Kemlan CUBE Manual
Specialists in fireplace design and manufacture
KEMLAN CUBE
INSTALLATION & OPERATING INSTRUCTIONS
IMPORTANT:
INSTALLER, PLEASE LEAVE THESE INSTRUCTIONS WITH THE UNIT ON COMPLETION.
10 YEAR FIREBOX WARRANTY
The firebox is covered by a 10 year warranty.
Other parts are covered by a one year limited warranty.
Head Office –13 French Avenue, Brendale, Queensland 4500
Telephone –PH: (07) 3490 5500
Facsimile –FAX: (07) 3490 5520
Website: - www.jetmaster.com.au
Business hours: - Monday to Thursday 7:30am-4:00pm. Friday 7:30am-2:00pm
Email: - sales@jetmaster.com.au
DIMENSIONS
KEMLAN CUBE
A
B
C
D
F
E
G
H
A B C D E F G H
MEASUREMENT 522 499 705 510 218 353.5 568 526
Ver.20
450
06/06/2023 2
D
G
K
E
B
H
C
C
F
F
J
A B C D E F G H I J K
MEASUREMENT 120 300 125 338 654 540 1004 875 1114 570 300
I
MINIMUM CLEARANCES:
K
A
MINIMUM CLEARANCES FOR THE
KEMLAN CUBE
INSTALLED WITH DEFAULT FLUE KIT
Ver.20
1007
920
260 927 300
STEEL BENCH MEASUREMENTS:
FRONT VIEW
TOP VIEW
40
06/06/2023 3
Ver.20
HEARTH MEASUREMENT
B
A
Cube
A. UNIT HEIGHT ABOVE FLOOR 300 MIN.
B. HEARTH DIMENSION FORWARD OF UNIT 300
90
120
06/06/2023 4
Ver.20
AIR GAP DETAIL
06/06/2023
NOTE:- When installing this unit onto a table, make sure to leave the
4x bolts in place. The bolts are necessary to allow air flow to the
underside of the firebox. The removal of these bolts will lead to
overheating to the underside of the unit and eventually cause
malfunction. The removal of these bolts could void your warranty.
5
Ver.20
AIR GAP DETAIL
06/06/2023
The bolts will need to be removed when the appliance is installed onto a meridian
base. However, the same bolts must be used to fix appliance to the meridian base.
Air gap
There must be an air gap between the bottom of the appliance and the top of a
table. This is necessary to allow air flow to the appliance.
Meridian base
Table
6
Run a bead of silicone down
the vertical seam of the outer
casing to the flashing
10” Flue
KEMLAN CUBE
FLAT CEILING INSTALLATION
6” Flue
Flash roof to outer casing
(supplied by installer)
INSTALLATION INSTRUCTION
Pop rivet or
screw brackets to
the outside of the
outer casing
Short tube fits into flue
pipe. All flues should
be trimmed level
DETAIL A
8” Decro with double heat shield
A
Stainless steel flue pipe.
All flue pipes must be
connected with pop rivets
supplied by installer
All casing flue pipes must
be connected with pop
rivets supplied by installer
Flue system to be installed
to suit AS/NZS 2918.2001
Vented cap
B
Support outer flue with
Brackets supplied
Bracing supplied by installer
NOTE:- When Decromesh / Heatshield is fitted, it must
finish a minimum of 600mm below the ceiling or extend
through the ceiling drop box into the outer flue casing
8” Flue
c
DETAIL
c
D
DETAIL
c
All
8”-10” assembled flues must
have the crimps pointing upwards
crimped
plain
All 6” assembled flues must have
the crimps pointing downwards
crimped
plain
DETAIL D
Ver.20
06/06/2023 7
25
12mm
Air gap
Ceiling trim
DETAIL B
25
25
150
Run a bead of silicone down
the vertical seam of the outer
casing to the flashing
Raked ceiling trim
KEMLAN CUBE
RAKED CEILING INSTALLATION
Flash roof to outer
casing
(supplied by installer)
INSTALLATION INSTRUCTION
Pop rivet or
screw brackets to
the outside of the
outer casing
Short tube fits into flue
pipe. All flues should
be trimmed level
DETAIL A
DETAIL B
A
Stainless steel flue pipe.
All flue pipes must be
connected with pop rivets
supplied by installer
Flue system to be installed
to suit AS/NZS 2918.2001
25
Vented cap
B
Bracing supplied by installer
All casing flue pipes must
be connected with pop
rivets supplied by installer
12mm
Air Gap
8” Decro with double
heat shield
10” Flue
6” Flue
NOTE:- When Decromesh / Heatshield is fitted, it must
finish a minimum of 600mm below the ceiling or extend
through the ceiling drop box into the outer flue casing
8” Flue c
DETAIL
c
All
8”-10” assembled flues must
have the crimps pointing upwards
D
DETAIL D
All 6” assembled flues must have
the crimps pointing downwards
crimped
plain
crimped
plain
Ver.20
06/06/2023 8
Ver.20
SUPER NOVA / CUBE /TEMPO GRAND
BAFFLE PLATE INSTALLATON INSTRUCTIONS
1. MAKE SURE TO INSTALL AIR TUBE AS
REQUIRED. THE OPENING ON THE TUBE
END NEEDS TO BE AGAINST THE BACK
WALL. ALL ROUND EXIT HOLES MUST BE
POINTING TO THE BOTTOM OF THE FIRE
BOX OR THE SIDE WALLS.
2. CERAMIC BAFFLE PLATES SIZE
230mmX240mm. INSTALL THE BAFFLE
PLATE 230mm FRONT TO BACK, 240mm
SIDE TO SIDE. GET BAFFLE PLATE
INSIDE THE FIREBOX AND TILT ON AN
ANGLE. PUSH BAFFLE PLATE OVER
THE AIR TUBE
3. THEN MOVE SIDEWAYS UNTIL SUPPORTED
BY THE SUPPORT PLATE AND TOUCHING THE
SIDE WALL
4. REPEAT THE PROCESS FOR THE
OTHER SIDE. PUSH BOTH BAFFLE PLATES
UNTIL IT IS AGAINST THE SIDE AND REAR
WALLS.
06/06/2023 9
Ver.2006/06/2023 10
Tabla de contenidos
Otros manuales de Chimenea de interior de Kemlan
Kemlan
Kemlan 700 Low Line Manual de usuario
Kemlan
Kemlan Super Nova Freestanding Series II Manual
Kemlan
Kemlan Convectaire Manual de usuario
Kemlan
Kemlan XL Manual
Kemlan
Kemlan 700 Low Line Manual de usuario
Kemlan
Kemlan Super Nova Insert RF Manual
Kemlan
Kemlan Horizon 3 Sided Manual de usuario
Kemlan
Kemlan Power Flue Horizon Gas Fireplaces Manual de usuario
Kemlan
Kemlan Horizon Natural Draft Electronic Ignition Manual de usuario
Kemlan
Kemlan Tempo Stack Manual de usuario
