Kemppi MasterTig 535ACDC Manual de usuario
MasterTig 535ACDC
Operating manual - EN
MasterTig 535ACDC
MasterTig Cooler MXL
© Kemppi 11921940 / 2140
MasterTig 535ACDC
Operating manual - EN
CONTENTS
1. General 4
1.1 Equipment description 5
2. Installation 7
2.1 Installing mains plug 8
2.2 Installing cooling unit (optional) 9
2.3 Installing equipment on cart (optional) 12
2.4 Connecting TIG torch 15
2.5 Connecting earth return cable and clamp 17
2.6 Connecting MMA electrode holder 18
2.7 Installing remote control (optional) 19
2.8 Installing gas bottle 22
2.9 Installing gas bottle on cart 23
2.10 Replacing control panel 24
2.11 Lifting MasterTig 535 equipment 28
3. Operation 30
3.1 Operating power source 31
3.2 Operating control panel MTP35X 32
3.2.1 Home view 33
3.2.2 Weld Assist view 34
3.2.3 Memory channels view 38
3.2.4 Start & stop sequence view 39
3.2.5 Pulse view 41
3.2.6 Current mode view 43
3.2.7 Settings view 44
3.2.8 Info view 47
3.2.9 Screen saver 48
3.3 Operating cooling unit 49
3.4 Remote control 50
4. Maintenance 52
4.1 Troubleshooting 53
4.1.1 Error codes 54
4.2 Disposal 56
5. Technical data 57
5.1 Power source MasterTig 535ACDC 58
5.2 Cooling unit MasterTig Cooler MXL 60
5.3 TIG guide tables 61
5.4 Welding processes and features 62
© Kemppi 21921940 / 2140
MasterTig 535ACDC
Operating manual - EN
1. GENERAL
These instructions describe the use of Kemppi's MasterTig 535ACDC welding power source. The system consists of
MasterTig power source with MTP35X control panel (factory installed), optional MasterTig Cooler MXL water cooler,
optional transport unit and Flexlite TX TIG welding torch.
Important notes
Read the instructions through carefully. For your own safety, and that of your working environment, pay particular atten-
tion to the safety instructions delivered with the equipment.
Items in the manual that require particular attention in order to minimize damage and harm are indicated with the
below symbols. Read these sections carefully and follow their instructions.
Note: Gives the user a useful piece of information.
Caution: Describes a situation that may result in damage to the equipment or system.
Warning: Describes a potentially dangerous situation. If not avoided, it will result in personal damage or fatal injury.
DISCLAIMER
While every effort has been made to ensure that the information contained in this guide is accurate and com-
plete, no liability can be accepted for any errors or omissions. Kemppi reserves the right to change the spe-
cification of the product described at any time without prior notice. Do not copy, record, reproduce or transmit
the contents of this guide without prior permission from Kemppi.
© Kemppi 41921940 / 2140
MasterTig 535ACDC
Operating manual - EN
1.1 Equipment description
Kemppi MasterTig 535 AC/DC welding equipment is designed for professional industrial use, with characteristics espe-
cially suitable for welding materials like aluminum and stainless steel. The multipurpose MasterTig power source is suit-
able for MMA welding, TIG welding and pulsed TIG welding with both direct current (DC) and alternating current (AC).
Power source model:
•MasterTig 535ACDC GM, multi-voltage and generator compatible (500 A AC/DC) *
* A dedicated VRD(Voltage Reduction Device)model version, where the VRD function is locked on, is also available.
Control panel:
•MTP35X control panel (AC/DC, 7" TFT LCD display panel).
Equipment:
1. MasterTig 535 power source
2. MasterTig Cooler MXL (optional)
3. TIG torch
4. Electrode holder
5. Earth return cable and clamp
6. Remote control (wired or wireless)
7. Foot pedal remote control (wired or wireless)
8. Lifting eyes
9. Power ON/OFFswitch.
Connections:
a. External remote control connector
b. TIG welding cable connector (connection type R1/4)
c. Control cable connector
d. DIX connector (-)
e. DIX connector (+)
f. Coolant liquid inlet and outlet (color-coded)
g. Gas hose connection
© Kemppi 51921940 / 2140
MasterTig 535ACDC
Operating manual - EN
h. Mains cable
i. Cooling unit connection.
EQUIPMENT IDENTIFICATION
Serial number
Serial number of the device is marked on the rating plate or in another distinctive location on the device. It is
important to make correct reference to the serial number of the product when ordering spare parts or making
repairs for example.
Quick Response (QR) code
Device-related information or a web link to such information may be found in the form of a QR code on the
device. The code can be read, for example, with a mobile device camera and a QR code application.
© Kemppi 61921940 / 2140
MasterTig 535ACDC
Operating manual - EN
2. INSTALLATION
Do not connect the equipment to the mains before the installation is complete.
Do not attempt to move or hang the equipment mechanically (e.g. with a hoist) from the handle on the power
source unit. The handle is meant only for manual moving when the equipment is installed on a cart.
Place the machine on a horizontal, stable and clean ground. Protect the machine from rain and direct sunshine.
Check that there is enough space for cooling air circulation in the machine vicinity.
Before installation
•Make sure to acknowledge and follow the local and national requirements regarding installation and use of high
voltage units.
•Check the contents of the packages and make sure the parts are not damaged.
•Before you install the power source on site, see the requirements for the mains cable type and fuse rating given in
the "Technical data" on page57 chapter.
Distribution network
MasterTig 535ACDC: Provided that the public low voltage short circuit power at the point of common coupling is
higher than or equal to the value stated on the list below, this equipment is compliant with IEC 61000-3-11 and IEC
61000-3-12 and can be connected to public low voltage systems. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if necessary, that the system impedance
complies with the impedance restrictions.
•MasterTig 535ACDC: 3.4 MVA
According to the EMC classification (Class A), the MasterTig equipment is not intended to be used in residential loc-
ations where the electrical power is provided by the public low-voltage supply system.
© Kemppi 71921940 / 2140
MasterTig 535ACDC
Operating manual - EN
2.1 Installing mains plug
Only an authorized electrician is allowed to install the mains cable and plug.
Do not connect the machine to the mains before the installation is complete.
Install the 3-phase plug according to the MasterTig power source and site requirements. Refer also to "Technical data"
on page57 for power source specific technical information.
© Kemppi 81921940 / 2140
MasterTig 535ACDC
Operating manual - EN
2.2 Installing cooling unit (optional)
For instructions on installing the equipment on cart, refer to "Installing equipment on cart (optional)" on page12.
The cooling unit must be installed by authorized service personnel.
Do not attempt to move the power source with a hoist from its handle. The handle is meant for moving the equip-
ment when installed on cart.
Tools needed:
1. Remove the power source's rear cover.
© Kemppi 91921940 / 2140
MasterTig 535ACDC
Operating manual - EN
2. Route the cooling unit's connection cables so that they remain accessible through the next steps.
3. Lift the power source with a hoist from the lifting eyes and place it on top of the cooling unit so that the fixing
plates align and go into their slots. Fix the units together with two screws in the front and two screws in the rear.
Ensure that the cooling unit's connection cables are not caught and/or damaged between the edges.
© Kemppi 10 1921940 / 2140
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Sistema de soldadura de Kemppi
Kemppi
Kemppi FastMig X 450 Manual de usuario
Kemppi
Kemppi FitWeld 300 Manual de usuario
Kemppi
Kemppi M 420 Manual de usuario
Kemppi
Kemppi WeldForce KPS 3500 MVU Manual de usuario
Kemppi
Kemppi MasterTig MLS 2500 Manual de usuario
Kemppi
Kemppi HiArc M 400A Manual de usuario
Kemppi
Kemppi Minarc Evo 180 Manual de usuario
Kemppi
Kemppi KEMPOWELD 4200 Manual de usuario
Kemppi
Kemppi A3 MIG Manual de usuario
Kemppi
Kemppi FASTMIG MS 200 Manual de usuario
Kemppi
Kemppi Kempact MIG 2530 Manual de usuario
Kemppi
Kemppi KEMPACT Manual de usuario
Kemppi
Kemppi MLS 2300 ACDC Manual técnico
Kemppi
Kemppi A5 MIG 1500 Manual de usuario
Kemppi
Kemppi KEMPACT 251R Manual de usuario
Kemppi
Kemppi Master S 400 Manual de usuario
Kemppi
Kemppi PROMIG EVOLUTION 511 Manual de usuario
Kemppi
Kemppi Kempomat 2500 Manual de usuario
Kemppi
Kemppi MinarcTig Evo 200 Manual de usuario
Kemppi
Kemppi KEMPOMAT 163 S Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
ESAB
ESAB Buddy Arc 145 Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
