Kaba 52 Manual de usuario

52 SERIES

MODELS 52 & T52

OPERATING INSTRUCTIONS

The following instructions cover Model 52 & T52 lock operations. The lock models

operate the same except for an additional feature that is found in the Model T52 that

allows you to program a time delay for lock opening and an opening window for the lock.

After entering the proper combination(s) for the lock, the bolt cannot be retracted until the

time delay has expired. Once the delay has expired, the bolt must be retracted within the

opening window.

SUPER MASTER CONTROL

The Super Master Combination is a six-digit combination used to reset the lock to the

factory default combination (50 25 50) in the event the user combination(s) are lost. See

the Super Master Operations sheet (P/N 3001.032).

LOCK MODES

A maximum of two users can exist in a lock. A lock can operate in either Single Mode or

Dual Custody Mode.

Note: For a UL listed installation, only one user can be activated.

• Single Mode E

Single Mode defaults to having only a Manager User (User 1) in the lock. A second

user (User 2) can then be added by the Manager User (User 1). (See section on

Manager User Operations.)

In Single Mode only one valid user combination is required to open the lock - the Manager

User (User 1) combination or the User 2 combination.

Note: Default lock status from the factory is Single Mode with an opening

combination of “50 25 50” for the Manager User (User 1).

•Dual Custody Mode EE

Dual Custody Mode defaults to two users in the lock - User 1 and User 2.

Two user combinations are required to open the lock - the User 1 combination and the

User 2 combination.

Note: Manager User Operations are not available in Dual Custody Mode.

LOCK OPERATION & RESPONSES

• To “power” a self-powered lock, turn the dial back 44

4and forth 33

3in both

directions.

• The lock is “powered” when simultaneous green

and red

flashes

display with a beep 88

• Each keystroke generates a green flash

with a beep 88

• To cancel entry, press .

• The completion of a step within an operation is indicated by a green flash

with a beep 88

• The successful completion of an operation is indicated by simultaneous

green

and red

flashes. On a Battery powered lock, there will also be

a beep 88

• An error is indicated by three red flashes with beeps.

• On a Battery powered lock, a Low Battery Condition is indicated by rapidly

alternating green

and red

flashes at the time the lock is opened.

OPEN/CLOSE THE CONTAINER

1. For self-powered lock, power 44

433

3the lock

2. Position the dial to cover the red bar.

3. • For Single Mode EE

E(Factory combination is “50 25 50”.)

Enter Manager User (User 1) or User 2 combination.

• For Dual Custody Mode EE

EEE

Enter User 1 or User 2 combination.

Enter the second combination.

Wrong Try Penalty: 5 wrong tries =

3 min. lockout (Timed only while lock is powered.)

Each additional wrong try = 3 min. lockout

Red flashes with beeps

8will occur during the lockout while lock is powered.

4. • For Slide Bolt, immediately rotate the container handle to retract bolt

works before green

and red

lights flash. Open the container door. To

close and lock the container, close the door and rotate the container handle back

to locked position.

• For Dead Bolt or Spring Bolt, immediately turn the dial to the right 33

3to

retract the bolt before green

and red

lights flash and open the con-

tainer door. To close and lock the container, close the door. For Dead Bolt, you

must also turn the dial to the left 44

4until the bolt is fully extended.

CHANGE COMBINATION

WARNING: Super Master Control will be permanently lost if you do not change

the default Super Master Combination prior to changing any User combinations.

See Super Master Operations sheet (P/N 3001.032).

Caution: Before changing combination, open the container door to allow testing with the

new combination. Record new combination and store it in secure place.

1. For self-powered lock, power 44

433

3the lock

2. • For User 1 (Manager User in Single Mode)

Press . Press .

• For User 2

Press . Press . Press .

3. Enter current combination. (Factory combination is “50 25 50”.)

4. Enter new six-digit combination.

5. Enter new combination again for verification.

6. Open the lock with the new combination before closing container.

CHANGE LOCK MODE (SINGLE / DUAL CUSTODY)

Note: Changing the lock mode will reset the combination(s) to “50 25 50”.

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. • If changing from Single to Dual Custody Mode

Enter Manager User (User 1) combination.

• If changing from Dual Custody to Single Mode

Enter User 1 or User 2 combination.

Enter the second combination.

SET DELAY TIME AND OPENING WINDOW*

* This feature is only available on the Model T52 lock.

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. • For Single Mode EE

E(Factory combination is “50 25 50”.)

Enter Manager User (User 1) combination.

• For Dual Custody Mode EE

EEE

Enter User 1 or User 2 combination.

Enter the second combination.

4. Enter number of minutes (01-99) you want to delay lock opening or “00” to disable

time delay.

5. Enter delay time again for verification.

If not “00”, proceed to step 6.

6. Enter number of minutes (01-20) for the delayed opening window.

7. Enter number of minutes for the delayed opening window again for verification.

Note: A change in delayed opening will not take effect until after the next

opening of the lock.

OPENING THE LOCK WITH TIME DELAY*

* This feature is only available on the Model T52 lock.

If operating a Model T52 Lock with a Delay Time set to something other than 0, red

flashes

will display after a combination has been entered and will continue during the

delay while the lock is powered.

When the delay time expires if you are operating a self-powered lock, you must

power 43the lock. (For a battery powered lock, no powering is necessary.)

Green flashes

display with beeps 8to indicate the opening window is active

and will continue during the window while the lock is powered.

Position the dial 3to cover the red bar and then enter the combination(s) to open

the lock.

BATTERY ASSIST

When a 9 Volt Alkaline battery has been installed for Battery Assist, the LEDs will

continually flash throughout the duration of a Time Delay, Opening Window, or a Wrong

Try Lockout.

Note: The battery that is used as a power source for Battery Assist is not required for

any lock operations. There is not a battery low indicator for Battery Assist.

Manager User Operations

These operations are only available in Single Mode and can only be performed by the

Manager User (User 1). All Manager User Operations involve management of User 2.

User 2 can have a lock access status of “Enabled” or “Disabled”. If “Enabled”, User 2

can open the lock. When User 2 is added to the lock, the default lock access status is

“Enabled”. The Manager User (User 1) has the authority to change the lock access

status for User 2 and can temporarily “Disable” lock access for the user.

ADD USER 2

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. Enter Manager User (User 1) combination.

Note: User 2 is added to the lock as “Enabled” with a factory combination of “50 25 50”.

User 2 can change the User 2 combination while Enabled, but only the Manager User

(User 1) can change the lock access status.

DELETE USER 2

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. Enter Manager User (User 1) combination.

DISABLE USER 2

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. Enter Manager User (User 1) combination.

Note: If you try to disable User 2 when already disabled, you will get an error indication.

ENABLE USER 2

1. For self-powered lock, power 44

433

3the lock

2. Press . Press .

3. Enter Manager User (User 1) combination.

Note: If you try to enable User 2 when already enabled, you will get an error indication.

Battery Maintenance

The battery must be maintained for both Battery powered locks and Battery

Assist locks.

REPLACE BATTERY

1. Enter a valid combination and open the lock.

Note: For a Battery powered lock if the existing battery will not provide enough power

for you to open the lock, hold a fresh 9 Volt Alkaline Battery to the lock with the

contacts touching the metal trim encircling the red and green LEDs. The “+”

(positive) battery terminal should cover the red LED. Enter a valid combination and

open the lock while holding the battery in place.

2. Locate the battery clip mounted inside the door near the lock.

3. Note how the battery and the cable are positioned in the clip then remove the

battery and battery cable from the battery clip.

5. Unsnap the connector from the old battery and reconnect a fresh 9 Volt Alkaline

battery to the battery connector.

6. Insert the new battery and cable into the battery clip.

7. Test operation of the lock prior to closing the container.

NOTES

Kaba Mas Corporation

749 W. Short Street, Lexington, KY 40508 USA

Phone: (859) 253-4744 FAX: (859) 255-2655

Technical Support: (800) 950-4744

www.kaba-mas.com

Document Number 3002.032

Rev. C - 04/03

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Kaba

Kaba

Kaba Simplex 7104 Series Manual de usuario

Kaba

Kaba 5402 Series Manual de usuario

Kaba

Kaba SIMPLEX LD450 Manual de usuario

Kaba

Kaba E-PLEX 2000 Manual de usuario

Kaba

Kaba KEYLESS ENTRY LOCK Manual de usuario

Kaba

Kaba Simplex 1000 Series Guía de instalación

Kaba

Kaba 1546-K5 Manual de usuario

Kaba

Kaba 7102 series Manual de usuario

Kaba

Kaba Simplex Mechanical Pushbutton Locks Manual de usuario

Kaba

Kaba Simplex 1000 Series Manual de usuario

Kaba

Kaba Simplex 6200 Series Manual de usuario

Kaba

Kaba E-Plex 5x63 Manual de usuario

Kaba

Kaba Simplex 8100 Series Manual de usuario

Kaba

Kaba Simplex 506 Series Manual de usuario

Kaba

Kaba Simplex 8100 Series Manual de usuario

Kaba

Kaba Quantum Series Manual de usuario

Kaba

Kaba LA GARD 2220 Manual de usuario

Kaba

Kaba ilco 760 Instrucciones de montaje

Kaba

Kaba LA GARD COMBOGARDPRO Manual de usuario

Kaba

Kaba SIMPLEX LD470 Manual de usuario

Kaba

Kaba Gege Manual de usuario

Kaba

Kaba C-lever compact Manual de usuario

Kaba

Kaba SIMPLEX 7102 Series Manual de usuario

Kaba

Kaba 7004 Series Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario