario

Kikusui

Kikusui tos6200 Manual de usuario

Kikusui

Kikusui 5040 Manual de usuario

Kikusui

Kikusui COS5040 Manual de usuario

Kikusui

Kikusui TOS5200 Manual de usuario

Kikusui

Kikusui TOS9200 Manual de usuario

Kikusui

Kikusui TOS3200 Manual de usuario

Kikusui

Kikusui OT03-PCR-WEA Manual de usuario

Kikusui

Kikusui TOS5200 Manual de usuario

Kikusui

Kikusui HP01A-TOS Manual de usuario

Kikusui

Kikusui TOS5200 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario