Kenwood Chef KM330 series Manual de usuario
KM330 series Chef / KM630 series Major - (Pinto)
The following procedures are aimed to help with dismantling and service repairs.
Always disconnect the appliance from mains supply prior to removal of the covers and suitably protect the finish on the
casings.
Click on the pictures to open a larger version in a seperate window.
To access the gearbox:
Remove the high speed outlet cover.
Pull back the slow speed lever to
unlock and remove the slow speed
outlet cover.
Please note the correct position of the
spigot prior to removal.
* The positioning of the spigot
determines the position of the
attachments, when fitted.
Remove the top cover.
Page 1 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Remove the plastic washer and drive
belt.
Dismantling the gearbox involves
removal of the large pulley. Either of
the following methods will assist:
Use a stall plug:
Fit the stall plug in the slow speed
outlet. If necessary, use a screwdriver
to rotate it into position. Undo the
gearbox pulley by hand anti-
clockwise.
Page 2 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Use a mincer.
Attach the mincer and position a
screwdriver between the cutter blades
and close to the scroll to stop it
rotating. Please note, it is advisable to
use the coarse screen as this allows
room for a larger diameter
screwdriver. Undo the gearbox pulley
by hand anti-clockwise.
The pulley is a tight fit on the pinion
shaft. Use two screwdrivers to prise it
off.
Re-assemble using the stall plug /
mincer, turning pulley clockwise to
tighten.
Page 3 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Removing / replacing the planet hub assembly:
The hub nut is secured by an
engineering adhesive, and may prove
difficult to remove. Use an 8mm
socket, and position a tool between
the hub spout and the hub nut, as
shown, taking care not to damage the
finish. Turn anti clockwise to remove.
* If the hub proves difficult to remove,
stand the appliance upright and tap
the end of the screw (vertical drive
shaft) with a mallet, whilst at the same
time pulling down on the hub spout.
Apply grease sparingly to the planet
gear, this will then transfer to the ring
gear.
Page 4 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Apply threadlock 60026 to the hub nut
prior to re-assembly.
Regreasing the gearbox:
With the machine upside down,
remove the slow speed lever knob as
shown, and undo the two gearbox
cover screws and remove the cover.
Page 5 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Remove the red plug, then re-grease
with the appliance running on the
lowest speed setting.
* The special food-grade grease is a
stock item.
To remove the motor & control module:
Remove all top covers as detailed above.
Remove the three motor retaining
screws and cams.
* Please note, the motor retaining
screws should never be
overtightened, as this can cause them
to eventually work loose.
Page 6 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Loosely refit the top cover and the
liquidiser outlet cover to serve as a
stand. Use a mat to protect the
casing, and turn the appliance upside
down.
Loosen the two cord grip screws and
pull the mains lead through as shown.
Page 7 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Operate the head lift lever, restrain the
pedestal at the same time, and allow
the machine to open slowly. Remove
the two screws securing the quadrant
bracket.
Remove the bracket and screws,
operate the head lift lever, then slide
the quadrant into the pedestal.
Page 8 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
The motor assembly, control module
and body cover can now be lifted out
of the body.
The date code can be found on the flat
face of the motor housing.
Please note, only the four upper
characters make up the date code. In
this example the date code reads
6M42, which translates as, 2006-
October-week 42. Click here for more
details on Product Date Codes.
Page 9 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Control module dismantled.
To remove the pedestal:
With the machine upside down, and
the quadrant screws removed, move
the body cover out of position to
expose the hinge pin, then remove the
circlip.
Page 10 of 15Spares - KM330 / KM630 series - Disassembly & re-assembly instructions
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/
g
uide-KM330.htm
Otros manuales para Chef KM330 series
3
Este manual sirve para los siguientes modelos
1
Otros manuales de Electrodoméstico de cocina de Kenwood
Kenwood
Kenwood CK 231 E Manual de usuario
Kenwood
Kenwood KXT0010G Manual de usuario
Kenwood
Kenwood TRIBLADE XL+ HBM60 Manual de usuario
Kenwood
Kenwood HM620 series Manual de usuario
Kenwood
Kenwood CP658 Guía de instalación
Kenwood
Kenwood CP658 Guía de instalación
Kenwood
Kenwood KHC29 Manual de usuario
Kenwood
Kenwood AT950A Manual de usuario
Kenwood
Kenwood KAX720PL Manual de usuario
Kenwood
Kenwood KPL90 Manual de usuario
Kenwood
Kenwood CL420 series Manual de usuario
Kenwood
Kenwood Titanium Chef Baker XL KVC85 Manual de usuario
Kenwood
Kenwood CHEF Manual de usuario
Kenwood
Kenwood KAH65.000PL Manual de usuario
Kenwood
Kenwood FP110 series Manual de usuario
Kenwood
Kenwood AT644 Manual de usuario
Kenwood
Kenwood JE770 series Manual de usuario
Kenwood
Kenwood A938 Manual de usuario
Kenwood
Kenwood CO606 Manual de usuario
Kenwood
Kenwood BLP41.A0CT Manual de usuario
