Kenwood Major KM001 series Instrucciones de operación
Please pick one of the following:
DISMANTLING AND RE-ASSEMBLING OF SOVEREIGN - KM001/002/003 AND
KM005/006/007
TOP COVER
MOTOR
LATCH ASSEMBLY
PEDESTAL GEARBOX SPEED CONTROL KNOB
TOP COVER
1. REMOVE ALL COVERS
2. REMOVE 4 SCREWS AND SPIGOTS
(NO.2 POZIDRIVE)
3. REMOVE SPIGOT PLATE
(A SMALL FLAT BLADED SCREWDRIVER
INSERTED BETWEEN THE PLATE AND THE
CASTING CAN BE USED TO EASE OFF THE
PLATE AROUND THE HIGH SPEED SPIGOT)
Page 1 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
4. REMOVE 3 SCREWS
(NO.2 POZIDRIVE)
5. RAISE HEAD
6. REMOVE 2 SCREWS (TX15)
7. LOWER HEAD
8. LIFT OFF TOP COVER FROM HIGH
SPEED OUTLET END OF CASTING
Page 2 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Click here to return to the top of the page.
9. RE-ASSEMBLY IS THE REVERSE OF
STEPS 1-8 EXCEPT TAKE CARE TO AVOID
DISTURBING ANTI-VIBRATION CAP ON
THE GEARBOX.
PEDESTAL
1. REMOVE ALL COVERS
Page 3 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
2. INVERT THE APPLIANCE
3. REMOVE 2 STUFFER BOX
SCREWS
(TX15 OR TX20)
4. UNCLIP AND REMOVE LID
5. REMOVE 2 FIXING SCREWS (TX20)
6. REMOVE BOX
(HANDY AS SCREW TRAY AT THIS POINT)
7. REMOVE CABLE CLAMP SCREW (TX20)
8. REMOVE CABLE CLAMP
Page 4 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
9. CAREFULLY OPERATE THE HEAD
RELEASE WHILE RESTRAINING THE
PEDESTAL. ALLOW TO FULLY OPEN
SLOWLY.
WARNING: THE PEDESTAL WILL SPRING
UP VIOLENTLY UNLESS IT IS RESTRAINED
10. REMOVE 4 SCREWS (TX20)
(NOTE - ONE REAR SCREW MAY BE CHANGED
TO TX15 ON LATER PRODUCTION)
TAKE CARE TO AVOID SCRATCHING BODY
WITH THE HEAD LIFT MECHANISM
11. REMOVE LOCATION PIN (8MM HEX
NUT)
12. LIFT QUADRANT COVER AND
DISCONNECT 3 CONNECTORS
(SENSORS, MOTOR SUPPLY, POWER SUPPLY)
13. REMOVE SPEED CONTROL MODULE
14. REMOVE QUADRANT COVER
Page 5 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Click here to return to the top of the page.
15. HINGE PIN PUSHES OUT IF REQUIRED
(RETAINED BY VENT PANEL IN BODY)
16. RE-ASSEMBLY IS THE REVERSE OF
STEPS 1-14 EXCEPT TAKE CARE THAT THE
POWER SUPPLY CABLE DOES NOT RUB
ON THE FAN
MOTOR
1. REMOVE TOP COVER
2. REMOVE TOP WASHER
3. REMOVE 3 MOTOR SCREWS (NO.2
POZIDRIVE)
Page 6 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
4. REMOVE BELT
5. PLACING THE TOP COVER IN POSITION
AT THIS STAGE STABILIZES THE
APPLIANCE WHEN INVERTED
6. STRIP DOWN PEDESTAL AS FAR AS
STEP 14. REMOVE QUADRANT COVER
7. REMOVE SINGLE VENT PANEL SCREW
(TX20)
8. REMOVE VENT PANEL
9. REMOVE MOTOR
10. REPLACE MOTOR IN REVERSE ORDER
EXCEPT FIT MOTOR SCREWS (STEP 3)
FIRST
11. FAN AND PULLEY - : THESE PARTS
CAN ONLY BE REPLACED WITH THE AID OF
A PRESS, AS THE MOTOR WILL BE
DAMAGED BY SHOCK LOADS ALONG IT'S
AXIS. THIS MAY SHOW UP AS BELT WEAR
ON THE BODY
12. BRUSHES
13. REMOVE SLEEVE HELD TO TWO CLIPS
Page 7 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Click here to return to the top of the page.
14. UNLATCH SPRING
15. REMOVE TAG
16. REMOVE BRUSH
17. REASSEMBLE IN REVERSE ORDER
GEARBOX
Dismantling the gearbox involves
removal of the large pulley.
Either of the following methods
will assist:
Use a stall plug:
Fit the stall plug in the slow
speed outlet. If necessary, use a
screwdriver to rotate it into
position. Undo the gearbox
pulley by hand anti-clockwise.
Page 8 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Click here to return to the top of the page.
Use a mincer.
Attach the mincer and position a
screwdriver between the cutter
blades and close to the scroll to
stop it rotating. Please note, it is
advisable to use the coarse
screen as this allows room for a
larger diameter screwdriver.
Undo the gearbox pulley by hand
anti-clockwise.
LATCH ASSEMBLY
Page 9 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instructio...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Click here to return to the top of the page.
1. INVERT THE APPLIANCE
2. CAREFULLY OPERATE THE HEAD
RELEASE WHILE RESTRAINING THE
PEDESTAL. ALLOW TO FULLY OPEN
SLOWLY
WARNING: THE PEDESTAL WILL SPRING
UP VIOLENTLY UNLESS IT IS RESTRAINED!
3. UNHOOK LATCH SPRINGS
4. REMOVE C-CLIP
5. PULL OUT LATCH BAR
6. RE-ASSEMBLE IN REVERSE ORDER
SPEED CONTROL KNOB
1. REMOVE MODULE (SEE PEDESTAL)
2. REMOVE REAR COVER
NOTE: - POTENTIOMETER IS PRE-SET TO
PROVIDE CORRECT PULSE OPERATION,
RATHER THAN A DIRECT LINK TO SPEED.
ADJUSTMENT REQURIES SPECIAL TRAINING
Page 10 of 11Spares - KM001/002/003/502/005/006/007/506 Disassembly & re-assembly instruc...
30/04/2009http://www.kenwoodservice.co.uk/product-files-kar/soverei
g
n-tech2.htm
Otros manuales para Major KM001 series
4
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Procesador de alimentos de Kenwood
Kenwood
Kenwood MULTIPRO COMPACT Manual de usuario
Kenwood
Kenwood Premier Chef KMC57002 Manual de usuario
Kenwood
Kenwood FDM31 Manual de usuario
Kenwood
Kenwood FPM800 series Manual de usuario
Kenwood
Kenwood FPM90 Manual de usuario
Kenwood
Kenwood PM900 Manual de usuario
Kenwood
Kenwood FPM260 series Manual de usuario
Kenwood
Kenwood Chef KMC510 Manual de usuario
Kenwood
Kenwood FP980 series Manual de usuario
Kenwood
Kenwood FP910 series Manual de usuario
Kenwood
Kenwood FP940 series Manual de usuario
Kenwood
Kenwood FP582 Guía de instalación
Kenwood
Kenwood Cooking Chef Major Manual de usuario
Kenwood
Kenwood CCL45 Manual de usuario
Kenwood
Kenwood CH550 Manual de usuario
Kenwood
Kenwood MultiPro Go Manual de usuario
Kenwood
Kenwood FDM791 Manual de usuario
Kenwood
Kenwood multipro FP710 series Manual de usuario
Kenwood
Kenwood FP108 series Guía de instalación
Kenwood
Kenwood FPM91 Manual de usuario
