Kidde Fire Systems PEGAsys Manual de usuario

UL Listing File No. S2422

Factory Mutual Approval J.I. No. OB2A6.AY

LISTED

Fire Systems

August 1999

P/N 76-100016-001

PEGAsys

Intelligent Suppression-Control

and Fire-Alarm System

Installation, Operation,

and Maintenance Manual

Document No. PEGAsys

August 1999

PEGAsys

Intelligent Suppression-Control

and Fire-Alarm System

Installation, Operation,

And Maintenance Manual

This Manual Is To Be Used By Trained Distributors Only

FOREWORD

This manual is intended to clearly and accurately reflect the PEGAsys Fire Alarm/Suppression Control System. This publication de-

scribes the operation, installation and maintenance of the PEGAsys Fire Alarm/Suppression Control System, P/Ns 76-100000-501 for

Single-Loop System and 76-100000-600 for Multi-Loop System.

TERMS AND ABBREVIATIONS

ADA Americans with Disabilities Act

AI Addressable Contact Input Device

AO Addressable Relay Output Device

BPM Beats Per Minute

CCM Central Control Module

CCP Central Control Panel

EDP Electronic Data Processing

EOC Event Output Control

FCP Fire Control Panel

GUI Graphical User Interface

I/O Input/Output

ID Identification

IRI Industrial Risk Insurers

NC Normally Closed

NO Normally Open

NR Not Registered

NYC New York City

P/N Part Number

PAS Positive Alarm Sequence

PC Personnel Computer

PCS PEGAsys Configuration Software

PC Line Power/Communication Line (RX/TX Loop)

PS Power Supply

RCU Remote Control Unit

RTC Real Time Clock

RX/TX Receive Transmit

UL Underwriter Laboratories

VDC Voltage Direct Current

ACCEPTANCES, APPROVALS, AND CERTIFICATIONS

PEGAsys Single-Loop System (P/N 76-100000-501)

• UL: Underwriter’s Laboratories Listing File Number S2422.

• FM: Factory Mutual Engineering Corp. (Factory Mutual System) Approval J.I. Number 3005511

• CSFM: Pending.

• NYC: Pending.

PEGAsys Multi-Loop System (P/N 76-100000-600)

• UL: Underwriter’s Laboratories Listing File Number S2422.

• FM: Factory Mutual Engineering Corp. (Factory Mutual System) Approval J.I. Number 3005511

• CSFM: Pending.

• NYC: Pending.

(THIS PAGE IS INTENTIONALLY LEFT BLANK)

iii

TABLE OF CONTENTS

Forward ......................................................................................................................................................... i

Terms and Abbreviations ................................................................................................................................i

Appendices ................................................................................................................................................... vi

List of Illustrations .......................................................................................................................................... vii

List of Tables ................................................................................................................................................. ix

Safety Summary ............................................................................................................................................ x

PARAGRAPH TITLE PAGE

1 GENERAL INFORMATION ................................................................................................................................................1-1

1-1 Introduction ..................................................................................................................................................................... 1-1

1-1.1 System Description ........................................................................................................................................................1-1

1-1.2 System Components .....................................................................................................................................................1-1

1-2 Component Description .................................................................................................................................................1-1

1-2.1 Central Control Module (CCM) .......................................................................................................................................1-1

1-2.2 Display Module ...............................................................................................................................................................1-1

1-2.3 Receiver/Transmitter Module (RX/TX) ............................................................................................................................1-2

1-2.4 Power Supply/Charger Assembly ..................................................................................................................................1-2

1-2.5 Basic Motherboard .........................................................................................................................................................1-2

1-2.6 Multi-Loop Motherboard .................................................................................................................................................1-3

1-2.7 Input/Output Modules .....................................................................................................................................................1-3

1-2.7.1 Signal Output Module ..................................................................................................................................................... 1-3

1-2.7.2 Relay Output Module ......................................................................................................................................................1-3

1-2.7.3 Agent Release Output Module .......................................................................................................................................1-4

1-2.7.4 City Tie Module ............................................................................................................................................................... 1-4

1-2.8 Standby Batteries ............................................................................................................................................................1-4

1-2.9 Intelligent Loop Devices .................................................................................................................................................1-4

1-2.9.1 SmartOneTM Ionization Detectors ...................................................................................................................................1-4

1-2.9.2 SmartOne Photoelectric Detectors ................................................................................................................................1-5

1-2.9.3 SmartOne Heat Detectors .............................................................................................................................................1-5

1-2.10 SmartOne Detector Bases ............................................................................................................................................1-5

1-2.11 Addressable Contact Input Devices ..............................................................................................................................1-5

1-2.12 Addressable Relay Output Devices ...............................................................................................................................1-5

1-2.13 Model DH-2000 Air Duct Housing ..................................................................................................................................1-5

1-2.14 Loop Isolator Devices ....................................................................................................................................................1-6

1-3 System Specification ......................................................................................................................................................1-6

2 OPERATION ....................................................................................................................................................................2-1

2-1 Introduction ..................................................................................................................................................................... 2-1

2-1.1 Mode of Operation ..........................................................................................................................................................2-1

2-2 Control and Indicators ....................................................................................................................................................2-1

2-2.1 LCD Display ................................................................................................................................................................... 2-1

2-2.2 Audible Device ................................................................................................................................................................2-2

2-2.3 Control and Indicator Description ..................................................................................................................................2-2

2-3 System Security ..............................................................................................................................................................2-2

2-3.1 Levels of Security ............................................................................................................................................................2-2

2-3.2 Default Passwords .........................................................................................................................................................2-2

2-3.3 Entering Passwords ......................................................................................................................................................2-2

2-4 System Power-Up ..........................................................................................................................................................2-2

2-5 System Menus ................................................................................................................................................................2-4

2-5.1 Menu Structure ................................................................................................................................................................2-4

2-5.2 Accessing the System Menus ........................................................................................................................................2-4

2-5.3 Exiting the System Menus ..............................................................................................................................................2-4

2-5.4 Menu Functions ..............................................................................................................................................................2-4

2-5.4.1 Isolate Menu Function ....................................................................................................................................................2-4

2-5.4.2 List Menu Function .........................................................................................................................................................2-4

2-5.4.3 Set Menu Function ..........................................................................................................................................................2-4

2-5.4.4 Test Menu Function ........................................................................................................................................................2-4

2-6 Modes of Operation ........................................................................................................................................................2-5

2-6.1 Normal Standby Mode ....................................................................................................................................................2-5

2-6.2 Active Alarm Mode ...........................................................................................................................................................2-5

2-6.2.1 Alarm Mode Indications ..................................................................................................................................................2-5

2-6.2.2 Alarm Mode User Action .................................................................................................................................................2-5

2-6.3 Active Supervisory Trouble Mode ................................................................................................................................. 2-10

2-6.3.1 Supervisory Trouble Mode Indication ........................................................................................................................... 2-10

2-6.3.2 Supervisory Trouble Mode User Action ........................................................................................................................ 2-10

2-6.4 Active Trouble Mode ...................................................................................................................................................... 2-11

2-6.4.1 Trouble Mode Indications .............................................................................................................................................. 2-11

2-6.4.2 Trouble Mode User Action ............................................................................................................................................. 2-11

2-7 Printing Operation ......................................................................................................................................................... 2-11

2-8 System Programming ................................................................................................................................................... 2-11

2-8.1 EOC Programming ........................................................................................................................................................ 2-11

2-8.1.1 Listing EOC Programming ........................................................................................................................................... 2-12

2-8.2 RTC Programming ....................................................................................................................................................... 2-12

2-8.2.1 Listing RTC Programming ........................................................................................................................................... 2-12

2-8.2.2 Enable/Disable RTC Program Line Numbers ............................................................................................................ 2-12

2-8.3 Types of Inputs and Outputs ........................................................................................................................................ 2-12

2-8.3.1 System Inputs ............................................................................................................................................................... 2-12

2-8.3.2 Remote Control Unit (RCU) ......................................................................................................................................... 2-12

2-8.3.3 RX/TX Loops ................................................................................................................................................................. 2-12

2-8.3.4 System Outputs ............................................................................................................................................................ 2-13

2-8.3.5 System I/O Modules ..................................................................................................................................................... 2-13

2-8.4 Addressing I/O Modules ............................................................................................................................................... 2-13

2-8.5 Registering I/O Module Assignments .......................................................................................................................... 2-13

2-8.5.1 Listing I/O Module Assignment .................................................................................................................................... 2-13

2-8.6 Addressing RCU’s ....................................................................................................................................................... 2-13

2-8.7 Registering RCU’s ....................................................................................................................................................... 2-14

2-8.7.1 Detector Registration ................................................................................................................................................... 2-14

2-8.7.2 Addressable Contact Monitor Registration .................................................................................................................. 2-14

2-8.7.3 Remote Relay Registration .......................................................................................................................................... 2-15

2-8.7.4 Listing all Registered RCU’s ....................................................................................................................................... 2-15

2-8.7.5 Un-registering RCU’s .................................................................................................................................................. 2-15

3 FUNCTIONAL DESCRIPTION .......................................................................................................................................... 3-1

3-1 Introduction ..................................................................................................................................................................... 3-1

3-2 Overall Block Diagram Description ................................................................................................................................3-1

3-3 Functional Descriptions ................................................................................................................................................. 3-2

3-3.1 Central Control Module ..................................................................................................................................................3-2

3-3.2 Receiver/Transmitter (RX/TX) Module ............................................................................................................................ 3-3

3-3.3 Power Supply/Charger Assembly, Revision A ................................................................................................................ 3-4

3-3.4 Power Supply/Charger Assembly, Revision C ............................................................................................................... 3-5

3-3.5 Multi-Loop I/O Motherboard ............................................................................................................................................ 3-6

3-3.6 Signal Output Module ..................................................................................................................................................... 3-7

3-3.7 Relay Output Module ...................................................................................................................................................... 3-8

3-3.8 Agent Release Module ................................................................................................................................................... 3-9

3-3.9 City Tie Module ............................................................................................................................................................. 3-10

3-3.10 Field Devices ................................................................................................................................................................. 3-11

3-3.11 SmartOne Ionization Detectors .................................................................................................................................... 3-11

3-3.12 SmartOne Photoelectric Detectors ............................................................................................................................... 3-11

3-3.13 SmartOne Heat Detectors ............................................................................................................................................ 3-11

3-3.14 Addressable Contact Input Devices ............................................................................................................................. 3-11

3-3.15 Addressable Relay Output Devices ............................................................................................................................. 3-12

3-3.16 Model DH-2000 Air Duct Housing ................................................................................................................................ 3-12

3-3.17 Loop Isolator Devices .................................................................................................................................................. 3-12

4 MAINTENANCE PROCEDURE ......................................................................................................................................... 4-1

4-1 Introduction ..................................................................................................................................................................... 4-1

4-2 Scheduled Maintenance ................................................................................................................................................ 4-1

4-3 Maintenance Procedures ............................................................................................................................................... 4-1

4-3.1 Lamp Test ....................................................................................................................................................................... 4-1

4-3.2 Loop Device Test ............................................................................................................................................................ 4-1

4-3.3 Battery Test ..................................................................................................................................................................... 4-1

4-3.4 Walk Test ........................................................................................................................................................................ 4-2

TABLE OF CONTENTS (CONT.)

PARAGRAPH TITLE PAGE

4-3.4.1 Walk Testing Detectors ..................................................................................................................................................4-2

4-3.4.2 Walk Test Procedure ......................................................................................................................................................4-2

4-3.5 Alarm Simulation Test (AST) ..........................................................................................................................................4-2

4-3.5.1 AST Procedure ...............................................................................................................................................................4-3

4-4 Disarming and Rearming Release Circuits .................................................................................................................. 4-3

4-4.1 Disarming Release Circuits ..........................................................................................................................................4-3

4-4.2 Arming Release Circuits ................................................................................................................................................4-3

4-5 Power-Down System ......................................................................................................................................................4-3

4-5.1 Power-Down Procedure .................................................................................................................................................4-3

4-6 Power-Up System ..........................................................................................................................................................4-4

4-6.1 Power-Up Procedure ......................................................................................................................................................4-4

5 TROUBLESHOOTING AND CORRECTIVE MAINTENANCE ............................................................................................. 5-1

5-1 Introduction ..................................................................................................................................................................... 5-1

5-2 Standard Fault Isolation Techniques .............................................................................................................................5-1

5-2.1 Visual Inspection ............................................................................................................................................................5-1

5-2.2 Power Checks ................................................................................................................................................................5-1

5-3 Troubleshooting .............................................................................................................................................................5-1

5-4 Removal and Replacement ...........................................................................................................................................5-2

5-4.1 Required Tools ............................................................................................................................................................... 5-2

5-4.2 Central Control Module ..................................................................................................................................................5-2

5-4.3 RX/TX Module .................................................................................................................................................................5-2

5-4.4 Field Devices ..................................................................................................................................................................5-3

6 PARTS LIST ....................................................................................................................................................................6-1

6-1 Introduction ..................................................................................................................................................................... 6-1

7 INSTALLATION ................................................................................................................................................................7-1

7-1 Introduction ..................................................................................................................................................................... 7-1

7-2 Materials Required For Installation ................................................................................................................................7-1

7-3 Installation Procedure For Central Control Panel .........................................................................................................7-1

7-4 Installation Procedure For Expansion Enclosures ........................................................................................................7-1

7-5 Installation Procedure For I/O Motherboard ...................................................................................................................7-2

7-6 Installation Procedure For Rx/Tx Module (Multi-Loop Only) ...........................................................................................7-2

7-7 Installation of I/O Modules ..............................................................................................................................................7-3

7-7.1 Signal Audible Output Module ........................................................................................................................................7-3

7-7.2 Relay Output Module ......................................................................................................................................................7-4

7-7.3 Agent Release Module ...................................................................................................................................................7-4

7-7.4 City-Tie Output Module ...................................................................................................................................................7-4

7-7.6 Power Supply/Charger Assembly ..................................................................................................................................7-4

7-7.7 Power Supply/Charger Assembly, Expansion Enclosure ..............................................................................................7-4

7-7.8. Power Supply Communication Connections ................................................................................................................ 7-6

7-8 Connecting AC Power ....................................................................................................................................................7-6

7-9 Install And Connect DC Power .......................................................................................................................................7-6

7-9.1 Battery Enclosure ...........................................................................................................................................................7-6

7-9.2 Batteries .........................................................................................................................................................................7-6

7-10 Field Device Connection To RX/TX Module ....................................................................................................................7-7

7-10.1 Wiring the RX/TX PC Line ...............................................................................................................................................7-7

7-11 Output Signal Connection ..............................................................................................................................................7-9

7-12 External Power Failure Indicator Connection .............................................................................................................. 7-10

7-13 Detector Installation ..................................................................................................................................................... 7-10

7-14 Setting and Adjusting Smoke & Heat Detector Sensitivities ........................................................................................ 7-10

7-14.1 Setting and Adjusting Smoke and Heat Detector Sensitivity Procedure ..................................................................... 7-10

7-15 Addressable Contact Input Device Installation ............................................................................................................. 7-11

7-16 Addressable Relay Output Device Installation ............................................................................................................. 7-11

7-17 Installation Checkout ..................................................................................................................................................... 7-11

7-18 Connection of Peripherals ............................................................................................................................................ 7-11

7-18.1 Connecting a Terminal or Personal Computer ............................................................................................................ 7-11

7-18.2 Connecting a Printer ..................................................................................................................................................... 7-11

TABLE OF CONTENTS (CONT.)

PARAGRAPH TITLE PAGE

A POWER SUPPLY REQUIREMENTS .............................................................................................................................. A-1

B SYSTEM EXPANSION .................................................................................................................................................... B-1

C RELEASING APPLICATIONS ......................................................................................................................................... C-1

D NOT USED .................................................................................................................................................................... D-1

E FACTORY MUTUAL SPRINKLER REQUIREMENTS .................................................................................................... E-1

F GLOSSARY ..................................................................................................................................................................... F-1

G DISPLAY ABBREVIATIONS ............................................................................................................................................ G-1

H INDEX ............................................................................................................................................................................ H-1

I SYSTEM DRAWINGS ...................................................................................................................................................... I-1

J PEGAsys NETWORK INTERFACE CARD ...................................................................................................................... J-1

K ADDRESSABLE SIGNAL/SOUNDER ............................................................................................................................ K-1

L REMOTE DISPLAY CONTROL MODULE AND REMOTE DISPLAY MODULE ...............................................................L-1

M ADDRESSABLE ALARMLINE MODULE ........................................................................................................................ M-1

N NETWORKABLE CENTRAL CONTROL MODULE (NCCM) ......................................................................................... N-1

O CENTRAL STATION OPERATION .................................................................................................................................. O-1

APPENDICES

APPENDIX TITLE PAGE