KERN ODC-89 Series Manual de usuario

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Microscopio de KERN

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario

Leica

Leica FL560 Manual de usuario

ODC-89-BA-e-1610

KERN & Sohn GmbH

Ziegelei 1

D-72336 Balingen

E-Mail: info@kern-sohn.com

Tel: +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.kern-sohn.com

User instructions

USB m

icroscope

KERN

ODC-89

ODC 894, ODC 895

Version 1.0

01/2016

2

ODC-89-BA-e-1610

KERN ODC-89

Version 1.0 01/2016

User instructions

USB microscope

Before use

You should ensure that the device is not exposed to direct sunlight, temperatures which

are too high or too low, vibrations, dust or a high level of humidity.

The ideal temperature range is between 0 and 40°C and a relative humidity of 85%

should not be exceeded.

Always make sure that you use an approved power cable. Thus possible damages by

reason of the development of overheating (fire hazard) or an electric shock can be

prevented.

Do not open the housing and touch the internal component. There is the risk of damaging

them and affecting the functionality of the camera.

In order to carry out cleanings always disconnect the power cable from the mains supply.

Always keep the sensor clear from dust and do not touch it. Therefore do not remove its

protective housing. Otherwise there is the risk of affecting the microscopic image. In case

of non-use always attach the protective covers.

Technical data

Model

KERN

Resolution

Interface

Sensor

Frame rate

Colour /

Monochrome

Supported operating

systems

ODC 894

2 MP

USB 2.0

1/3,2“CMOS

15 - 30 fps

Colour

Win, XP, Vista, 7, 8, 10

ODC 895

2 MP

USB 2.0

1/3,2“ CMOS

15 - 30 fps

Colour

Win, XP, Vista, 7, 8, 10

Model

KERN

Magnification

levels

Focusing stand

Illumination

ODC 894

10x, 200x

Coaxial

8x LED

ODC 895

10x, 200x

Focus wheel

8x LED

GB

ODC-89-BA-e-1610

3

Scope of delivery

- USB microscope (USB cable incl.)

- Microscope stand

- Software CD

Mounting + functionalities

1. Remove the cover at the bottom of the microscope.

2. Mount the microscope stand and put it onto an even table

surface. Afterwards attach the microscope on the ring holder of

the stand.

3. Establish USB connection to a PC via USB cable.

4. Installing the software with help of the CD.

Detailed instructions can be found in the supplied "readme"-file.

5. Both the supplied "Help"-files and the software-internal "User

Guide" include all information and instructions about the

operation of the software or of digital microscopy.

6. As soon as the software has been started and the image

transmission launched, adjust the illumination level by using the

control wheel, located on the cable.

7. The adjustment of the magnification level is done by using of the

control wheel, located on the side of the microscope.

8. The height adjustment of the microscope stand is done by using

the focus wheels. For the KERN ODC 894 it is aligned coaxial

and for the KERN ODC 895 double-sided on the stand pillar.

9. The USB microscope can also be used without microscope

stand. It can be easily directed towards the specimen by hand.

10. For capturing a snapshot the knob, located on the side of the

microscope (above the control wheel for the magnification

adjustment), needs to be pressed.