Kaba E-Plex 5900 Manual de usuario

E-Plex®5xxx Series

Egress Monitoring Installation Addendum

Kaba’s E-Plex 5900 door lock will monitor opening and closing of

the door. This is accomplished by installing a position sensor in

the door, and installing a permanent magnet in the door frame.

These are shown in the pages that follow.

Installation:

Prepare the door following the E-Plex 5x00 cylindrical lock Installation

Instructions manual. The door surface will be prepared with a 1" diameter

recessed area approximately 1" deep, which will accommodate the sensor

leads to be mounted within the door. The center of this recessed area should

be 5 1

⁄2" directly above the center of the 2 1

⁄8" hole. A hole is required for the

spindle to pass through the door 2 7

⁄16" (2.4”) above the 2 1

⁄8" hole. Refer to

the Door and Door Frame Openings illustration below.

For wooden doors, the recessed area must be deep enough to meet the wiring

path drilled within the door. Do not drill the recessed area completely through

the door. For metal doors, only drill through the outside of the door. Do not

drill completely through.

Drill a horizontal hole for the sensor and wires through the edge of the door

to intersect with the recessed area 5 1

⁄2" above the latch. The horizontal hole

size is 3

⁄8" inch diameter and 1" deep for a tight t with the sensor. The

remainder should be a 1

⁄4" diameter wire path above or below the upper lock

mounting holes.

Caution: Make sure that the drill path does not interfere with the two upper

⁄4" lock mounting holes.

Outside lock mounting

surface of door.

6.0"

Sensor

Hole 5.5"

Recessed

Hole

5.4"

Mounting

Hole

2.4"

Spindle

Hole

Wire passage holes intersect,

avoiding two mounting holes.

Align magnet in door frame

with sensor in door.

Wood: .250" dia hole, .375" deep.

Steel: .295" dia hole for

mounting collar.

1" dia recessed

1" deep for wire junction

Pass through hole for small

spindle.

Latch

Door Frame

Ensure that no part of the

wires are pinched or shorted

during installation. Place

excess wire in the door, and

nish installing the lock ac-

cording to the instructions in

the manual adding the spindle

connecting both sides accord-

ing to the Spindle Installation

illustration at the right.

Locate the position for the

sensor magnet. Align the

magnet with the sensor now

mounted in the door edge.

In wood, drill a 1

⁄4" hole to be

3/8" deep for the magnet. In

steel, use a size M (.295") drill

and mount the magnet with

the collar provided.

Caution: The magnet is

strong. Avoid placing the

magnet near sensitive devices

such as magnetic stripe cards.

Route the wires through the door.

It is important to ensure that each

wire from the sensor is connected

to a wire extending from the lock

housing. Polarity is not required.

Insulate the junctions. Refer to the

Wire Connections at the left.

Egress Sensor

and Wire

Sensor

Wires in Lock

Outside

Lock

1. Push spindle into mating

socket of the outside hous-

ing until it ”snaps“ into place.

Rotate the spindle to have

the sharp edges horizontal.

2. Place socket

onto spindle.

The socket

has the sharp

corners

horizontal.

Kaba Access Control

2941 Indiana Avenue

Winston-Salem, NC 27105 USA

Tel: (800) 849-8324 (336) 725-1331

Fax: (800) 346-9640 (336) 725-3269

For Technical Assistance

Tel: 1-800-849-TECH (336) 725-1331

www.kabaaccess.com

PKG3235 0308

Otros manuales para E-Plex 5900

Este manual sirve para los siguientes modelos

Otros manuales de Cerradura de puerta de Kaba

Kaba

Kaba EF 680E Manual de usuario

Kaba

Kaba Ilco 790/79 Series Manual de usuario

Kaba

Kaba Peaks Preferred Manual de usuario

Kaba

Kaba Combi B 30 Manual de usuario

Kaba

Kaba E-Plex 5X10 Manual de usuario

Kaba

Kaba SIMPLEX 3000 NARROW STILE Manual de usuario

Kaba

Kaba 5 00 Series Manual de usuario

Kaba

Kaba E-Plex 5900 Manual de usuario

Kaba

Kaba Simplex 1000 Series Guía de instalación

Kaba

Kaba E-Plex 5200 Manual de usuario

Kaba

Kaba C-lever compact Manual de usuario

Kaba

Kaba Saflok RT Series Manual de usuario

Kaba

Kaba 7102 series Manual de usuario

Kaba

Kaba E-Flash EF780 Manual de usuario

Kaba

Kaba E-PLEX 5X51 Manual de usuario

Kaba

Kaba E-PLEX 50XX SERIES Manual de usuario

Kaba

Kaba E30 Manual de usuario

Kaba

Kaba LCLX Manual de usuario

Kaba

Kaba C-lever Manual de usuario

Kaba

Kaba Digital Cylinder Manual de usuario

Kaba

Kaba E-PLEX Manual de usuario

Kaba

Kaba c-lever acc. EN1906 Cl.1 Manual de usuario

Kaba

Kaba Saflok MT RFID Manual de usuario

Kaba

Kaba SIMPLEX 900 Series Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario