Kenwood KCA-SR50 - Complete Sirius Satellite Radio... Manual de usuario

KCA-SR50

SIRIUS INTERFACE BOX FOR CONNECTING KENWOOD HEAD

UNITS TO SIRIUS RECEIVERS

INSTRUCTION MANUAL

BOITIER D'INTERFACE SIRIUS POUR BRANCHEMENT

D'UNITES PRINCIPALES KENWOOD AU RECEPTEURS SIRIUS

MODE D’EMPLOI

CAJA DE INTERFACE SIRIUS PARA CONECTAR UNIDADES

KENWOOD A RECEPTORES SIRIUS

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best

performance from your new SIRIUS interface box.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model KCA-SR50 Serial number

US Residence Only

www.Kenwoodusa.com

Sirius Satellite Radio Inc.

B64-3921-0000.indb1B64-3921-0000.indb1 07.6.289:31:32AM07.6.289:31:32AM

2|English

Contents

Safety precautions/ Notes 3

Notes 4

Operations 5

How to read

SIRIUS ID [ESN] display

Select SIRIUS Satellite Radio Mode

Selecting the Preset Band

Tuning

Channel Preset Memory

Preset Tuning

Channel Scan

Switching Seek Mode

Category and Channel Search

Switching Display

Direct Access Tuning

Accessories/ Installation Procedure 7

Connecting Wires to Terminals 8

Installation 9

Troubleshooting Guide 10

Specifications 11

B64-3921-0000.indb2B64-3921-0000.indb2 07.6.289:31:33AM07.6.289:31:33AM

English |3

2WARNING

To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools) inside

the unit.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting

and wiring work to professionals.

2CAUTION

To prevent damage to the machine, take

the following precautions:

• Do not open the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of

water splashing.

• Use only the screws provided or specified for

installation. If you use wrong screws, you could

damage the unit.

• When drilling a hole in the car to fix the brackets,

make sure not to damage the fuel tank, brake tube,

wiring harnesses, etc. on the other side.

NOTE

• If you experience problems during installation,

consult your Kenwood dealer.

• If the unit does not seem to be working right, try

pressing the reset button on the control unit first.

If that does not solve the problem, consult your

Kenwood dealer.

• When the reset button is pressed, the SIRIUS satellite

radio becomes ready to receive after approximately

15 seconds.

Safety precautions/ Notes

B64-3921-0000.indb3B64-3921-0000.indb3 07.6.289:31:33AM07.6.289:31:33AM

4|English

Notes

Connectable Models

2007 models

*KDC-X991, *KDC-X891, *KDC-X791, *KDC-MP735U,

*KDC-MP635

KDC-X591, KDC-X491, KDC-MP535U, KDC-MP435U,

KDC-MP3035, KDC-MP335, KDC-MP2035,

KDC-MP235, DPX502, DPX302

*KVT-819DVD, *KVT-719DVD, *DDX8019, *DDX7019,

*DNX7100, *DNX710EX, *KOS-V1000, *KOS-V500

2006 models

*KDC-X990, *KDC-X890, *KDC-X790, *KDC-MP832U,

*KDC-MP732

KDC-X590, KDC-MP632U, KDC-MP532U,

KDC-MP5032, KDC-MP4032, KDC-MP2032,

KDC-MP332, KDC-MP232, KDC-232MR,

DPX701, DPX501, DPX301

*KDV-412, *KVT-617DVD, *DDX6019, *KOS-A200

2005 models

*XXV-01D, *KDC-X889, *KDC-X789, *KDC-MP928,

*KDC-MP828, *KDC-MP7028, *KDC-MP728,

*KDC-MP628

KDC-X589, KDC-MP5028, KDC-MP528, KDC-MP4028,

KDC-MP428, KDC-MP2028, KDC-MP228, KDC-3028,

KDC-328, KDC-228, Ez500

*XXV-05, *KVT-817DVD, *KVT-717DVD, *KVT-M707,

*DDX8017, *DDX7017

⁄

• For the models marked with *, the operation method is

different from that discussed in this manual. Refer to the

Instruction Manual that comes with each control unit.

• For the connectable models released since 2008, contact

the dealer.

NOTE

When initially activating your subscription, if you

have changed your subscription, or if SIRIUS itself

has updated streaming broadcast service, automatic

reselection of reception operates by following the

current channel setting.

At this time, audio reception may be momentarily

interrupted. However, this interruption is not caused

by radio interference or reception interference.

FCC WARNING

This equipment may generate or use radio

frequency energy. Changes or modifications to this

equipment may cause harmful interference unless

the modifications are expressly approved in the

instruction manual. The user could lose the authority

to operate this equipment if an unauthorized change

or modification is made.

NOTE

This Class B digital apparatus complies with

Canadian ICES-003.

B64-3921-0000.indb4B64-3921-0000.indb4 07.6.289:31:34AM07.6.289:31:34AM

English |5

Operations

SIRIUS ID [ESN] display

You must have the SIRIUS ID number [ESN] for

licensing with SIRIUS Corp. Check the SIRIUS ID

[ESN] of this unit as follows.

1Select the SIRIUS Satellite Radio Mode

Press the [SRC] button.

Select the "SIRIUS"/"SAT" display.

2Check the SIRIUS ID [ESN] of this unit

See the <Menu System> page of the instruction

manual of your control unit, and select the ESN

menu item.

The SIRIUS ID [ESN] will be displayed.

⁄

• Serial & SIRIUS ID [ESN]

It is especially important to retain the unit serial number

and the electronic SIRIUS Identification number for

service activation and potential future service changes.

Select SIRIUS Satellite Radio Mode

Listening to the SIRIUS satellite radio.

Press the [SRC] button.

Select the "SIRIUS"/"SAT" display.

⁄

• You need to subscribe to SIRIUS to receive the service

by SIRIUS Satellite Radio. Consult SIRIUS if "CALL 888-539

SIRIUS TO SUBSCRIBE"/"CALL 888 539-SIRI" appears.

• It may take a little time to start receiving after you

selected the SIRIUS source.

• If the signal receiving fails, "Acquiring Signal"/

"ACQUIRING SIGNAL" appears.

Selecting the Preset Band

ÅPush the Control knob toward up.

Each time you push the knob toward up, it

switches between the SR1, SR2, SR3 and SR4.

Tuning

Selecting the channel.

ÅPush the Control knob towards right or left.

ıPress the [4] or [¢] button.

Channel Preset Memory

Putting the channel in the memory.

1Select the preset band

ÅPush the Control knob toward up.

ıPress the [FM] button.

2Select the channel to put in the memory

ÅPush the Control knob towards right or left.

ıPress the [4] or [¢] button.

3Put the channel in the memory

Press the desired [1] — [6] button for at least 2

seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the memory

on each [1] — [6] button.

⁄

• Only the channel number is stored. Category information

is not stored.

• This function can be used only when the "Channel"/

"CHANNEL" has been selected in <Switching Seek

Mode> (page 6).

Preset Tuning

Calling up the channels in the memory.

1Select the preset band

ÅPush the Control knob toward up.

ıPress the [FM] button.

2Call up the channel

Press the desired [1] — [6] button.

How to read

The operation method differs depending on the

model of the control unit.

For the model with a Control knob, perform the

operation steps marked with Å. For other models,

perform the operation steps marked with ı.

ıPress the [FM] button.

Each time the button is pressed, the preset band

switches between the SR1, SR2, SR3 and SR4.

B64-3921-0000.indb5B64-3921-0000.indb5 07.6.289:31:34AM07.6.289:31:34AM

6|English

Operations

Switching Display

When you are listening to the Sirius satellite radio,

you can switch over the display information as

follows.

For operations, see the <Switching Display>

page of the instruction manual of your control

unit.

⁄

• What is displayed may partly depend on control units to

be connected.

Information

Channel Name

Song Title

Artist Name

Composer name

Category Name

Band & Channel Number

⁄

• If the text, including Channel name, etc. is selected

when the channel which does not have text, including

Channel name, etc. is played, band & channel number is

displayed.

Channel Scan

Every receivable channel is checked for 10 seconds.

1Start Channel Scan

Press the [AUTO] button for at least 2 seconds.

The channel scan will start.

2Release it when the channel you want to listen

to is received

Press the [AUTO] button for at least 2 seconds.

Switching Seek Mode

Sets the seeking mode.

Press the [AUTO] button.

Each time the button is pressed, the Seek mode

switches as shown below.

Display Operation

"Channel"/"CHANNEL" Normal manual seeking control.

"Preset"/"PRESET" Search in order of the channels in the

Preset memory.

⁄

• This function cannot be used in the category and

channel search mode.

Category and Channel Search

Select the category and channel you wish to listen

to.

1Enter category and channel search mode

Press the [38] button.

2Select the category

ÅPush the Control knob towards up or down.

ıPress the [FM] or [AM] button.

3Select the channel

ÅPush the Control knob towards right or left.

ıPress the [4] or [¢] button.

Canceling category and channel search mode

Press the [38] button.

⁄

• You cannot operate this unit until all the Category

information is acquired.

Function of remote control

Direct Access Tuning

Entering the channel and tuning.

1Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote

control.

2Enter the channel

Press the number buttons.

3Do Channel Search

Press the [4] or [¢] button.

Canceling Direct Access Tuning

Press the [DIRECT] button on the remote

control.

⁄

• If you make no button operation for 10 seconds, the

Direct Access Tuning mode is automatically canceled.

• If you cannot receive any signal in the input channel due

to a bad condition on radio wave or another problem,

"Acquiring Signal"/ "ACQUIRING SIGNAL" appears.

B64-3921-0000.indb6B64-3921-0000.indb6 07.6.289:31:34AM07.6.289:31:34AM

English |7

Accessories

..........1

..........2

..........4

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the -battery.

2. Connect the SIRIUS interface box and the control

unit using the provided SIRIUS connection wire.

3. Make the proper input and output wire

connections for each unit.

4. Install the unit in your car.

5. Reconnect the -battery.

6. Press the reset button.

• Do not connect the SIRIUS connection wire while the

control unit is turned ON.

• Be sure to press the reset button on the control unit after

installation.

• If your car is not prepared for this special connection-

system, consult your Kenwood dealer.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• Do not let unconnected wires or terminals touch metal on

the car or anything else conducting electricity. To prevent

short circuits, also do not remove the caps on the ends of

the unconnected wires or the terminals.

• Insulate unconnected wires with vinyl tape or other similar

material.

• Take care so that the antenna wire and other connection

wires are not caught by mobile parts. Otherwise wire

disconnection or other trouble may result.

• Do not apply too much force on the antenna wire, other

connection wires and connectors by bending a wire, etc.

Otherwise wire disconnection or other trouble may result.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

Accessories/ Installation Procedure

B64-3921-0000.indb7B64-3921-0000.indb7 07.6.289:31:35AM07.6.289:31:35AM

8|English

Connecting Wires to Terminals

If you want to connect KCA-S220A

Control unit

KCA-SR50

SIRIUS Universal

Tuner or Portable

Tuner

(Front side)

(Rear side)

SIRIUS connection wire

(Accessory1)

To Kenwood disc changer/ SIRIUS

control input

CHANGER 2

CHANGER 1

H/U

HEAD UNIT

KCA-S220A

Control unit

Disc changer

KCA-SR50

⁄

• Connect the KCA-SR50 to the terminal labelled TO CHANGER 2.

• Please keep the total extension of the control cable from the control unit to the disc changer to 13 m or less. Control cable

lengths in excess of 13 m will cease to function properly.

• Do not connect any unit other than the

SIRIUS tuner. A failure could result.

⁄

• When using with the KCA-BT100 or

KTC-HR100TR, connect to it.

B64-3921-0000.indb8B64-3921-0000.indb8 07.6.289:31:35AM07.6.289:31:35AM

English |9

Installation

• Install the unit in a well-ventilated location and do not place

objects on top of it.

• When installing to the car, the unit should be securely

fastened at a location that will not interfere with driving.

• When making a hole in the chassis, check that the gas tank,

break pipe, wire harness, or other part is not located on the

other side, and be careful not to cause scratches.

Installation using the self-tapping

screws

Board etc.

thickness: 15 mm or more

Carpet

Accessory3

(Ø4 × 12 mm)

Installation using the velcro tapes

Accessory2

Carpet

• Please do not install the unit near the dashboard, the rear

tray, or other important components. Doing so could lead

to injury or accident should the unit come off due to a

shock and strike a person or an important component.

Tapping screws should be used for mounting. (Attachment

with velcro strips, although easy, can come off with a

shock.)

B64-3921-0000.indb9B64-3921-0000.indb9 07.6.289:31:37AM07.6.289:31:37AM

If you use this for the first time, it may be

difficult to receive signals in the beginning.

In such a case, leave the SIRIUS source ON

for 3 minutes and turn it OFF and ON.

What might appear to be a malfunction in

your unit may just be the result of slight

misoperation or miswiring. Before calling

service, first check the following table for

possible problems.

? The SIRIUS mode cannot be selected.

✔The SIRIUS connection wire is not connected.

☞Use the SIRIUS connection wire to connect the

control unit and the SIRIUS satellite radio tuner.

✔The changer switching unit "KCA-S220A" is not

connected properly.

☞Connect the KCA-SR50 to the terminal labelled

TO CHANGER 2. See the section on <Connecting

Wires to Terminals>.

? Nothing happens when the buttons are pressed.

✔The computer chip in the unit is not functioning

normally.

☞Press the reset button on the Control unit.

? No broadcast can be received.

✔No subscription is established.

☞Subscribe to SIRIUS.

The following messages are displayed

when certain problems are occurring

in your system. Take the recommended

actions.

ANTENNA ERROR / ANT ERR / ANT ERROR :

Antenna is not connected correctly.

➪Make sure the antenna is connected

correctly and then turn OFF/ON of the

SIRIUS source or Control unit.

TUNER ERROR / TUNE ERR :

Broadcast cannot be received due to an error

in this unit.

➪Turn OFF/ON of the SIRIUS source or

Control unit, or press the reset button of

Control unit.

ESN ERROR / ESN ERR :

ESN (Electronic Serial Number) is not

registered in this unit.

➪Consult your nearest service center.

CHECK SIRIUS / CHK SSR :

The SIRIUS tuner is disconnected or a unit

other than the SIRIUS tuner is connected.

➪Check the connection to the SIRIUS tuner.

10 |English

Troubleshooting Guide

B64-3921-0000.indb10B64-3921-0000.indb10 07.6.289:31:37AM07.6.289:31:37AM

Otros manuales para KCA-SR50 - Complete Sirius Satellite Radio...

Tabla de contenidos

Otros manuales de Adaptador de Kenwood

Kenwood

Kenwood KTI-5 Manual de usuario

Kenwood

Kenwood IL-KNW Manual de usuario

Kenwood

Kenwood KMB-35A Manual de usuario

Kenwood

Kenwood GP-610A Manual de usuario

Kenwood

Kenwood Nexedge KTI-4 Manual de usuario

Kenwood

Kenwood KCA-WL100 Manual de usuario

Kenwood

Kenwood KPA-SD100 Manual de usuario

Kenwood

Kenwood KCA-SR50 - Complete Sirius Satellite Radio... Manual de usuario

Kenwood

Kenwood KBA-700 Manual de usuario

Kenwood

Kenwood KVC-22 Manual de usuario

Kenwood

Kenwood Nexedge KTI-4 Manual de usuario

Kenwood

Kenwood CAW-CANOP1 Manual de usuario

Kenwood

Kenwood a2d-knw Manual de usuario

Kenwood

Kenwood CA-SR20V Manual de usuario

Kenwood

Kenwood IP-KNW Manual de usuario

Kenwood

Kenwood KCA-BT300 Manual de usuario

Kenwood

Kenwood CAW-RN7400 Manual de usuario

Kenwood

Kenwood KCA-ML100 Manual de usuario

Kenwood

Kenwood KAT001ME Manual de usuario

Kenwood

Kenwood KPA-HD100 Manual de usuario

Kenwood

Kenwood KCA-IP500 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario