KAM KML407 Manual de usuario

Party Set

KML407

Unpacking Instructions

QTY

1set

1pcs

1 pcs

1pcs

Before operating this device, please read this manual thoroughly, and retain it for future reference.

Read Manual before Operation

Please note the warnings in bold which will ensure the safe and smooth operation. These warnings are

important to a certain extent.

Attention! Indicates a skill or other useful information for special situations.

Warning Data

Carefully unpacking the carton, checking contents to ensure that all parts are in good condition. Inform the

shipper immediately and retaining packing material for inspection if any parts are damaged from shipping or

device damaged. Keeping packing materials as evidence for shippers confirmation.

Unpacking Instructions

This unit is in perfect condition before delivery, please check all accessories when unpacking the unit. User

should follow this user manual to operate this unit, and make sure that you are clear on all laser safety

information and unit operation before power it on. Any wrong operation will make this unit out of warranty.

Carefully moving after receiving it, checking whether there is any damage from shipping, and all the

accessories in it.

Attention!

Important! Indicates important information to protect personnel from laser incident or injury.

Caution! Prevent damage or injury from incorrect operation.

Warning!

Shields, lenses or ultraviolet screens should be changed if they have become visibly damaged to such an

extent that their effectiveness is impaired, for example by cracks or deep scratches.

The lamps should be changed if it has become damaged or thermally deformed.

NAME

LED system

Power Cord

User manual

Stand

Packaging bag

Safety Instructions

0.2m

◆

To protect the environment, please try to recycle the packing material as much as possible.

The KML407 is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or metallic objects.

Don't throw this product away just as general trash, please deal with the product following the abandon

electronic product regulation in your country.

Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be

fixed at least 50cm from surrounding walls.

To avoid condensation to be formed inside, allow this unit to adapt to the surrounding temperatures when bringing it

into a warm room after transport. Condensation sometimes prevents the unit from working at full performance or may

even cause damages.

Don't cover any ventilation openings as this may result in overheating.

Don't install it on flammable object.

Do not use it when maximum ambient temperature is higher than 40 degree.

Unplug the unit when it is not used for a longer time or before replacing the bulb.

Dont open the top cover to avoid unit damage.

Please use the original packing when the device is to be transported.

Never expose the lens to direct sunlight, even for a short period, this may damage the light effect or even cause fire!

Overhead Rigging &Product Installation

Adjust Angle

Attention! The installation must be carried out by qualified service personal only. Improper installation can result in

serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits

should be respected, Certified installation materials should be used, the installed device should be inspected

regularly for safety.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and

servicing.

Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be

fixed at least 50cm from surrounding walls

The device should be installed out of reach of people and outside areas where persons may walk by or be seated.

The device should be well fixed; a free swinging mounting is dangerous and may not be considered!

Do not cover any ventilation opening as this may result in overheating

Before the first time use, it must be inspected by professional staff to make sure safety, inspection regularly every

year.

Cable(EU)

Brown

Light blue

Yellow/Green

Cable(US)

Black

White

Yellow/Green

Live

Neutral

Earth

International

Please use the included power cable, note that power voltage and

frequency are the same as the marked voltage and frequency of device

when connecting power. Every devices power should be connected

separately, so that device can be controlled individually.

Cable spec.：

AC Power

L E N FUSE: 5×20mm

250V 1A slow

◆

Before rigging make sure that installation area can hold the 10 times weight of device. Using the steel rope which can

hold 12 times weight of device, through the eye-bolt for assisting hang installment.

Product Installation

Connection between lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the

attached 3 pin XLR plug/socket to connect the DMX output/input interface. The connection between socket and

cable as below( note the plug/socket’s 3 pin number and position).

Note, XLR plug/socket’s 3pin can not be touched by inner hull, connection between pins is not allowed. Except

above connection, XLR plug/socket can not be connected with XLR control line. Device receives international

standard DMX512(1990) control signal.

When using standard DMX512 control signal, the last device’s output interface must be connected to

a DMX plug. This plug is putting a 120 ohm resistance between “canon” plug’s 2 pin and 3 pin.

Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the

interference during the process of signal transmission. PIN3

PIN2

DMX-512 connection

DMX-output

XLR mounting-sockets(rear view):

DMX-input

XLR mounting-plugs(rear view):

1-Shield

2-Shield(-)

3-Shield(+)

◆

Operation instructions

23456

USA

LCD control interface

MIC

DMX input/output

Power input

Close/Auto/Sound

IR receiver

USB Type-C interface

Built-in Mic

FUNCTION DESCRIPTION

Infra-remote control receiver

Output data to external lamp socket

Various mode setting operations of the machine

Receive music signal to activate shows for the T-Bar

3PIN male/female XLR interface ,for DMX communication

AC Power input socket ,built-in fuse

Power input socket, built-in protective tube and spare tube

Par lamp power-on data input

Change the working modes of light unit between Auto,Sound and off.

7 9

Menu operating instruction

Button

ENTER

DOWN

Function

Mode / Upper menu

Confirm / Sub menu

Move up / +

Move down / -

1、The keys description:

2.Menu description

AUT

SOU

COL

AUTM

AUTP

SOUM

SOUP

COLO

R.000-R.255 Red brightness0%-100%

G.000-G.255 Green brightness0%-100%

B.000-B.255 Blue brightness0%-100%

W.000-W.255 White brightness0%-100%

A.000-A.255 Amber brightness0%-100%

AM01…AM02

Two Auto mixed shows

S.01…S.99

Show speed from slow to fast

AP01…AP18

18 Auto Par shows

S.01…S.99

Show speed from slow to fast

M.00…M.99

Show speed from slow to fast

SM01...SM02

Two Sound mixed shows

U.00…U.99

Sound sensitivity

SP01...SP18

18 Auto Par shows

U.00…U.99

Sound sensitivity

Press "ENTER"to continue

Press "ENTER"to save and display AM**

Press "ENTER"to continue

Press "ENTER"to save and display AP**

Press "ENTER"to continue

Press "ENTER"to save and display SM**

Press "ENTER"to continue

Press "ENTER"to save and display SP**

Press "ENTER"to continue

04CH( d001-d509)

07CH( d001-d506)

34CH( d001-d479)

Turn ON/OFF lights outputs

Auto mixed shows for AM01,AM02;

Sound mixed shows for SM01,SM02

Auto PAR shows for AP02,AP18

Sound PAR shows for SP02,SP18

To pause the color change effect

Auto show speed from 0-9(Slow to fast)

ON/OFF

Auto Mixed shows

Sound Mixed shows

Auto PAR shows

Sound PAR shows

Pause

Speed

Key Funntion Description

IR remote control

VALUE FUNCTION

CHANNEL

1CH

2CH

3CH

4CH

000-009

010-029

030-059

060-089

090-129

130-159

160-189

190-209

210-255

000-013

014-027

028-041

042-055

056-069

070-083

084-097

098-111

112-125

126-139

140-153

154-167

168-181

182-195

196-209

210-223

224-237

238-255

000-255

Blackout

Mix auto show 1（AN01）

Mix auto show 2（AN02）

Mix auto show 3（AN03）

Auto show 01-18（AP01-AP18）

Mix sound show 1（SN01）

Mix sound show 2（SN02）

Mix sound show 3（SN03）

Sound show 01-18（SP01-SP18）

Auto/sound program 1（AP1/SP1）

Auto/sound program 2（AP2/SP2）

Auto/sound program 3（AP3/SP3）

Auto/sound program 4（AP4/SP4）

Auto/sound program 5（AP5/SP5）

Auto/sound program 6（AP6/SP6）

Auto/sound program 7（AP7/SP7）

Auto/sound program 8（AP8/SP8）

Auto/sound program 9（AP9/SP9）

Auto/sound program 10（AP10/SP10）

Auto/sound program 11（AP11/SP11）

Auto/sound program 12（AP12/SP12）

Auto/sound program 13（AP13/SP13）

Auto/sound program 14（AP14/SP14）

Auto/sound program 15（AP15/SP15）

Auto/sound program 16（AP16/SP16）

Auto/sound program 17（AP17/SP17）

Auto/sound program 18（AP18/SP18）

Speed of auto program from slow to fast）　　　

All Dimmer

DMX-04CH mode

DMX Assignment

Tabla de contenidos

Otros manuales de Equipo de iluminación de KAM

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario