K2 Pumps ASP00001K Manual de usuario

Model: ASP00001K

OWNER’S MANUAL

Backup Sump Pump

Questions, problems, missing parts? Before returning to the store call

K2 Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday

1-844-242-2475

www.K2pumps.com

2 For Professional Technical Support call 1-844-242-2475

PERFORMANCE

Model

Inlet water

pressure

GPH of Water @ Total Feet Of Lift

0 ft.

5 ft.

10 ft.

15 ft.

ASP00001K

40PSI

573

495

420

340

60PSI

702

630

545

465

SAFETY INSTRUCTIONS

1. Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not use in the

presence of flammable or explosive vapors. Using this pump with or near flammable liquids can cause an explosion

or fire, resulting in property damage, serious personal injury, and/or death.

2. Disconnect power (unplug) the primary sump pump before installing, working on, or servicing the backup sump

pump.

3. The backup sump pump requires a city water source with a minimum pressure of 40PSI. The inlet pipe should be at

least 3/4” in diameter.

4. Clean the backup sump pump regularly.

5. Release all pressure and drain all water from the system before servicing any component.

6. Secure the discharge line before starting the pump. An unsecured discharge line will whip, possibly causing

personal injury, and/or property damage.

7. Wear safety goggles at all times when working with pumps.

8. Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO

USE A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.

9. Know the pump and its applications, limitations, and potential hazards.

10. Periodically inspect the pump and system components to ensure the pump suction screen is free of mud, sand, and

debris

11. Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all

Occupational Safety and Health Administration (OSHA) guidelines must be followed.

PRE-INSTALLATION

APPLICATION

The backup sump pump is designed for as an auxiliary back-up sump pump for private residences in case of

primary sump pump failure or a power outage. It is not designed for and should not be used as a primary sump

pump.

TOOLS REQUIRED

For Professional Technical Support call 1-844-242-2475 3

MATERIALS REQUIRED (NOT INCLUDED)

NOTE: Parts shown below not to scale.

SPECIFICATIONS

Liquid temp. range

32 to 95°F (0- 35°C)

INSTALLATION

1. NOTE: Install the emergency sump pump when the primary sump

pump isn’t needed. Read the instruction and prepare all suppliers

before starting.

Verify that the existing primary sump pump is in good working

order. If the primary pump is questionable, replace with the same

or a higher HP pump. The primary pump is better to have a

vertical float switch or electrical switch. Tethered float switch

takes more sump pit space and might interfere with the

emergency pump.

Manually operate your primary sump pump and pump out the

water in your sump pit. Do not let the pump run dry. This will

damage the pump.

Disconnect the primary sump pump power source before

attempting to install. Never handle a pump with wet hands or

when standing on wet or damp surface or in water. Fatal

electrical shock could occur.

Remove any silt or accumulated debris from the sump pit and surrounding area.

Close the inlet valve of the city water and open the tap to discharge water.Cut the city water pipe at a

proper position.

4 For Professional Technical Support call 1-844-242-2475

2. Install a Y pipe in the primary sump pump discharge

pipe.

If necessary adjust the PVC pipe length so that nothing

interferes with the primary pump and switches.

3. Install a check valve in the emergency pump

discharge. Install the pipe on the check valve.

4. Connect the emergency pump discharge pipe to the Y

shape pipe.

Note: Adjust the height for the emergency pump and

keep 2”-4” to the bottom.

5. Install a Tee pipe in the system. One end connects to

the tap and another end connects to the emergency

pump.

Ensure that the pipe around 5" in diameter.

Use clamp to fix city water inlet pipe and discharge

pipe.

For Professional Technical Support call 1-844-242-2475 5

6. Open the city water inlet valve to clean the pipe

assembled. After that close the inlet valve.

7. Install the control valve to the tap water pipe , ensure

the pump and float switch keep nonintervention.

8. Connect the hose to the inlet and lock with clamp.

9. Connect the float rods with connection nuts. After

connecting the 3 float rods, fix metal ring at the

connection nuts.

6 For Professional Technical Support call 1-844-242-2475

Dimension

Complete Installation

For Professional Technical Support call 1-844-242-2475 7

OPERATION

1. Plug the pump plug into piggyback plug and

then plug it to GFCI plug, open the main valve.

2. Pour water and test if the emergency pump can work

normally.

Verify primary pump operation. Fill the sump pit with

enough water. The primary sump pump will start and

pump out the water then stop.

Unplug the primary pump power cord plug from the power

supplier outlet.

Verify emergency pump operation. Refill the sump pit

with water until the emergency pump float switch moves

to the upper end. The emergency pump should start and

pump out the water. If not, please check all the pipe

connections and adjust the position of the 2 rubber rings

on the float rod.

3. Plug the primary sump pump after testing and be sure the power supply is on.

8 For Professional Technical Support call 1-844-242-2475

CARE AND CLEANING

1. Turn off the tap water valve and loosen the clamp. And

then pull out the hose.

2. Clamp the inlet hose of backup pump with channel

Locks and then pull out the backup pump.

3. Loosen the screw and remove the bottom board, clean the nozzle and venturi with 3/16” Dowel. Re-install after

cleaning

For Professional Technical Support call 1-844-242-2475 9

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

No water is pumped

1. No supply water

2. Automatic Valve doesn’t open

3. Float sunk or stuck

4. Ejector is plugged

5. Inlet screen is plugged

6. Water level has dropped below inlet

screen level

7. Primary sump pump check

8. Discharge line plugged

9. Pump is trying to exceed rated lift

10. Water supply is below 40 PSI

11. Water Supply is a well system

1. Open supply valve

2. Check valve operation manually,

replace valve

3. Check float for free action,

obstructions

4. Clean ejector

5. Clean inlet screen

6. Adjust the float rod stops to shut

off pump before water has

dropped below screen level.

7. Install or clean check valve in

primary pump discharge

8. Inspect and clean all pipes in

system

9. Reduce height of discharge (see

“Performance Chart”page 2). DO

NOT try to exceed lift heights

shown

10. Install a larger pipe (3/4”or 1”)

from city water supply

11. Pump requires continuous

pressure to operate - it will not

operate if supply is from a well

pump

Pump operates at less than full

capacity

1. Supply water flow is restricted

2. Pump suction or pump’s ejector

partially plugged

3. No primary pump check valve

4. Primary pump’s check valve leaks

5. Discharge line partly plugged

1. Open supply valve completely,

make sure automatic valve is fully

open and operating correctly

2. Clean as needed

3. Install a check valve in primary

pump’s discharge

4. Replace primary pump’s check

valve

5. Clean out pipe

Pump operates continuously

doesn’t shut off.

1. Automatic valve sticking open

2. Float is stuck in “ON” position

3. Rod stops are incorrectly set

1. Manually check operation of

automatic valve

2. Clear obstructions

3. Adjust position of rod stops on the

float rod to allow correct valve

operation.

10 For Professional Technical Support call 1-844-242-2475

WARRANTY

Limited Warranty

WHAT THIS WARRANTY COVERS

When used and maintained in normal use and in accordance with the Owner’s Manual, your K2 product is warranted

against original defects in material and workmanship for at least one year (warranty varies depending on model; see box

for specific warranty information) from the date of purchase (the “Warranty Period”). During the Warranty Period, K2 will

repair or replace at no cost to you, to correct any such defect in products founds upon examination by K2 to be defective

in materials or workmanship.

Your dated receipt of purchase is required to make a warranty claim.

WHAT THIS WARRANTY DOES NOT COVER

This Warranty does not cover:

Use of the product in a non-residential application, improper installation and/or maintenance of the product, damage due

to misuse, acts of God, nature vandalism or other acts beyond control of K2, owner’s acts or omissions, use outside the

country in which the product was initially purchased and resale of the product by the original owner. This warranty does

not cover pick up, delivery, transportation or house calls. However, if you mail your product to a K2 Sales and Service

Center for warranty service, cost of shipping will be paid one way. This warranty does not apply to products purchased

outside of the United States, including its territories and possessions, outside of U.S. Military Exchange and outside of

Canada. This warranty does not cover products purchased from a party that is not an authorized retailer, dealer or

distributor of K2 products.

OTHER IMPORTANT TERMS

This warranty is not transferable and may not be assigned. This Warranty shall be governed and construed under laws

of the state of Michigan. The Warranty Period will not be extended by any replacement or repair performed under this

Warranty. THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY K2. ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR

PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL K2 BE LIABLE FOR ANY SPECIAL, INDRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY

CLAIMING THROUGH OWNER WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT, OR STRICT PRODUCTS

LIABLITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow for the exclusion of

consequential damages, so the above exclusion may not apply to you. This warranty gives you specific rights. You may

also have others that vary from state to state.

Thank you for choosing a K2 product!

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de agua de K2 Pumps

K2 Pumps

K2 Pumps UTM02501K Manual de usuario

K2 Pumps

K2 Pumps UTS03301K Manual de usuario

K2 Pumps

K2 Pumps UTM01602K Manual de usuario

K2 Pumps

K2 Pumps WPS05001K Manual de usuario

K2 Pumps

K2 Pumps SPP05001K Manual de usuario

K2 Pumps

K2 Pumps WPS05004K Manual de usuario

K2 Pumps

K2 Pumps Contractor Series Manual de usuario

K2 Pumps

K2 Pumps SPI05008TPK Manual de usuario

K2 Pumps

K2 Pumps Primary Series Manual de usuario

K2 Pumps

K2 Pumps UTM02501K Manual de usuario

K2 Pumps

K2 Pumps IRP07501K Manual de usuario

K2 Pumps

K2 Pumps WPS05003K Manual de usuario

K2 Pumps

K2 Pumps SPI03303TPK Manual de usuario

K2 Pumps

K2 Pumps Contractor Series Manual de usuario

K2 Pumps

K2 Pumps SPA02501VDK Manual de usuario

K2 Pumps

K2 Pumps SPI03302K Manual de usuario

K2 Pumps

K2 Pumps WPD07502K Manual de usuario

K2 Pumps

K2 Pumps UTT01003K Manual de usuario

K2 Pumps

K2 Pumps UTA02502K Manual de usuario

K2 Pumps

K2 Pumps SPP03301K Manual de usuario

K2 Pumps

K2 Pumps UTA02505APK Manual de usuario

K2 Pumps

K2 Pumps UTA02502APK Manual de usuario

K2 Pumps

K2 Pumps WPS05002K Manual de usuario

K2 Pumps

K2 Pumps WPS07505PCK Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario