Kicker SoundGate SWRA411 Manual de usuario

Designed for 2011 and newer Jeep Wrangler vehicles

SWRA411

T-TAP x2

10MM BOLT

FUSE 25 AMP

WIRE TIES x6

SUBWOOFER ASSEMBLY

200 WATT AMP

POWER HARNESS

OVERLAY HARNESS

Fig. 3

Fig. 1

Fig. 4

Fig. 5

Amp Installation

1. Disconnect the negative battery cable.

2. Gently pull out on the panel just below the steering column, rotate down and remove. Fig. 1

3. Remove the two 7mm screws securing the plastic panel below the steering column indicated by the

arrow in Fig. 2 , and the one 7mm screw near the kick panel. Also, remove the two 10mm bolts

securing the metal plate and remove plate.

4. Remove the dash end panel by prying loose with a panel removal tool. Fig. 3

5. Install the amp into position by lining up the holes in the amp bracket with the two holes for the bolts

that retained the metal plate. Fig. 4

6. Install the supplied 10mm bolt into the bottom hole and leave loose. Fig. 5

7. Reinstall the metal plate over the top of the amp bracket and replace the factory bolts and tighten.

8. Tighten the bottom bolt.

Fig. 2

Fig. 6 Fig. 7

Fig. 8 Fig. 9

Wire Harness Installation

9. Find the rubber grommet in the top driver’s side of the fire wall underneath the hood and remove it.

Fig. 6

10.Using a razor knife make a small cut in the center of the grommet. Pass the end of the wire with the

small terminal on the end through the grommet and pull the grommet up to the point where the plastic

sheathing starts. Fig. 7

11.Run the wire through the grommet hole in the fire wall and reinstall the grommet.

12.Run the wire along the top of the fire wall toward the battery and secure with wire ties.

13.Remove the top of the fuse cover and using a 13mm socket and ratchet loosen and remove the nut

on the positive battery accessory lug. Fig. 8

14.Connect the ring terminal of the power harness to the lug and retighten the nut. Torque to 10Nm.

15.Using a panel removal tool remove the four plastic retainers (three in front door opening and one in

rear door opening) securing the driver’s side sill plate and B pillar post cover. Fig. 9

16.Gently pull the kick panel/sill plate toward the brake pedal to release the fasteners securing it.

17.Connect the ten pin connector of the harness to the amplifier. Slide the red locking tab over to

prevent the connector from accidentally coming disconnected.

18.Route the harness along the bottom of the front and rear door jam and toward the back seat.

Subwoofer input connection without optional amplifier installed

19.Locate the left front lower dash speaker wires on the back of the plastic speaker housing. The wire

colors are gray with a yellow stripe and gray with a purple stripe. Fig. 9

Fig. 10

Fig. 11

20.Install one of the self stripping t-tap connectors on to each wire. Lay the wire in the open channel, fold

the connector body over and squeeze with a pair of pliers until connector snaps shut. Fig. 10

21.Connect the subwoofer harness input wires to the t-tap connectors. The green wire (positive) of the

harness connects to the t-tap connector on the gray wire with the yellow stripe in the vehicle. The

brown wire (negative) of the harness connects to the t-tap connector on the gray wire with the purple

stripe in the vehicle.

Subwoofer input connection with optional five-channel amplifier installed

22.Connect the green wire of the of the subwoofer harness to the green wire of the 4.1 amplifier harness.

Connect the brown wire of the subwoofer harness to the brown wire of the 4.1 amplifier harness.

Subwoofer input connection for Premium Audio vehicles with factory eight-channel amplifier installed

23.Locate the 16 pin connector on the amplifier behind the left front speaker housing. Find the

green/brown stripe wire and the gray/brown strip wire in this connector and install one of the self

stripping t-tap connectors on to each wire. Lay the wire in the open channel, fold the connector body

over and squeeze with a pair of pliers until connector snaps shut. Fig. 10

24.Connect the green wire of the subwoofer harness to the gray/brown strip wire. Connect the brown

wire of the subwoofer harness to the green/brown stripe wire.

25.Install the supplied two pin connector by inserting the terminal on the end of the power wire into the

back of the connector until it clicks and locks. Fig. 11

26.Depress the blue terminal retainer down in the center of the connector.

27.Remove the bolt securing the support brace under the steering column and connect the ground wire

as shown in Fig. 12. Torque to 8Nm.

28.Run the wire harness along the floor under the rear seats to approximately the middle of the vehicle

and pull the end of the harness under the seat to the cargo area. Fig. 13

Fig. 12

Fig. 13 Fig. 14

29.Set the subwoofer in place and connect the wire harness.

30.Rotate the rear seat back until it is nearly vertical. While holding the seat back with one hand, slide the

enclosure back until the hooks on the bracket are centered under the anchor points at the bottom of

the seat. Slowly rotate the seat back toward the rear of the vehicle until it locks into place. Fig. 14

31.Reinstall all previously removed parts in reverse order.

32.Install supplied fuse in the fuse holder under hood.

33.Reconnect the negative battery cable. Torque to 5Nm.

Troubleshooting the KICKER Integrated Systems

If you experience a problem once the Subwoofer is installed use this guide to locate the trouble.

The radio is working, but the Subwoofer is not working:

xCheck the battery voltage to make sure it is not discharged below 11 volts.

xCheck the negative battery cable to see if it has been securely tightened back on the battery.

xCheck the inline fuse located near the battery to make sure it is plugged in completely, and not blown.

xCheck the inline +12Volt power-connector near the firewall to make sure it is plugged in securely.

xCheck the inline connectors near the subwoofer enclosure to make sure they are plugged securely.

xCheck the ground wire connection to make sure it is tightly secured to the proper ground in the

vehicle.

xCheck the audio input signal connection to make sure it is securely connected to the correct wiring.

xTest with different music if there is no low frequency audio in the initial sound check.

There is a buzz or rattle noise that accompanies the

low frequency element of the music:

xCheck for a connector or any other object that could be very near the subwoofer or the enclosure.

xCheck the subwoofer enclosure mounting brackets to make sure they are secure.

There is a problem with the multi-channel stereo amplifier:

xCheck the battery voltage to make sure it is not discharged below 11 volts.

xCheck the negative battery cable to see if it has been securely tightened back on the battery.

xCheck the inline fuse located near the battery to see if it is plugged in completely and not blown.

xCheck the multi-pin connectors at the back of the radio and at the amplifier chassis to make sure they

are plugged all the way in.

xCheck the ground wire connection to make sure it is tightly secured to the proper ground in the

vehicle.

Symptom

Possible Cause

Solution

No Subwoofer Output

Fuse not installed in inline

fuse holder on subwoofer

and/or amp harness

Install fuse(s) into fuse holder(s). Refer to

instructions for correct placement

Low battery voltage Recharge the battery

Negative battery cable not

connected Reconnect negative battery cable

Power wire connector not

connected to body harness

Connect power wire to body harness. Check

for loose connection

Ground wire not grounded

properly

Check ground wire with voltmeter to insure it is

a good ground

Signal input connector not

connected properly

Connect signal wire of subwoofer harness to

signal wire of amplifier harness or factory

speaker wire depending on application.

Check for loose connection

Balance or fader controls not

set to neutral position

Set balance and fader control to center

settings. (only affects stand alone subwoofer

kit)

No low frequency

information in music Test with several different songs

Subwoofer harness not

properly/completely

connected to subwoofer.

Securely fasten both of the connectors on the

subwoofer harness to the subwoofer. Check

for loose connections.

Radio not coming on

Radio connector not

properly/completely

connected

Check radio connector to insure it is

completely seated

Blown radio fuse Refer to owner's manual for radio fuse location

and value

Low battery voltage Recharge the battery

Radio comes on, but no

sound from any speakers

Fuse not installed in inline

fuse holder on amplifier

harness

Install fuse into fuse holder. Refer to

instructions for correct placement

Radio connector not

properly/completely

connected

Check radio connector to insure it is

completely seated

Ground wire not grounded

properly

Check ground wire with voltmeter to insure it is

a good ground

Low battery voltage Recharge the battery

If you continue to experience problems after troubleshooting with this list, please contact KICKER Technical Support at

(800) 256-0808 ext. 6009, or support@kicker.com.

0/"OXs3TILLWATER/KLAHOMAs53!s–8510

IMPORTANT:

Please

note

that

the

stated

fuse

ratings

included

the

instructions

are

incorrect.

The

fuse(s)

included

this

kit

are

rated

30A.

Remember

also

place

your

warranty

card

the

glove

box

for

future

use.

lfjrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKER(fKICKER(fKICKER(fKICKERr.

Limited

Warranty

SWRA411

fOUnD

fl:.OgEfT.

by(fKICKER

Audio

System

Upgrade

Please retain

this

card and

your

receipt with vehicle

Contains valuable information should you need service

Ill

II§

~1:13)1~/JI

JJI:I3JI~IJI

JJ1:13JI~IJI JJI:I3JI~IJI

JJI:I3JI~IJI

JJI:I3JI:JIJIJJI:I3JI:JIJIJJI:I3JI:JIJI

JJ91

Tabla de contenidos

Otros manuales de Subwoofer de Kicker

Kicker

Kicker Q-CLASS CompQ12 Manual de usuario

Kicker

Kicker CompVR DCVR10 Manual de usuario

Kicker

Kicker CompC Series Manual de usuario

Kicker

Kicker CompVT CVT12 Manual de usuario

Kicker

Kicker Solo-Baric C-Series Manual de usuario

Kicker

Kicker COMP8 Manual de usuario

Kicker

Kicker CompVR CVR12 Manual de usuario

Kicker

Kicker PTRTP Manual de usuario

Kicker

Kicker L7R Series Manual de usuario

Kicker

Kicker CompVT CVT12 Manual de usuario

Kicker

Kicker L7QB8 Manual de usuario

Kicker

Kicker CompVR CVR8 Manual de usuario

Kicker

Kicker PWRA2P07 Manual de usuario

Kicker

Kicker SOLO-BARIC S15L7 Manual de usuario

Kicker

Kicker KM12 Manual de usuario

Kicker

Kicker COMP12D4 Manual de usuario

Kicker

Kicker S18XSP Manual de usuario

Kicker

Kicker COMPVT65 Manual de usuario

Kicker

Kicker SOLO-BARIC S15L7 Manual de usuario

Kicker

Kicker Impulse 10i Manual de usuario

Kicker

Kicker Solo-Baric L7-Series Manual de usuario

Kicker

Kicker Solo-Baric S10L5 Manual de usuario

Kicker

Kicker CompVX CVX10 Manual de usuario

Kicker

Kicker PWRA215 Manual de usuario

Manuales populares de Subwoofer de otras marcas

Sony

Sony XS-AW8 Manual de usuario

Sony

Sony XS-L836 Manual de usuario

B&C Speakers

B&C Speakers 15 HPL 76W Manual de usuario

Velodyne

Velodyne DD-18+ Manual de usuario

Sonance

Sonance Cinema Series SUB 10-150 Manual de usuario

Hifonics

Hifonics HW-12 Guía de inicio rápido

Magnat Audio

Magnat Audio ADR 130 BP Manual de usuario

Blitz

Blitz BZP106 Manual de usuario

Technics

Technics SB-AS500 Manual de usuario

Lyngdorf

Lyngdorf BW-2 Manual de usuario

Lyngdorf

Lyngdorf BW-3 Manual de usuario

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manual de usuario

REL Acoustics

REL Acoustics Q Series Manual de usuario

Pioneer

Pioneer Elite S-W1EX Manual de usuario

L-Acoustics

L-Acoustics KIVA SB15M Guía de inicio rápido

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manual de usuario

KEF

KEF KUBE 200 Manual de usuario

Yamaha

Yamaha SW500 Manual de usuario