Kidde Fire Systems
400 Main Street
Ashland, MA 01721
Ph: 508.881.2000
Fax: 508.881.8920
www.kiddefiresystems.com
KIDDE is a registered trademarks of Kidde-Fenwal, Inc. or its parents, subsidiaries or affiliates.
3M and Novec are trademarks of the 3M Company.
This literature is provided for informational purposes only. KIDDE-FENWAL, INC. believes this data to be accurate, but it is published and presented without any guarantee
or warranty whatsoever. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The fire suppression system design,
installation, maintenance, service and troubleshooting must be performed by trained, authorized Kidde Fire Systems distributors for the product to work correctly.
If you need more information on this product, or if you have a particular problem or question, contact:
KIDDE-FENWAL, INC., Ashland, MA 01721 USA, Telephone: (508) 881-2000.
K-45-9144 Rev AB
©2018 Kidde-Fenwal, Inc.
2
EXPORT INFORMATION (USA)
Jurisdiction: EAR
Classification: EAR99
This document contains technical data subject to the EAR.
MAINTENANCE
According to NFPA standards the following inspection
and/or maintenance procedure must be scheduled as
listed below and performed upon the occurrence of any
event which might affect the reliability of the system.
QUARTERLY INSPECTION
1. Check the pressure gauges of each agent storage
container. If the pressure gauge indicates a loss in
pressure of 10% or more, then it shall be recharged
or replaced. Pressure varies with temperature, and
this must be taken into account when checking the
pressure gauge.
2. Check all components, including supporting hard-
ware, and tighten, repair or replace as required.
3. Replace any component if at all in doubt of its ability
to perform properly.
SEMI-ANNUAL INSPECTION
Qualified personnel are to determine the amount of agent
in all containers. The optional liquid level indicator may
be used to measure agent supply and compare it to the
original net weight which is marked on the container
label. If the measured net weight is less than 95% of the
original charged weight the container should be
recharged or replaced.
Inspect all piping, fittings and nozzles for looseness, dirt
or other damage. All outlet piping must be clean and free
of dirt, chips, fillings and other foreign material that may
cause the system to become inoperative or ineffective at
the time of discharge.
SPECIFICATIONS
DIMENSIONS
ORDERING INFORMATION
Fill Range 455-910 lb.
(206.4-412.8 kg)
Height 70 in.
(1789 mm)
Diameter 24 in.
(610 mm)
Internal Volume 13 ft.3
(0.368 m3)
Empty Weight 505 lb.
(229 kg)
Temperature Range 0°F to 130°F
(-18°C to 54°C)
Safety Relief Burst Range 800 to 975 PSIG
(5.5 to 6.7 Mpa)
Construction Specification DOT 4BW-500
Description Part Number
900 lb. Cylinder with Liquid Level Indicator 45-200901-001
900 lb. Cylinder without Liquid Level Indicator 45-200900-001
Accessories
3-inch stainless steel flexible hose 06-118225-001
3-inch swing check valve 06-118058-001
Cylinder bracket 06-236125-001
Cylinder cradle 06-118300-001
Cylinder supervisory pressure switch 06-118262-001*
*For cylinder valves manufactured prior to May 1, 2013 use super-
visory pressure switch P/N: 06-118263-001.
VALVE ORIENTATION
PLAN VIEW
SAFETY BURST
DISC ASSEMBLY
24 in.
(610 mm)
70 in.
(1789 mm)
62 in.
(1566 mm)
