Kichler Lighting Select Dorset Manual de usuario
1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local
electrical codes. Electrical installation
should be performed by a qualified
licensed electrician.
3. WARNING: Not suitable for use with
solid-state speed controls.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box
for mounting to the outlet box. Most outlet
boxes commonly used for the support of
lighting fixtures are not acceptable for fan
support and may need to be replaced,
consult a qualified electrician if in doubt.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use only CUL Listed outlet boxes
marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. Do not operate reversing switch while fan
blades are in motion. Fan must be turned
off and blades stopped before reversing
blade direction.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After marking electrical connections,
spliced conductors should be turned
upward and pushed carefully up into
outlet box. The wires should be spread
apart with the grounded conductor and
the equipment-grounding conductor on
one side of the outlet box.
12. Electrical diagrams are reference only.
Light kits that are not packed with the fan
must be CUL Listed and marked suitable
for use with the model fan you are
installing. Switches must be CUL General
Use Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT
FAN TO OUTLET BOX MARKED
"ACCEPTABLE FOR FAN SUPPORT".
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT
OBJECTS IN THE PATH OF THE BLADES.
1
1. SAFETY RULES
2
3. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a. Fan blades (5)
b. Mounting plate
c. Fan motor assembly
d. Motor housing
e. Set of 5 blade brackets and Pre-Installed
mounting screws
f. Mounting plate
g. Light kit
h. Glass shade
i. 40W candelabra bulbs (3)
j. Part bag contents
1) Mounting hardware :
wood screws (2), flat washers (2),
star washers (2), wire nuts (3),
screws (2)
2) Blade attachment hardware:
screws (17),fiber washers (17)
3) Blade brackets hardware:
extra screws (2)
4) Safety cable hardware:
wood screw, lock washer, flat washer
5) Close mount hardware:
screw with lock washers (3)
6) Pull chain and fobs (2)
7) Balance Kit
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
2. TOOLS AND MATERIALS REQUIRED
a
b
c
d
e
f
g
h
i
j
DorsetTM
3
4. MOUNTING OPTIONS
If there isn't an existing UL (cUL for Canadian
Installation) listed mounting box, then read the
following instructions. Disconnect the power
by removing fuses or turning off circuit
breakers
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1 and 2 are examples of different
ways to mount the outlet box.
NOTE: Depending on the location you have
selected for installation, you may need to
purchase and install a "Joist Hanger" for the
support of the outlet box. Make sure the joist
hanger you purchase has been designed for
use with ceiling fans. (Fig. 3)
Outlet box
Outlet box
Fig. 1
Fig. 3
Outlet box
Fig. 2
4
Fig. 5
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Attach the mounting plate to the outlet
box with the screws and washers provided
with the outlet box. Make sure the mounting
plate is tight and secured. (Fig. 4)
Step 2. Hang the fan motor assembly on the
hook attached to the mounting plate. This will
allow you to use both hands while make the
electrical connections. (Fig. 5)
5. HANGING THE FAN
CUL Listed
electrial
box
Mounting plate
Motor
Fig. 6
6. INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
A safety support cable is provided to help
prevent the ceiling fan from falling, please
install it as follows.
Step 1. Attach the provided wood screw and
washer to the ceiling joist next to the
mounting bracket but do not tighten. (Fig. 6)
Step 2. Adjust the length of the safety cable to
reach the screw and washer by pulling the
extra cable through the cable clamp until the
overall length is correct. Put the end of the
cable back through the cable clamp, forming
a loop at the end of the cable. Tighten the
cable clamp securely.
Now, put the loop in the end of the safety
cable over the wood screw and under the
washer. Tighten the wood screw securely.
Attach safety cable
to ceiling joist with
screw and washer
DorsetTM
Fig. 4
Outlet box
5
Fig. 7
Fig. 8
Fig. 9
7. MAKE THE ELECTRIC CONNECTIONS
Remember to disconnect the power.
Follow the steps below to connect the fan to
your household wiring. Use the wire
connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or
connections.
Step 1 Connect the fan supply (black) wire
and light supply (blue) wire to the black
household supply wire as shown in Figure 7.
Step 2. Connect the neutral fan (white) wire to
the white neutral household wire.
Step 3 Connect the fan ground wire (green) to
the household ground wire.
Step 4 After connecting the wires, spread
them apart so that the green and white wires
are on one side of the outlet box and the
black and the blue wires are on the other side.
Step 5 Turn the connecting nuts upward and
push the wiring into the outlet box.
Figures 8 and 9 illustrate the wiring
connections for optional wall control (The wire
color out of wall control may vary, see wall
control's installation manual for correct wire
connections.)
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR OTHER PERSONAL
INJURY. MOUNT FAN ONLY ON AN OUTLET
BOX OR SUPPORTING SYSTEM MARKED
ACCEPTABLE FOR FAN SUPPORT.
Wiring
box
Ground to
mounting
bracket
or downrod
Power lines 120v
WH
BLUE
BLK BLK
WH
FAN
LIGHT
BLK
BLUE WH
WH
Light
switch
Green ground
WH
BLUE
BLK BLK
WH
GRN
Wiring
box
Ground to
mounting
bracket
or downrod
BLUE
BLK WH
WH
FAN
LIGHT
Power lines 120v
Green ground
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
POWER LINES 120V
GREEN
GROUND
WIRING
BOX
WH
BLUE
BLK BLK
WH
FAN
LIGHT
WH
WH
BLUE
BLK
LIGHT FAN
6
Fig. 10
Fig. 11
8. FINISHING THE INSTALLATION
Step 1. Move fan into position over the four
mounting studs and secure with the provided
washers and nuts. (Fig. 10)
Step 2. Raise the motor housing up against
the mounting plate, the four supports inside
the housing should be placed against the four
studs on mounting plate, twist the housing
clockwise until snug. (Fig. 11)
Washers
Studs
Motor
housing
Nuts
Screws
DorsetTM
7
Fig. 12
Fig. 13
9. ATTACHING THE FAN BLADES
Step 1. Attach a blade to a blade bracket
using the screws and fiber washers provided.
(Fig. 12)
Make sure the blade is straight when set on
the blade bracket. Tighten each mounting
screw and then repeat this procedure for each
blade.
Step 2. Attach each blade assembly to the
motor using the "Pre-Installed" mounting
screws in the blade bracket. (Fig 12)
Screws Blade
Blades bracket
Screws
Fiber
washers
10. INSTALLING THE MOUNTING PLATE
1. Remove 1 of the 3 screws from the
mounting ring and loosen the other 2 screws.
(Do not remove)
2. Place the key holes on the mounting plate
over the 2 screws previously loosened from
the mounting ring, turn mounting plate until it
locks in place at the narrow section of the key
holes. Secure by tightening the 2 screws
previously loosened and the one previously
removed. (Fig. 13)
Mounting
plate
Mounting ring
Screws
8
11. INSTALLING THE LIGHT KIT
Fig. 14
Fig. 15
NOTE: Before starting installation, disconnect
the power by turning off the circuit breaker or
removing the fuse at fuse box. Turning power
off using the fan switch is not sufficient to
prevent electric shock.
Step 1. While holding the Light Kit under your
ceiling fan, push the square wire connectors
together. One from the fan and one from the
switch housing.
NOTE: These connectors are color coded and
will ONLY engage when the colored strips are
matched (aligned).
Step 2. Carefully push all the wires into the
light kit then attach the light kit to the
mounting plate with the screws provided. Be
sure each screw is securely tightened.
12. INSTALLING THE LIGHT BULBS &
GLASS SHADE
1. Install each of the 40 watt candelabra
lamps (included). One in each socket.
2. Remove the decorative nut, glass cap and
metal nut from the light kit. Place glass shade
over the light kit stem, secure with the metal
nut (rubber side on the top), glass cap and
decorative nut. Do not overtighten. (Fig. 15)
3. Insert each control pull chain through the
eyelets in the shade and cap. Thread the
decorative nut on the end of the stem.
4. Restore power and your light kit is ready for
operation.
Note: Make sure to leave enough space
between the fan pull chain and the bulbs so
the chain doesn't rub against any of the bulbs.
DorsetTM
Light kit
Mounting plate
Screws
Wire connector
Light kit
Bulbs
Glass shade
Glass cap
Decorative nut
Metal nut
9
Fig. 16
Fig. 17
13. OPERATING INSTRUCTIONS
Turn on the power and check the operation of
your fan. The pull chain controls the fan speed
as follows:
1. 3-speed pull chain- it controls the fan
speed as follows: 1 pull- High, 2 pulls-
Medium,
3 pulls- Low, and 4 pulls- Off.
Speed settings for warm or cool weather
depend on factors such as the room size,
ceiling height, number of fans, and so on.
2. The Light Kit pull chain turns the light kit
On or Off.
3. The last pull chain reverses the direction of
the fan blades. Counter clockwise for
downward air movement (Summer) and
Clockwise for upward air movement (Winter).
Warm weather - (Counter Clockwise) A
downward airflow creates a cooling effect
as shown in Fig. 16. This allows you to set
your air conditioner on a warmer setting
without affecting your comfort.
Cool weather - (Clockwise) An upward airflow
moves warm air off the ceiling area as shown
in Fig.17. This allows you to set your heating
unit on a cooler setting without affecting your
comfort.
Tabla de contenidos
Otros manuales de Admirador de Kichler Lighting
Kichler Lighting
Kichler Lighting Maeve LED 52 Manual de usuario
Kichler Lighting
Kichler Lighting IMARI 300365SBK Manual de usuario
Kichler Lighting
Kichler Lighting VASSAR Manual de usuario
Kichler Lighting
Kichler Lighting Grace 300316 Manual de usuario
Kichler Lighting
Kichler Lighting Todo 330025 Manual de usuario
Kichler Lighting
Kichler Lighting Spyn Manual de usuario
Kichler Lighting
Kichler Lighting Logan Manual de usuario
Kichler Lighting
Kichler Lighting Richland II Manual de usuario
Kichler Lighting
Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Manual de usuario
Kichler Lighting
Kichler Lighting Seaside 310181WZC Manual de usuario
Kichler Lighting
Kichler Lighting Industrial Fan Manual de usuario
Kichler Lighting
Kichler Lighting Kevlar 310150WCP Manual de usuario
Kichler Lighting
Kichler Lighting Imari 65 Manual de usuario
Kichler Lighting
Kichler Lighting ETL Manual de usuario
Kichler Lighting
Kichler Lighting Hatteras Bay Patio Manual de usuario
Kichler Lighting
Kichler Lighting Sunburst 300170 Manual de usuario
Kichler Lighting
Kichler Lighting BISC 300710MWH Manual de usuario
Kichler Lighting
Kichler Lighting Kimberley Manual de usuario
Kichler Lighting
Kichler Lighting BASICS PRO SELECT 330017MWH Manual de usuario
Kichler Lighting
Kichler Lighting Lija 330140NI Manual de usuario
