Kennedy ILR236 Manual de usuario
36 LED INSPECTION LAMP
WITH SWIVEL CLAMP
RECHARGEABLE
MODEL ILR236
KEN-503-5040K
INSTRUCTION MANUAL
www.kennedy-tools.co.uk
IMPORTANT NOTICE
YOU MUST FULLY CHARGE THE
INSPECTION LAMP BEFORE INITIAL USE.
SEE PAGE 3.
Ideal for use in engine bays and other low light
work areas.
Lasts up to 4 hours
when fully charged.
Ball-jointed swivel
clamp gives maximum
positioning versatility.
Convenient grip
mounted ON/OFF
switch.
Oil, petrol and UV
resistant.
Durable and robust
construction.
High light output.
Rubber handle.
Supplied with mains
charger.
QUALITY GUARANTEE & WARRANTY
KENNEDY TOOLS carry a one year manufacturers warranty.
KENNEDY TOOLS are designed & manufactured
to the highest standards & specifications.
Assuring the quality and performance required by all sectors of industry.
KENNEDY TOOLS are fully guaranteed against
faulty materials & workmanship.
Should they be found to be defective, they will either be repaired or replaced
free of charge (fair wear and tear and/or misuse excepted).
Please retain supplier invoice as proof of purchase.
© The Kennedy Group Ltd. 10/08
KENNEDY TOOLS
Wigston Works, Leicester, England.
Kennedy is a registered trade mark of The Kennedy Group Ltd.
AVAILABLE FROM YOUR DISTRIBUTOR
Whilst every effort has been made to ensure the accuracy of information contained in this instruction manual,
the Kennedy Tools policy of continuous improvement determines the right to change data, specifications and
component parts without prior notice.
Always dispose of unwanted tools, accessories and packaging materials in an
environmentally friendly manner.
For EU and EEA countries only.
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE) and its implementation in accordance with national law, electrical
goods that have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Do not dispose of electrical goods with domestic waste materials as inappropriate
disposal may cause potential hazards to the environment and human health.
For further information, please contact your local authority or the retailer from whom
you purchased the product.
THE ENVIRONMENT
2 3
KENNEDY
thoroughly recommends reading these instructions before using the
Inspection Lamp, even if you have used one before. Reading these instructions
carefully and understanding them fully will enable you to perform tasks correctly and
will prevent injury to yourself or someone else as well as prevent damage to the
vehicle and equipment. Please keep this instruction manual in a safe place for future
reference.
SAFETY GUIDELINES
Always keep children and unauthorised persons away from the working area.
Always run vehicle engines in a well ventilated area.
Always wear appropriate Personal Protective Equipment (PPE). Wear gloves when working
with engine components.
Never use other chargers to charge this Inspection Lamp. Only use the one which is
supplied in the box.
Never use whenever flammable gasses are present such as when the vehicle battery is
being charged, petrol fumes, solvents, spray paints, etc.
Never look directly at the LEDs, shine directly at other person’s or animal’s eyes.
Never allow children to use the Inspection lamp.
Never move the Inspection Lamp whilst it is being charged.
Never use if any parts are missing or damaged.
Never modify the Inspection Lamp or the charger in any way.
Never clamp the Inspection Lamp onto electrical wiring or any components that move
or are hot.
ELECTRICAL SAFETY
In the United Kingdom, the ELECTRICITY AT WORK ACT 1989 requires all portable electrical
appliances, if used on business premises, to be tested by a qualified electrician, using a
Portable Appliance Tester (PAT), at least once a year. The HEALTH & SAFETY AT WORK ACT
1974 makes owners of electrical appliances responsible for the safe condition of the
appliance and the safety of its operator. If in any doubt about electrical safety, contact a
qualified electrician.
ELECTRICAL SAFETY
An RCCB (Residual Current Circuit Breaker) should be fitted in the mains electricity distribution
board. If the power supply is not protected by an RCCB, it is highly recommended that an RCD
(Residual Current Device) is used with all portable electrical products.
UNPACKING
It is recommended that you save the packaging material for future transportation of the
Inspection Lamp in the event of service or repair.
Packaging materials especially bags, must be kept well away from babies and children.
QUALITY KENNEDY AUTOMOTIVE PRODUCTS AVAILABLE FROM YOUR DISTRIBUTOR
SPECIFICATIONS
Model number . . . . . . . . . . . . . . . . . . . .ILR236
Order code number . . . . . . . . . . .KEN-503-5040K
LED intensity at 50cm . . . . . . . . . . . . . .700Lux
Charging time . . . . . . . . . . . . . . . . . . . . .3.5hrs
Operating time . . . . . . . . . . . . . . . . . . . . . .4hrs
Charger input . . . . . . . . . . . . . . . . .230V~ 50Hz
Charger output . . . . . . . . . . . . . .9V DC 600mAh
Operating voltage . . . . . . . . . . . . . . . . . . . .3.3V
Operating temperature . . . . . . . . . . .0°C to 40°C
Battery . . . . . . . . . . . . .4 x AA Ni-MH 1,800mAh
Moisture protection . . . . . . . . . . . . . . . . . .IP20
Net weight (Inspection Lamp only) . . . . . .655g
CHARGING
The charger is for indoor use only.
Charge the battery for more than 10 hours before initial use.
Recharge fully once a month when not in use.
When in use, all 36 LEDs flash on and off 3 times to warn that the Inspection Lamp will soon
need recharging.
When a small red LED comes on in the centre of the lens, this means that the battery is
becoming discharged and that it needs charging.
The inspection lamp will not work whilst it is being charged.
1. Plug the charger into a mains socket.
2. Connect the lead from the charger to the charging point on the end of the rubber handle of
the Inspection Lamp and switch the mains power on.
3. A small LED in the centre of the lens will change from red to green and back to red to
indicate that charging is taking place.
4. When charging is complete, the LED will change from red to green. Switch the mains power
off, disconnect the charger from the Inspection Lamp and store the charger in a safe place.
N.B. If the red LED is still on after 3hrs, unplug and try charging again.
OPERATING
1. Mount the Inspection Lamp to a secure position using the clamp. Adjust the angle of the
Inspection Lamp by holding the main body and the clamp firmly in each hand and manoeuvre
until the desired position is achieved.
2. Press the red button on the top of the rubber grip handle once to switch on and again to
switch off.
Otros manuales de Flash de Kennedy
