Kannad 406 AF-COMPACT Manual de usuario
DOC07089
A
0144618A
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 2
Check that your KANNAD 406 AF COMPACT Pack is composed of:
1. transmitter;
2. mounting bracket;
3. RC200 remote control panel;
4. DIN-12 connector;
5. SUB D 9 Pts Female connector.
Outside antenna (6) is purchased separately.
- Install ELT and bracket in the aircraft near the tail.
- Mount outside antenna on the fuselage near the tail and connect it to the ELT with a coaxial cable.
- Install remote control panel in the cockpit and fabricate a 3-wire bundle).
- Connect the ELT.
- Check and power the ELT.
1. CHECK PACK COMPOSITION
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 3
Determine the location of the ELT on board according to FAR/RTCA recommendations.
1. Fixed wings
Mount the KANNAD 406-AF COMPACT with the arrow of the "Flight direction" label pointed towards
the front of the aircraft.
2. Helicopters
Mount the KANNAD 406 AF COMPACT:
- with the front face connectors pointing downwards at a 45° angle to the yaw axis;
- and with "Flight direction" arrow towards the front of the helicopter.
NOTE: Should the KANNAD 406 AF COMPACT be installed on board helicopter, it will be
necessary to make a special mounting base to install the ELT.
2. DETERMINE LOCATION OF ELT
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 4
1. Drill 4 holes Ø 6 mm in the aircraft structure according to "Drilling mask" (Refer to § 2. ELT Drilling
Mask, page 502 of installation manual). Inner holes (1, 2, 3, 4) shall be preferred.
2. If the aircraft structure is not solid enough to withstand a 500 kg traction on the bracket, a
reinforcement plate (not supplied) should be installed as shown figure hereunder.
3. Fix the bracket with the 4 screws, 8 washers and 4 nylstop nuts supplied.
IMPORTANT: tighten to a torque between 4 and 5 Newton x meter.
3. INSTALL BRACKET
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 5
1. Mount the transmitter on the bracket "Flight direction" arrow pointed towards the front of the aircraft.
2. Slide the self-stripping strap throught the buckle. Ensure the buckle is correctly positioned
(indifferently on righ or left side of ELT) regarding the horizontal center line of ELT as shown
Detail A.
3. Fasten the self-stripping strap tightly.
4. INSTALL ELT
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 6
Mount the antenna out of the aircraft on the fuselage according to recommendations below.
• Locate a position on the fuselage where:
- the antenna must be installed vertically with clearance at least equal to the antenna length from
other antennas (specially VHF) mounted on the aircraft,
- when installed, the coaxial cable of the antenna will not cross any major structural sections in the
aircraft so that, in the event of a crash, the ELT and the antenna are in the same section (placing
the antenna directly above the ELT unit being the best solution)..
• A double plate will most likely be necessary for the antenna to meet rigidity specificationsin§Antenna
mounting location page 207 of installation manuel.
• Each of the approved antennas requires a ground plane. On fabric-covered aircraft or aircraft with
other types on nonmetallic skins, a ground plane must be added. This can be accomplished by
providing a number of metal foil strips in a radial position from the antenna base and secured under
the fabric or wood skin of the aircraft. The length of each foil radial should be at least equal to the
antenna length.
• A 9 Kilogram force (20 pound force) applied in all direction should not cause an appreciable distorsion
in the aircraft skin.
• According to the antenna to be installed, use the appropriate outline drawings and drilling masks to
determine the hole patern and drill size (Refer to the appropriate Outline Dimensions of installation
manuel).
• Fix the antenna to the fuselage
• Fabricate a 50 Ohms coaxial cable long enough to reach between the ELT installation location and
the antenna location.
IMPORTANT: The length of the coaxial cable should not exceed 2 meters (6 ft) for a standard
RG58 or equivalent coaxial cable. If the cable length exceeds 2 meters, a low loss cable of
attenuation less than 1 dB must be used.
• Fit both ends of coaxial cable with a waterproof Male BNC connector (not supplied), reference
RADIALL R141007.
• Connect one Male BNC connector to the antenna Female BNC socket.
5. INSTALL ANTENNA
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 7
Determine RC200 location on or below the instrument panel (be sure the location meets the
requirements established in RTCA-DO-183) in an area that is not directly exposed to sun rays.
1. On the instrument panel
- Mark a cutout on the instrument panel according to the Drilling mask (Refer to § 4. RC200 Drilling
Mask, page 504 of installation manuel).
- Make the cutout.
- Mark the 4 holes needed for the RC200 using the drilling mask or the RC200 as a guide.
- Drill the 4 marked holes, diameter depending on rivets bush used.
- Install the RC200 by fitting it into the cutout.
- Secure the RC200 (4 rivets bush recommended).
2. Below the instrument panel
- Accordingtothe"areato be drilled" (1)ofthemountingtray(3), determine thelocationofthescrews
or rivets (2) used to secure the mounting tray (3) to the instrument panel (4).
- Drill 2 holes on the mounting tray and on the instrument panel, diameter depending on screws or
rivets used.
- Secure the mounting tray (3) to the instrument panel (4).
- Secure the RC200 (5) to the mounting tray (3) with the 2 screws (6) supplied (torque 0.8 Nm).
INSTRUMENT PANEL
1
2
3
4
5
6
6. INSTALL RCP
QUICK INSTALLATION GUIDE KANNAD 406 AF-COMPACT
PAGE 8
Strap pins 4 and 5 of the female 9-pin D-SUB connector supplied with the pack.
Fabricate a 3-wire bundle (AWG 24, shielded preferred) long enough to reach between the ELT
installation location and the cockpit panel RCP location:
• Slide heat-shrinkable sleeves on both sides of each wire.
• Connect Pin 8 of D-SUB 9 to Pin G of DIN-12 connector;
• Connect Pin 4 of D-SUB 9 to Pin A of DIN-12 connector;
• Connect Pin 9 of D-SUB 9 to Pin J DIN-12 connector.
• Put heat-shrinkable sleeves to protect the pins.
• Connect the female 9-pin D-SUB connector to the male 9-pin D-SUB socket of the RC200.
1. Connect the cable of the outside antenna to the BNC connector of the front panel.
2. Connect the DIN12 connector of the Remote Control Panel cable to the DIN 12 socket of the front
panel.
3. Set the 3-position switch of the front panel to ARM.
Perform the following tests:
1. ELT operational tests: Refer to § A. ELT operational tests, page 302 of installation manual.
2. RCP operational tests: Refer to § B. RCP operational tests, page 302 of installation manual.
3. 406 & 121.5 MHz transmission tests (optional): Refer to § C. 406 and 121.5 MHz transmission test,
page 303 of installation manual.
4. At the end of this procedure, switch the ELT to ARM.
A
K
B
JLC
HM
D
G
F
E
RCP
Side
DIN-12
connector
D-SUB 9 female
connector
Connectors
view from back side of inserts
ELT
Side
3-wire bundle
(AWG 24 shielded preferred)
J1
RCP LED
5
9
3
7
2
6
1
RCP RESET 4
RCP COMMON 8
Strap
7. WIRE DIN-12 AND SUB-D 9 FEMALE CONNECTORS
8. CONNECT ELT AND SWITCH TO ARM
Otros manuales para 406 AF-COMPACT
3
Tabla de contenidos
Manuales populares de Pantalla aviónica de otras marcas
Smart Avionics
Smart Avionics PB-4 Manual de usuario
Midcontinent
Midcontinent SAM MD302 Manual
MGL Avionics
MGL Avionics Stratomaster Maxi Single FF-3 Manual de usuario
Garmin
Garmin GI 275 Manual de usuario
Mid-Continent Instruments
Mid-Continent Instruments 4300 Series Manual
Avidyne
Avidyne 700-00182 Series Manual de servicio
