Kenmore 110.44832 200 Manual de usuario

Sears Kenmore/Whirlpool Front Load Washer

Error Codes: 02F dLF

Model: 110.44832 200 (110. = Whirlpool)

S/N: CSP 1903874

Type: 199-AKP 705/WT

SOURCE: www.applicancepartspros.com

WHIRLPOOL FAULT CODES

Whirlpool Duet Front Loading Automatic Washer Fault Codes

Failure

Code Fault Code Description Solution

FH No water detected entering

machine or Pressure switch trip

not detected.

If after 30 seconds the control does not detect water

entering machine and then valves will be turned off and

the error code will be displayed.

If the control has turned the water valves on and after 8

minutes the flow meter has detected 10.5 gallons of

water passing through it, but has not detected the

pressure switch trip, the valves will be turned off and the

error code will flash.

Press PAUSE/CANCEL twice to clear the display.

Potential Causes

• If there is no water in the unit:

- Make sure that both valves at the water source(s) are

turned on all the way.

- Check for plugged or kinked inlet hoses or plugged

screens in the inlet valves

- Verify inlet valve operation

• If there is water in the unit:

- Verify Drain pump operation

- Pressure Switch Hose is in good condition and

properly connected to Tub and Pressure switch

• Verify there is not a siphon problem

• Verify wire harness connections to; Inlet Valves,

Pressure Switch, Drain Pump, Flow Meter, and Central

Control Unit (CCU)

• Check all hoses for possible leaks

• Verify pressure switch operation

• Verify flow meter operation

• Verify CCU operation

Replace failed component.

F02 Long Drain If the drain time exceeds 8 minutes, the water valves are

turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed,

then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or

kinked

• Check the electrical connections at the pump and make

sure the pump is running.

• Check the drain pump filter for foreign objects

• If the above does not correct the problem replace the

pump

F05 Water temperature sensor error If during the water heating step in the wash cycle, the

water temperature sensor (NTC) value is out of range, or

the heating element circuit has failed, the F05 error code

will be displayed.

Potential Causes

• Check the Water Temperature Sensor, Heating Element

and Element Relay

• Check connections to the Sensor, Heating Element and

Relay

Replace failed component.

F06 Drive motor tachometer error The control is unable to properly detect motor speed and

the machine will shut down. If a failure occurs during

high-speed spin the door will be unlocked after 3

minutes.

Potential Causes

• Check wire harness connections between the Drive

Motor/Tachometer and the Motor ControlUnit (MCU), and

between the MCU and the Central Control Unit (CCU)

• Check the Drive Motor

• Check the MCU

• Check the Wire Harness

Replace failed component.

F07 Motor control unit error The Central Control Unit has detected a short in the

motor control unit. If a failure occurs during high-speed

spin the door will be unlocked after 3 minutes.

Potential Causes

• Check wire harness connections between the Drive

Motor and the Motor Control Unit (MCU), and between

the MCU and the Central Control Unit (CCU)

• Check the MCU

• Check the Drive Motor

• Check the Wire Harness

Replace failed component.

F09 Overflow condition If the Overflow contact on the pressure switch is Closed

for more than 60 seconds an Overflow condition will

occur. In an Overflow condition, the Door will remain

locked, and the Drain Pump will run constantly, even if

PAUSE/CANCEL is pressed twice and the Display is

cleared. Unplug the unit to service.

Potential Causes

• Check the drain hose and make sure it is not plugged or

kinked

• Check Wire Harness connections to the Drain Pump,

Pressure Switch, and Central Control Unit (CCU)

• Check / Clean Drain Pump Filter of foreign objects

• Check for Drain Pump Failure

• Check the Inlet Valve for proper shut off

• Check the Pressure switch for proper operation

Replace failed component.

F10 Motor Control Unit (MCU) heat

sink thermal trip If the thermal protector on the MCU heat sink gets too

hot, it will open the thermal protector on the heat sink

which will stop motor functions and an F10 will be

displayed.

Potential Causes

• Check for Proper Installation, verify the unit is not

located near a source of heat and has proper ventilation.

• Check Wire Harness connections to the MCU, the

motor, and Central Control Unit (CCU)

• Check the Drive system for any worn or failed

components

• Check MCU

• Check Motor

Replace failed component.

F11 Serial communication error Communication between the Central Control Unit (CCU)

and the Motor Control Unit (MCU) cannot be sent

correctly.

Potential Causes

• Check Wire Harness connections to the MCU, the

motor, and Central Control Unit (CCU)

• Check the Drive system for any worn or failed

components

• Check MCU

• Check CCU

• Check Motor

• Check Wire Harness

Replace failed component.

F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s

proper position.

Potential Causes

• Check mechanical linkage from dispenser motor to the

top of the dispenser.

• Check Wire Harness connections to the dispenser

motor and Central Control Unit (CCU)

• Check Dispenser Motor

Replace failed component.

F14 EEPROM error The Central Control Unit (CCU) receives it’s data from an

EEPROM onboard the CCU. If there is an error reading

this data it will cause this error.

Potential Causes

• A power glitch may cause this error. Try unplugging the

Unit for two minutes to see if that fixes the error.

• Check CCU.

Replace failed component.

F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a

wash cycle it will go into this error mode.

Potential Causes

• Check Wire Harness connections to the MCU, the

motor, and Central Control Unit (CCU)

• Check Drive belt

• Check MCU

• Check Motor

• Check Wire Harness

Replace failed component.

Sud SUDS LOCK (Overdose of

detergent detected during the

wash cycle)

The motor control unit senses a suds lock condition by

analyzing the current draw on the drive motor. If “Sud” is

displayed a potential suds lock is detected. This may

signify a bad pump, an extra heavy load, excessive

detergent, or excessive suds.

Potential Causes

• If too much detergent was used, run the unit through a

Rinse/ Spin cycle then a Normal cycle without adding any

detergent. This should clear the unit of the excess

detergent.

• Check the drain hose and make sure it is not plugged or

kinked

• Check Wire Harness connections to the Drain Pump,

Pressure Switch, and Central Control Unit (CCU)

• Check / Clean Drain Pump Filter of foreign objects

• Check Drain Pump

• Check the Pressure Switch

• Check CCU

Replace failed component.

FdL Door lock error A Door Lock Error occurs if the door cannot be locked. It

will try to lock it 6 times before displaying the error.

Potential Causes

• Door Lock Mechanism broken or removed from the

Door

• Check Door Lock/Switch Assembly

• Check the wire harness connections to the Door

Lock/Switch Assembly and Central Control Unit (CCU)

• Door Lock/Switch Assembly Failure

Replace failed component.

FdU Door unlock error A Door Unlock Error occurs if the door cannot be

unlocked. It will try to unlock the door 6 times before

displaying the error.

Potential Causes

• Door Lock Mechanism broken.

• Check Door Lock/Switch Assembly for foreign objects

• Check Wire Harness connections to the Door

Lock/Switch Assembly and Central Control Unit (CCU)

• Door Lock/Switch Assembly Failure

Replace failed component.

Note: The door lock/switch assembly can be manually

unlocked.

To Manually unlock the door lock system:

1. Unplug the power cord from the outlet.

2. Remove the lower toe panel.

3. Reach up along the inside of the front panel and locate

the bottom of the door latch assembly.

4. Located on the bottom of the door latch assembly is a

tear-drop shaped tab.

5. Gently pull the tab down about 1/4 inch or until a click

is heard.

6. The door may now be opened.

Tabla de contenidos

Otros manuales de Arandela de Kenmore

Kenmore

Kenmore 110.2803 Series Manual de usuario

Kenmore

Kenmore 110.2649 Series Manual de usuario

Kenmore

Kenmore 796.4154 Series Manual de usuario

Kenmore

Kenmore 796. 4139 series Manual de usuario

Kenmore

Kenmore 796.4027 Series Manual de usuario

Kenmore

Kenmore 417.4413 Manual de usuario

Kenmore

Kenmore 5062 Series Manual de usuario

Kenmore

Kenmore 110.2963 Series Manual de usuario

Kenmore

Kenmore 796.4138 series Manual de usuario

Kenmore

Kenmore Kenmore Electronic Three-Speed Automatic... Instrucciones de funcionamiento

Kenmore

Kenmore 110.1611 Series Manual de usuario

Kenmore

Kenmore 110.2783 Series Manual de usuario

Kenmore

Kenmore Kenmore One-Speed Automatic Washers Instrucciones originales

Kenmore

Kenmore 20842 & 20847 Manual del propietario

Kenmore

Kenmore 110.29727800 Manual de usuario

Kenmore

Kenmore 796.488x2800 Manual de usuario

Kenmore

Kenmore 48102 Manual de usuario

Kenmore

Kenmore Front Load Washer Manual de usuario

Kenmore

Kenmore 796.4126 Series Manual de usuario

Kenmore

Kenmore 2130 Manual de usuario

Kenmore

Kenmore One-speed automatic washers with water temperature... Instrucciones de funcionamiento

Kenmore

Kenmore Elite 796.3142 Manual de usuario

Kenmore

Kenmore 41724182301 Manual de usuario

Kenmore

Kenmore 110.2713 Series Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario