Kaba Simplex 7104 Series Manual de usuario

7 1 0 4

SERIES

Installation Instructions

Important: Please keep these instructions. The combination of this lock has

been factory preset: 2 and 4 pressed together, then 3.

WARNING

For your own safety, you must change the combination at the time of

installation.

PLEASE READ AND FOLLOW ALL DIRECTIONS CAREFULLY

Since every installation is unique, carefully check windows, frame, door, etc. to

ensure that the recommended procedures will not cause damage. KABA is not

responsible for any damage caused by installation.

Tools Required

•1⁄4" (6 mm) Drill Bit

• 1" (25 mm) Wood Chisel

•3⁄4" (19 mm) Hole Saw

• Phillips-head Screwdriver

• 1" (25 mm) Drill Bit or Hole Saw

• 1 3⁄8" (35 mm) Hole Saw

Caution: Wear safety glasses when preparing door.

• 2 Pairs of Pliers

• Hacksaw

• Hammer

• Center Punch

• Drill (variable speed recommended)

For technical assistance please call

1-800-849-TECH (8324) or 336-725-1331

Table of Contents

Checklist .................................................................2

DeterminingtheHandofYourDoor .........................................2

A. DeterminingtheLockLocation..............................................3

B. AdjustingtheLatch(Model7014only) .......................................3

C. MarkingtheDoor..........................................................3

D. DrillingHolesintheDoor...................................................4

E. MakingtheLatchFacePlateCutout .........................................4

F. nstallingtheLatch ........................................................5

G. nstallingtheTrimPlate ....................................................6

H. AdjustingtheLock.........................................................7

. nstallingtheLock .........................................................9

J. CheckingtheLock’sOperation ..............................................9

K. nstallingtheStrike .......................................................10

L. nstructions for Resetting Unknown Combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

M. Troubleshooting ..........................................................13

Templates (Center of Manual)

CHECKLIST

Use this checklist to make sure that

everything has been included. 

A – Front lock

B–Trim Plate

C – 23⁄4" Backset Latch (7004)

–Adjustable Latch (7104)

D – nside Thumbturn Assembly

E – nside Combination Change Assembly

F – Strike Plate

Screw Pack:

G – 4 thru-bolts (3")

H – 4 combination wood/metal screws

I – 4 thru-bolts (2 3⁄8")

Template (in center of booklet)

DETER INE THE HAND OF YOUR DOOR

Many of the installation instructions refer to

the handing of your door. The hand of the

door is determined with the door in the

closed position, from the exterior or

pushbutton side of the door.

A) Right Hand Door. Door opens inward

(push). Hinged on the right side.

B) Left Hand Door. Door opens inward

(push). Hinged on the left side.

C) Right Hand Reverse Door. Door opens

outward (pull). Hinged on the right side.

D) Left Hand Reverse Door. Door opens

outward (pull). Hinged on the left side.

LH - Left Hand

RH - Right Hand

LHR - Left Hand Reverse

RHR - Right Hand Reverse

G 3"

2 3⁄8"



A. DETER INING THE LOCK LOCATION

nstall the lock with the exterior thumbturn at least

7" (18 cm) above your primary lock set so it is com-

fortable to operate and not in the way when you

turn the door knob. *A minimum stile width of

4" (10.16 cm) is required for mounting,

(See Figure 2-1).

B. ADJUSTING THE LATCH

( odel 7014 only)

This latch has been secured in the 2 3⁄4" back set

position with a spring clip. f your application

requires a 2 3⁄8" back set, remove the spring clip

by utilizing a small screw driver (or similar) and

inserting the tip through the latch as indicated by

the arrow, and gently pressing on the spring clip

until is removed from the latch.

C. ARKING THE DOOR

NOTE: Be sure to use the correct template

(right-hand or left-hand door - 2 3⁄8" or 2 3⁄4").

C-1 Carefully fold the template (found in the center

of this booklet) as indicated (See Figure 3-1).

C-2 Tape the template securely to the outside of

the door so that all the indicated folds are

properly aligned with the edge of the door.

C-3 Use a center punch to make the marks for

drilling the seven holes precisely at the points

indicated on the template. The cen-ter punch mark in the edge of the

door must be centered based on the thickness of the door.

C-4 Remove the template.

1-1

(18 cm)

*4"

2-1

Spring Clip

Adjustable Latch

3-1

D. DRILLING HOLES IN THE DOOR

CAUTION: Positioning and drilling must be done

straight to ensure troublefree operation of the

7000 Series lockset. mproper drilling may result

in excessive force being exerted on the lock which

may result in the premature wearing of its

mechanical parts.

You must do Step 1 first otherwise it will be impos-

sible to drill the 1⁄4" (6 mm) holes.

D-1 Use a 1⁄4" (6 mm) drill bit to drill the four holes

marked A (See Figure 4-1). Begin drilling at a

slow speed and increase the speed gradually until the tip of the drill bit

emerges from the other side of the door. Repeat this procedure from the

opposite side of the door. This technique will prevent splintering of the

door or breaking the drill bit.

D-2 Use a hole saw with pilot bit to make the 1 3⁄8"

(35 mm) hole. Apply pressure evenly until the

circular blade cuts the first side of the door

and the tip of the pilot bit emerges through

the other side, then stop. Drill from the other

side until the 1 3⁄8" (35 mm) hole is completed.

D-3 Repeat Step #2 for the 3⁄4" (19 mm) hole, (C).

D-4 The final 1" (25 mm) hole (D) is cross-bored

through the edge of the door. Carefully bore

4" (10 cm) deep (See Figure 4-1 and 4-2).

E. AKING THE LATCH FACE PLATE CUTOUT

This procedure is applicable to wood doors.

E-1 nsert the latch into the 1" (25 mm) hole until

the face plate butts up against the door edge.

Draw a line around the face plate, (See Figure

5-1), A. Remove the latch from the door.

E-2 For doors without a beveled edge, use a sharp

1" (25 mm) wood chisel to remove approxi-

mately 1⁄8" (3 mm) of material or enough so

the face plate is perfectly flush with the edge

of the door, (See Figure 5-1), B.

E-3 For doors with a beveled edge, follow Step 2 except the face plate will not

be flush with the edge of the door, but rather square to the face of the

door. n order to accomplish this, you must remove more wood from the

higher edge of the door.

4-2

4-1

3⁄4" (19 mm) Hole

1⁄4"(6 mm) Holes A

13⁄8" (35 mm) Hole

(25 mm)

Hole

4" (10 cm)

5-1

F. INSTALLING THE LATCH

F-1 For doors that swing outward, the curved

edge of the latch should be facing inward

towards the room. For doors that swing

inward, the curved edge of the latch should

be facing outward away from the room.

F-2 Put the latch into the 1" (25 mm) hole, (See Figure 6-1).

F-3 Secure the latch face plate to the door with the two Phillips-head screws

provided, pg.7, H.

G. INSTALLING THE TRI PLATE

G-1 Remove the two screws (A) from the back of

the lock, (See Figure 7-1).

G-2 Place the trim plate (pg.7,B) on the back of the

lock housing so that the large hole is at the

bottom. Make sure that the counter sunk sides

of the holes B are facing out, (See Figure 7-1).

G-3 Secure the trim plate to the housing with the

two screws.

H. ADJUSTING THE LOCK

The lock has been pre-assembled to accommodate

doors up to 2 1⁄4" (57 mm) thick. f your door is 1 3⁄8"

to 2" (35 mm to 51 mm) thick, you must shorten

both tailpieces X & Y (See Figure 8-1).

H-1 Shorten the combination change tailpiece X

according to your door thickness. Tailpiece X

has been premarked for various door thick-

nesses for accuracy and convenience

(See Figure 8-1).

a. After determining the breakoff point, hold

the tailpiece firmly with a pair of pliers on

the lock side of the tailpiece, just beside

the desired break line.

b. With a second pair of pliers, grip the tailpiece

at the other side of the line and bend it up

and down until it breaks (See Figure 8-2).

H-2 While holding the lockset firmly against the outside surface of the door,

(See Figure 8-1), mark tailpiece Y at the point where it extends 1⁄2-5⁄8"

beyond the interior surface of the door. Shorten tailpiece Y using the

procedure described in Steps 1a & 1b.

6-1

7-1

8-1

8-2

KABA SI PLEX®

LI ITED WARRANTY

Kaba Access Control warrants this product to be free from defects in material

and workmanship under normal use and service for a period of one (1) year.

Kaba Access Control will repair or replace, at our discretion, locks found by

Kaba Access Control analysis to be defective during this period. Our only liabili-

ty, whether in tort or in contract, under this warranty is to repair or replace

products that are returned to Kaba Access Control within the one (1) year war-

ranty period.

This warranty is in lieu of and not in addition to any other warranty or condi-

tion, express or implied, including without limitation merchantability, fitness for

purpose or absence of latent defects.

ATTENT ON: This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and /or if any supplied component part

is substituted with a foreign part. f the lock is used with a wall bumper, the

warranty is null and void. f a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes

on Kaba Access Control products. Finishes on Kaba Access Control products

are subject to change due to wear and environmental corrosion. Kaba Access

Control cannot be held responsible for the deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization Numbers (RGA Numbers) are available

through our Customer Service department in Winston-Salem, NC (800) 849-

8324. The serial number of a lock is required to obtain this RGA Number.

The issuance of an RGA does not imply that a credit or replacement will be

issued.

The RGA number must be included on the address label when material

is returned to the factory. All component parts including latches and strikes

(even if not inoperative) must be included in the package with return. All mer-

chandise must be returned prepaid and properly packaged to the address indi-

cated.

KABA ACCESS CONTROL

2941 ND ANA AVENUE

W NSTON-SALEM, NC 27199-3770

NO POSTAGE

NECESSARY

F MA LED

N THE

UN TED STATES

BUSINESS REPLY AIL

F RST-CLASS MA L PERM T NO. 1563

POSTAGE W LL BE PA D BY ADDRESSEE

W NSTON-SALEM, NC

Thank you for purchasing our product. n order to

protect your investment and to enable us to better

serve you in the future, please fill out this registration

card and return it to Kaba Access Control, or

This lock will be used in what type of facility?

Commercial Building ndustrial / Manufacturing Airport

College/University Government/Military School/Educational

Hospital/Healthcare Other (please specify)

What area is being secured with this lock? (e.g. Front Door, Common Door, Exercise Room)

This lock is:

New nstallation

Replacing a conventional keyed lock

Replacing a Kaba Mechanical Pushbutton Lock

Replacing a Kaba Electronic Access Control

Replacing a Keyless Lock other than Kaba

How did you learn about Kaba Access Control Pushbutton Locks?

Advertisement Previous Use nternet / Web Another Use

Locksmith Maintenance Training Class Other (please specify)

What was your reason for buying this lock?

Who installed your lock?

Locksmith Maintenance Other

Check here if you would like more information on Kaba Access Control locks.

Name

Position

Company

Address

City

State Z P (Postal Code) Country

Phone

Name of Dealer Purchased From

Date of Purchase

Lock Model Number

REGISTRATION CARD

Otros manuales para Simplex 7104 Series

Tabla de contenidos

Otros manuales de Cerradura de puerta de Kaba

Kaba

Kaba Ilco 790 Series Instrucciones de montaje

Kaba

Kaba E-PLEX 5X51 Manual de usuario

Kaba

Kaba Peaks Preferred Manual de usuario

Kaba

Kaba C-lever compact Manual de usuario

Kaba

Kaba Ilco 790/79 Series Manual de usuario

Kaba

Kaba Saflok RT Series Manual de usuario

Kaba

Kaba 5 00 Series Manual de usuario

Kaba

Kaba LCLX Manual de usuario

Kaba

Kaba Simplex 1000 Series Manual de usuario

Kaba

Kaba Simplex LP1000 Series Manual de usuario

Kaba

Kaba E-PLEX 3x65 Deadlatch/Exit Mortise Manual de usuario

Kaba

Kaba E-PLEX 50XX SERIES Manual de usuario

Kaba

Kaba Digital Cylinder Manual de usuario

Kaba

Kaba E-PLEX Manual de usuario

Kaba

Kaba Solitaire 710-II Series Manual de usuario

Kaba

Kaba E-Flash EF780 Manual de usuario

Kaba

Kaba C-lever Manual de usuario

Kaba

Kaba ILCO Generation E-760 Series Manual de usuario

Kaba

Kaba c-lever 2662-K5 Manual de usuario

Kaba

Kaba c-lever acc. EN1906 Cl.1 Manual de usuario

Kaba

Kaba E-PLEX STANDARD Series Manual de usuario

Kaba

Kaba S-module Manual de usuario

Kaba

Kaba EF 680E Manual de usuario

Kaba

Kaba Simplex LP1000 Series Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario