Kenwood TS-2000 Manual

Adjustment mode operation procedure

There is only one way to adjust the settings.

The only way to do so is with the adjustment Mode menu.

This menu has workt from 00 to 126.

TAKE CARE WITH IT USE AT YOUR OWN RISK!!!!!!!!!!!!!!!!!!!

Adjustment mode:

The TS 2000 can be adjusted manually (by turning a coil, trimmer, etc

or by setting the service adjustment mode (simply referred to as the

adjustment mode below)

adjustments items are shown in menu No: 00 to 126.

and all data are saved in the EEPROM (x53-391: IC7) :-)

To enter adjustment mode, the user firmware in the main unit must be

rewritten with adjustment firmware (The user firmware is the factory

setting)

MAKE SURE YOU HAVE THE USER FIRMWARE AS A BACK UP!!!!!!!!!!!!!!!!!!!

(we do not think we have to explane to you how to get the firmware

and how to upload it in the set in case of a crash if we have to do

that please do not start this procedure at all.!!!!!!!!!!!!!!!)

Oke let's go to step 2.

main way (frame) to do the job, only the main things are mentioned and

the explanation will be followed later on.

1) Checksum confirmation.

Switch the transceiver on while pressing and hold N.R.

and MIC/CAR keys.

2)Preparation of uploading data.

1. Access menu No. 56 and select 9600 bps, then switch the

transceiver OFF.

2. Back up the user data in the transceiver (menu configuration and

Memory channel daqta)

Run the programming software (W05-0855-00), then select "Menu/MRch

read from RADIO"

Name the file and save it somewhere where you can find it easily.

3)Uploading the the adjustment firmware

1.Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).

2.Upload the adjustment firmware, using " adjust firmware write menu.

3.Turn the switch (S1) off in TX-RX1 unit (x57-605 A).

4)Turn the tranceiver ON while pressing A=B key to perform the full

reset.

4. Adjustments

5. Uploading the user firmware.

1.TURN THE SWITCH (S1) on IN TX-RX1 UNIT (X57-605 a).

2.Upload the user firmware, using"user firmware write" menu.

3.Turn the switch (S1) OFF in Tx-Rx1 unit.

4.Turn the transceiver ON while pressing A=B key to perform the full

reset.

6. Checsum confirmation

Switch the transceiver on while pressing and hold N.R. and mic/car

keys.

If the user firmware has not changed, the checsum is the same as the

value in step 1.

If the user firmware has been updated the checsum should match the

new checksum.

7.Uploading the user firmware.

1. Turn the transceiver on while pressing a=b key to perform the full

reset.

2. Run the programming software (w05-0855-00), then select

menu/MRch Write to the radio.

PROCEDURE FOR WRITING ADJUSTMENT FIRMWARE (FOR BOTH USER AND

ADJUSTMENT FIRMWARE)

1. REMOVE THE LOWER CASE AND SET THE SLIDE SWITCH (S1) of the TX-RX 1

unit (x57-605A) to on (move the switch toward the front)

2. Connect the RS 232 C port of the personal computer with the COM

port of the main unit with a D-SUB (9-pin) straight cable (female-

female) this is the same cable as you use for all other software

comminication with the set.

3.Connect the external power suply put it ON The main unit does not

turn on any indicators, but it is ready to rewrite firmware.

Do not operate the power switch on the main unit!!!!!

4. write firmware using the writing software. there is a help file

with the software!!

5.After writing the the firmware turn the external power suply OFF

and remove the rs 232 cable.

6. Set the slide switch (you know now where it is??? :-)

(s1) to off (move the4 switch toward the rear)

7.Turn the external power suply ON

8.Turn the main unit ON and confirm that the indicator lights.

Then perform all reset (hold down A=B key and press the power key and

confirm that the initial state is displayed.

9. After adjustment rewrite adjustment software back to user firmware

using the writing software.

10.After rewriting user software, check the checsum (hold down the

N.R. and MIC/CAR keys and press the POWER key. then Menu No 125.

Then, perform all reset.

Notes

When adjustment software is loaded and the main unit is turned ON, A

beep sounds to indicate the adjustment mode. THIS DOES NOT INDICATE A

FAILURE.

Whenany key (exept PF key is pressed after a frequency is displayed,

the beep stops.

Adjustment mode operation procedure.

1. Start the adjustment mode.

Hold down th NR an mic/car keys and press the Power key.

The adjustment mode is set and a menu number is displayed below the

M.CH on the main band side (left) of the display.

2. Select adjustment mode menu number.

Turn the MULTI CH knob to change the menu No.

3. Change adjustment mode setting data.

Setting data can be changed with + or - key.

4.Write adjustment mode data.

Press + or - key on the main unit op UP or DOWN key on the microphone

on menu 124. witch will wrhite the eeprom.

5.Cancel adjustment Mode.

Press the CRL key to return to the normal VFO mode.

When the power is turned OFF in the middle in the adjustent mode, it

is canceled.

Otros manuales para TS-2000

Tabla de contenidos

Otros manuales de Transceptor de Kenwood

Kenwood

Kenwood TK-3230DX Manual de usuario

Kenwood

Kenwood TK-5210 Manual de usuario

Kenwood

Kenwood TR-7730 Manual de usuario

Kenwood

Kenwood NEXEDGE NX-220 Manual de usuario

Kenwood

Kenwood NEXEDGE NX-800H Manual de usuario

Kenwood

Kenwood TM-201A Manual de usuario

Kenwood

Kenwood TS-680S Manual de usuario

Kenwood

Kenwood TK-830/(B)/(D) Manual de usuario

Kenwood

Kenwood TS-440S Manual de usuario

Kenwood

Kenwood TK-8302 Manual de usuario

Kenwood

Kenwood TK-5720 Manual de usuario

Kenwood

Kenwood TS-950SDX Manual de usuario

Kenwood

Kenwood TM?D710 Guía de instalación

Kenwood

Kenwood TR-2600 A Manual de usuario

Kenwood

Kenwood TH-25A Series Manual de usuario

Kenwood

Kenwood TH-21A Manual de usuario

Kenwood

Kenwood TK-5210 Manual de usuario

Kenwood

Kenwood TS-940S Manual de usuario

Kenwood

Kenwood TS-700A Manual de usuario

Kenwood

Kenwood NX-5000 series Manual de usuario

Kenwood

Kenwood TH-22AT Manual de usuario

Kenwood

Kenwood UBZ-LF14 Manual de usuario

Kenwood

Kenwood TK-8102 Manual de usuario

Kenwood

Kenwood TM-221A Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario

Uniden

Uniden UH820 Series Manual de usuario

Standard Horizon

Standard Horizon HX320E Manual de usuario

Em-Trak

Em-Trak A100 Manual de usuario

HPE

HPE Aruba QSFP28 Manual de usuario