Kentec Electronics Taktis Vision Manual de usuario
Safety
Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work act 1974 to ensure
as reasonably as is practical that the article will be safe and without risk to health when properly used.
An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating
to its use made available by the supplier.
This product should be installed, commissioned and maintained by trained service personnel in accordance with the
following:
• EE regulations for electrical equipment in buildings
• Codes of practice
• Statutory requirements
• Any instructions specifically advised by The Manufacturer
According to the provisions of the Act you are therefore requested to take such steps as are necessary to ensure
that you make any appropriate information about this product available to anyone concerned with its use.
The mains powered version of this equipment is designed to be operated from 230V 50Hz mains supplies and is of
class 1 construction. As such it must be connected to a protective earthing conductor in the fixed wiring of the in-
stallation and a readily accessible double pole disconnect device shall be incorporated in the fixed wiring.
Failure to ensure that all conductive accessible parts of this equipment are adequately bonded to the pro-
tective earth will render the equipment unsafe.
Disclaimer
In no event shall The Manufacturer be liable for any damages or injury of any nature or kind, no matter how caused,
that arise from the use of the equipment referred to in this manual.
Strict compliance with the safety procedures set out and referred to in this manual, and extreme care in the handling
or use of the equipment, are essential to avoid or minimise the chance of personal injury or damage to the equip-
ment.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are believed
to be correct and accurate as at the date of publication or revision. However, no representation or warranty with re-
spect to such correctness or accuracy is given or implied and The Manufacturer will not, under any circumstances,
be liable to any person or corporation for any loss or damages incurred in connection with the use of this manual.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to
change without notice.
Unauthorised modifications to the fire detection system or its installation are not permitted, as these may give rise
to unacceptable health and safety hazards.
By installing this equipment on a computer network, the owner accepts full and unequivocal responsibility for ensur-
ing that it is protected against all cyber threats and illegal tampering during the lifetime of the equipment.
Any software forming part of this equipment should be used only for the purposes for which The Company supplied
it. The user shall undertake no changes, modifications, conversions, translations into another computer language,
or copies (except for a necessary backup copy).In no event shall The Manufacturer be liable for any equipment mal-
function or damages whatsoever, including (without limitation) incidental, direct, indirect, special, and consequential
damages, damages for loss of business profits, business interruption, loss of business information, or other pecuni-
ary loss, resulting from any violation of the above prohibitions.
www.acornfiresecurity.com
www.acornfiresecurity.com
Contents i
Man-1161EN Rev. 01
Taktis Vision Installation & Operation Manual
Section 1
Introduction 1
Taktis Vision Annunciator Features ..............................................................................................................1
Related Documentation.................................................................................................................................1
Section 2
Overview 2
Fascia Layout................................................................................................................................................2
Internal Features ...........................................................................................................................................3
Section 3
Installation 4
Before You Begin ..........................................................................................................................................4
General Installation Checklist........................................................................................................................4
Mounting the Surface Enclosure ...................................................................................................................4
Trim Ring (Where specified) .........................................................................................................................6
Installing the Trim Ring .................................................................................................................................7
Fixing the Enclosure Back Box to Trim Ring.................................................................................................8
Mounting the Flush Enclosure.......................................................................................................................9
Cabling ..........................................................................................................................................................10
Connecting to the Annunciator ......................................................................................................................11
Powering the Annunciator .............................................................................................................................11
Wiring Scheme..............................................................................................................................................12
Cable Length.................................................................................................................................................12
Cable Type.................................................................................................................................................... 13
Cable Entry ................................................................................................................................................... 13
Section 4
Configuration 14
To Set the address ........................................................................................................................................14
To Auto-learn the Annunciator ......................................................................................................................14
Download a Configuration.............................................................................................................................15
To Upload a Configuration via USB Drive.....................................................................................................15
Upload a Configuration via a PC ...................................................................................................................15
Test the Installation .......................................................................................................................................15
Section A
Specifications 16
Electrical........................................................................................................................................................16
Communication .............................................................................................................................................16
Mechanical ....................................................................................................................................................16
www.acornfiresecurity.com
www.acornfiresecurity.com
Introduction 1
Man-1161EN Rev. 01
Taktis Vision Installation & Operation Manual
1
Section 1
Introduction
TheTaktis Vision Annunciator is a display and control unit which duplicates the indications and primary controls of
Taktis Fire Alarm Control Panels connected to the same network.
The Annunciator connects to the FACP (Fire Alarm Control Panel) via the network interface and requires that the
main control panel have an network card fitted. For full details of Taktis networking refer to Taktis Installation Manual.
The Annunciator is connected to the network and any number of repeaters can be connected up to the maximum
number of nodes allowed by the network specification, which is 128 (including control panels).
In addition to displaying the status of the fire alarm system, the Annunciator can provide limited local control func-
tions via local control outputs.
Taktis Vision Annunciator Features
• Full colour 7” (800 x 480 pixel) GUI (Graphical User Interface).
• Replicates information displayed at the FACP.
• Automatic display brightness adjustment.
• Internal buzzer attenuate.
• Connects via control panel network terminals.
• Low current, 24V DC powered.
• Configurable functionality.
• Enable key-switch.
• Sheet steel enclosure.
• Surface, flush or semi flush enclosure options available.
Related Documentation
For information relating to the Taktis Fire Alarm Control Panel please refer to the following manuals::
Using your Smart-phone, tablet or device install a third party QR Code Reader and scan the code to view the doc-
uments.
Manual Variant Website
Installation Manual http://www.kentec.co.uk/manuals/man-1154GEN.pdf
Operation Manual http://www.kentec.co.uk/manuals/man-1169GEN.pdf
Installation Manual Operation Manual
www.acornfiresecurity.com
www.acornfiresecurity.com
Overview 2
Man-1161EN Rev.01
Taktis Vision Installation & Operation Manual
2
Section 2
Overview
This section provides a general overview of the Annunciator features.
The diagrams in this section refer to the surface enclosure variant. A ‘flush’ enclosure variant is also available.
Fascia Layout
The diagram below shows the Annunciator fascia layout.
Figure 2-1
Fascia Layout
ID Description ID Description
AEnclosure lid fixing screw EDisplay ambient light sensor
BEnclosure lid FEnclosure hinge
CTouch panel display GEnclosure knock-out (for cable entry)
DEnable keyswitch (Enables Access Level 2) HEnclosure back box
58.2
170.0
235.0
A
B
C
D
E
F
G
H
www.acornfiresecurity.com
www.acornfiresecurity.com
Overview 2
Man-1161EN Rev. 01
Taktis Vision Installation & Operation Manual
3
Internal Features
The diagram below shows the Annunciator internal features.
Figure 2-2
Internal Features
Key Description Key Description
AUSB port HBuzzer
B24 V In/Out, Remote PSU monitor & Ground
Te r m i n a l s
JProprietary connections for manufacturing purposes
CReboot button (panel firmware dependent) KSD card slot
DWrite Enable switch LNo function
ENo function MNo function
FNo function N Network terminals (Net in, Net out)
GProcessor reset button PNot used
QUSB to PC communications port
BA
QP N M
CD EF G H J
K
L
www.acornfiresecurity.com
www.acornfiresecurity.com
Installation 3
Man-1161EN Rev.01
Taktis Vision Installation & Operation Manual
4
Section 3
Installation
Before You Begin
Before you begin the installation, take a few minutes to review the installation information, gather the required items,
and complete the tasks listed below.
General Installation Checklist
To complete the installation:
Mounting the Surface Enclosure
1/ Open the enclosure by removing the screw located at the top-centre. The enclosure lid hinges downwards. Re-
move hinge pins by pulling inwards. Disconnect earth wire and put enclosure lid safely to one side.
Figure 3-1
Opening the Enclosure
1Create a plan and checklist before beginning the installation process. Planning can reduce the number of problems
that can occur during installation.
2 Select an environment that is suitable for operating the Annunciator. The site for mounting should be clean and dry
and not subject to excessive shock or vibration.
1 Create a plan of the fire alarm system and checklist for installing the Annunciator.
2 Remove the Annunciator from its packaging and check its contents.
3 Remove enclosure lid and temporarily store in a safe place.
4 Fix enclosure back box to wall.
5 Make network connection and dress the wires.
6 Ensure that the enclosure is free from wire ends, knockout discs and other debris.
7 Refit the enclosure lid.
8 Configure the Annunciator.
9 Test the installation.
CAUTION!
The installation must be performed by qualified personnel familiar with electronic components. Electronic compo-
nents within are vulnerable to damage from electrostatic discharge. Ground straps must be worn by installers
before handling circuit boards to prevent damage from electrostatic discharge.
www.acornfiresecurity.com
www.acornfiresecurity.com
Installation 3
Man-1161EN Rev. 01
Taktis Vision Installation & Operation Manual
5
2/ Using the enclosure back box as a template, mark the position of the fixing holes, ensuring that the wall is flat at
the chosen location. Fix the enclosure back box using suitable fixings, through all fixing points.
Figure 3-2
Surface Enclosure Back Box Dimensions
Ø5.0
ALL DIMENSIONS IN MM
NOT TO SCALE
51.6 167.8
230.6
115.5
190.6
Ø5.0
www.acornfiresecurity.com
www.acornfiresecurity.com
Installation 3
Man-1161EN Rev.01
Taktis Vision Installation & Operation Manual
6
Trim Ring (Where specified)
The optional trim ring allows semi-flush fitting of the surface enclosure back box. The diagram below shows the trim
ring external and advised wall cut-out dimensions.
Figure 3-3
Optional Trim Ring Dimensions
Note: 175mm X 240mm are the advised wall cut-out dimensions.
The diagram below shows side view of the enclosure within the trim ring.
Figure 3-4
Trim Ring with Enclosure in Place
256.6
38.7
240.0
197.4
175.0
ALL DIMENSIONS IN MM
NOT TO SCALE
21.7
www.acornfiresecurity.com
www.acornfiresecurity.com
Tabla de contenidos
Otros manuales de Alarma de incendios de Kentec Electronics
Kentec Electronics
Kentec Electronics Taktis Manual de usuario
Kentec Electronics
Kentec Electronics Sigma A-CP Manual de usuario
Kentec Electronics
Kentec Electronics Syncro Manual de usuario
Kentec Electronics
Kentec Electronics K25800 Series Guía
Kentec Electronics
Kentec Electronics Taktis Manual de usuario
