Kendal Lighting AC-21052 Manual de usuario

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

C.E.T.L. LISTED MODEL: CF552B-PEN

Weight of Fan: 7.30Kgs

KENDALLIGHTING

Kendal Lighting (BC) Inc.

#110, 6780 Dennett Place

Delta, BC V4G 1N4

Canada

Tel: (604) 952-5510

Fax: (604) 952-5513

Model: AC-21052

2. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items;

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

1. TOOLS AND MATERIALS

REQUIRED

a. Hanger bracket

b. Canopy

c. Canopy cover

d. Coupling cover

e. Downrod assembly

f. Fan housing

g. Fan motor assembly

h. 17W LED assembly

i. Blade set (5)

j. Receiver + 6 wire nuts

k. Transmitter

l. Transmitter holder

Transmitter holder mounting screw (2)

12V Battery

m. Package hardware

1) Blade screws (16), fiber washers (16)

2) Fan housing screws (5)

3) Mounting hardware:

wood screws(2),washers(2)

4) Balancing kit (1)

3. SAFETY RULES

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualified

licensed electrician.

3. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

4. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

5. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

6. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

7. Avoid placing objects in the path of the

blades.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX

MARKED "ACCEPTABLE FOR FAN

SUPPORT".

8. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

9. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the grounded conductor and

the equipment - grounding conductor on

one side of the outlet box.

11. Electrical diagrams are reference only.

Light kit that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

4. MOUNTING OPTIONS

If there isn't an existing CUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 35 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4.

Outlet box

Provide strong

support

Recessed

outlet box

Ceiling

mounting

plate

Outlet box

Figure 1

Figure 3

Figure 4

Outlet box

Figure 2

Angled ceiling

maximum

18 angle

Figure 5

5. ATTACHING THE FAN

BLADES

Step 1. Insert the blades through the slots on the

fan motor assembly.

Step 2. Attach the fan blades to the fan motor

assembly using the blade screws and fiber

washer and tighten them securely.

Step3. Repeat this step with the other blades.

NOTE: When installing the blades, ensure the

sides with “THIS SIDE UP” face the ceiling.

CAUTION: Make sure all screws are

tightened securely.

Blade screws

Fiber washers

Blade

Fan housing screws

Fan housing

Fan motor assembly

Fan motor assemby

THIS SIDE UP

Figure 6

6. ATTACHING THE FAN

HOUSING

Align holes in the housing and the fan motor

assembly, and secure with the screw. Ensure all

the screws are tightened.

Figure 9

Figure 8

Figure 10

Groove

Tab

7. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Pass the 120-volt supply wires through

the center hole in the ceiling hanger bracket as

shown in Fig. 7.

Step 2. Secure the hanger bracket to the

ceiling outlet box with the screws and washers

provided with your outlet box.

Downrod

Canopy

Set screws

Locking

Hanger pin

Coupling cover

Canopy cover

Figure 7

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

plate

CUL Listed

electrial

box

120V Wires

Washers

Step 7. Place the downrod ball into the hanger

bracket socket. And rotate until groove in

hanger ball lines up with tab in hanger bracket.

(You will feel hanger ball drop into place as

you rotate.) (Fig. 10)

Downrod

Set screw

Hanger ball

Cross pin

Hanger pin

Locking

Step 3. Loosen the two set screws from the fan

motor assembly coupling.

Step 4. Remove the hanger pin and lock pin from

the downrod. Remove the hanger ball from the

downrod by loosening the hanger ball set screw,

and removing the cross pin, then sliding the

hanger ball off of the downrod.

Step 5. Carefully feed the fan wires and safety

cable up through the downrod. Thread the

downrod into the fan motor assembly coupling.

Line up the holes and replace the lock pin and

hanger pin. Tighten the set screws.

Step 6. Slip the coupling cover, canopy cover,

and canopy onto the downrod. Carefully reinstall

the hanger ball onto the downrod, and ensure

that the cross pinis in the correct position, the

set screws are tight, and the wires are not

twisted.

8. MAKE THE ELECTRIC

CONNECTIONS

WARNING: To avoid possible electrical

shock, be sure electricity is turned off at the

main fuse box before wiring.

NOTE: This remote control unit is equipped

with 16 code combinations to prevent possible

interference from or to other remote units.

The frequency switches on your receiver and

transmitter have been preset at the factory.

Please recheck to make sure the switches on

transmitter and receiver are set to the same

position, any combination of settings will

operate the fan as long as the transmitter and

receiver are set to the same position. (Figure

11)

Step 1. (Fig. 12) Insert the receiver into the

mounting bracket with the flat side of the

receiver facing the ceiling.

Step 3. (Fig. 13) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white (neutral) wire from the

ceiling to the white wire marked "AC in N" from

the Receiver. Secure the wire connections

with the plastic wire nuts provided.

Figure 13

White (neutral)

Green or bare

copper (ground)

White (AC IN N)

White (to motor N)

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black (AC IN L)

Black (to motor L)

Blue (light)

Receiver

Blue (for light)

Black (motor)

Figure 11

Figure 12

Receiver

Hanger

bracket

Code switch

Step 4. (Figure 13) If your outlet box has a ground

wire (green or bare copper) connect it to the fan

ground wires; otherwise, connect the hanging

bracket ground wire to the hanger ball ground

wire. Secure the wire connection with a plastic

nut provided. After connecting the wires, spread

them apart so that the green and white wires are

on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the

wire connections up into the outlet box.

Step 2. (Fig. 13) Motor to Receiver Electrical

Connections: Connect the Black wire from the fan to

Black wire marked "TO MOTOR L" from the receiver.

Connect the White wire from the fan to the White wire

marked "TO MOTOR N" from the receiver. Connect

the Blue wire from the fan to the Blue wire marked

"For Light" from the receiver. Secure wire connec-

tions with the plastic wire nuts provided.

Note: Fan must be installed at a maximum

distance of 20 feet from the transmitting unit

for proper signal transmission between the

transmitting unit and the fan's receiving unit.

9. INSTALLATION OF

SAFETY CABLE

10. FINISHING THE

INSTALLATION

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to hanger bracket

and place the key hole on the canopy over the

screw on the hanger bracket, turn canopy until

it locks in place at the narrow section of the

key holes. (Fig.15)

Step 3. Align the circular hole on canopy with

the remaining hole on the hanger bracket,

secure by tightening the two set screws. Note:

Adjust the canopy screws as necessary until

the canopy and canopy cover are snug.

WARNING: Make sure tab at bottom of

hanger bracket is properly seated in groove of

hanger ball before attaching canopy to

bracket. Failure to properly seat tab in groove

could cause damage to electrical wiring.

Figure 14

Figure 15

Hanger bracket Safety cable

Outlet box

Hanger

bracket

Canopy

Canopy cover

Screws

An additional safety cable is provided to prevent

the fan from falling. Secure the safety cable to

the ceiling joist with screw and washer, as

illustrated in Figure 14.

11. ATTACHING THE 17W

LED ASSEMBLY

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box. Turning power

off using the fan switch is not sufficient to

prevent electric shock.

Figure 16

17W LED assembly

Step 1. While holding the 17W LED assembly

under your fan, firmly snap the wire connection

plugs together.

Step 2. Attach the 17W LED assembly to the

switch box by twisting tightly.

Note: This is an integrated LED light kit assembly

and can not be disassembled

to prevent electronic shock.

Switch box

Connection plugs

Figure 17

12. INSTALLING THE

TRANSMITTER

HOLDER

Attach the remote control holder with the two

remote control holder mounting screws.

(Fig.17)

13. INSTALLING THE

BATTERY

Install the 12volt battery into the hand held

transmitter (Figure 18) as shown in (Figure 19).

Make sure the battery is secure with the matching

+/- terminals.

14. OPERATING YOUR

TRANSMITTER

Restore power to ceiling fan and test for

proper operation.

A. HI, MED and LOW buttons:

These three buttons are used to set the

fan speed as follows:

= high speed

= medium speed

= low speed

MED

LOW

B. FAN OFF button:

This button turns the fan off.

C. LIGHT button:

This button controls the light. Press and

release the button to turn the light ON or

OFF. Press and hold the button to set the

desired brightness. The light key has an

auto-resume, it will stay at the same

brightness as the last time it was turned off.

Figure 18

Figure 19

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Kendal Lighting

Kendal Lighting

Kendal Lighting AC-19544 Manual de usuario

Kendal Lighting

Kendal Lighting AC-21152 Manual de usuario

Kendal Lighting

Kendal Lighting AC-20244 Manual de usuario

Kendal Lighting

Kendal Lighting AC-20452 Manual de usuario

Kendal Lighting

Kendal Lighting AC-24246 Manual de usuario

Kendal Lighting

Kendal Lighting AC6842B Manual de usuario

Kendal Lighting

Kendal Lighting AC-19856 Manual de usuario

Kendal Lighting

Kendal Lighting AC-30052 Manual de usuario

Kendal Lighting

Kendal Lighting AC-30552 Manual de usuario

Kendal Lighting

Kendal Lighting AC11152P-ORB/WN Manual de usuario

Kendal Lighting

Kendal Lighting AC-21750 Manual de usuario

Kendal Lighting

Kendal Lighting AC-24344 Manual de usuario

Kendal Lighting

Kendal Lighting AC-22656 Manual de usuario

Kendal Lighting

Kendal Lighting AC-22160 Manual de usuario

Kendal Lighting

Kendal Lighting AC-23856 Manual de usuario

Kendal Lighting

Kendal Lighting Lopro KENAC21352SN Manual de usuario

Kendal Lighting

Kendal Lighting AC-21852 Manual de usuario

Kendal Lighting

Kendal Lighting AC-24060 Manual de usuario

Kendal Lighting

Kendal Lighting Triax AC-22352 Manual de usuario

Kendal Lighting

Kendal Lighting AC-20644 Manual de usuario

Kendal Lighting

Kendal Lighting AC-22552 Manual de usuario

Kendal Lighting

Kendal Lighting AC-19242 Manual de usuario

Kendal Lighting

Kendal Lighting AC-12452 Manual de usuario

Kendal Lighting

Kendal Lighting AC-22452 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje