K-Tech ET401A Manual de usuario
K-Phone ET401
Emergency Speakerphone
Instruction Book
Sentry(ET401A)
Fortress (ET1401A)
Commander (ET401A-OEM)
Liberator (ET401A-LP)
Please read carefully before
installation and operation
Page 2
Page 3
Table of Contents
Introduction
................................................................................... 4
Pre-Installation Checklist
.............................................................. 5
Wiring
........................................................................................... 5
Telephone Lines
........................................................................... 5
Telephone Line Specifications
....................................................... 5
Wiring Diagram
............................................................................. 6
Installation
.................................................................................... 7
Sentry (ET401A)
........................................................................... 7
Liberator (ET401A-LP)
.................................................................. 8
Fortress (ET1401A)
...................................................................... 9
Commander (ET401A-OEM)
....................................................... 10
Settings
...................................................................................... 11
Programming
.............................................................................. 12
Operation and
Testing................................................................. 16
Troubleshooting
.......................................................................... 17
Specifications
.............................................................................. 18
Code Compliance
....................................................................... 19
FCC Notice for Part 68
................................................................ 20
FCC Notice for Part 15
................................................................ 21
IC Notice
..................................................................................... 22
Service & Warranty Agreement
................................................... 23
For Technical Support call
1-800-993-9399 or (860) 489-9399
Page 4
Introduction
Thank you for purchasing the K-Tech K-Phone ET401 Emergency
Speakerphone. This vandal resistant speakerphone is designed to
provide reliable communication in the event of an emergency. Each
unit features a tone dialer capable of dialing five twenty-digit
numbers, a voice activated location announcer with 10 second
message, and remote, on-site, and off-site programming
capabilities. All programming features are stored in non-volatile
memory.
The K-Phone ET401 activates with a single press of the push-
button, which initiates automatic dialing of the programmed
emergency telephone number(s) until a called party answers. The
voice activated Voice Announcement replays the recorded
message, after which two-way communication begins or the
message can be replayed. The visual indicator illuminates to
indicate the unit is activated; this light can be made to flash by the
called party to indicate that help is on the way.
When the call is completed, the phone will shut off automatically, or
can be remotely shut off. The K-Phone ET401 can be called back to
establish two-way communication from any telephone at any time.
K-Phone ET401 Emergency Speakerphones are available in four
different mounting styles. See pages 7 - 10 for more detailed
information.
Sentry (ET401A) - surface or phone box mount
Fortress (ET1401A) - flush mount
Commander (ET401A-OEM) - operating panel mount
Liberator (ET401A-LP) - surface or phone box mount
Pre-Installation Checklist
q
Read this manual completely before installation.
q
Check that you have a live telephone line (24 or 48 VDC, CO or
PBX) installed and terminated at the elevator machine room.
Tools Required:
qsmall flathead screwdriver
q1/4” nut-driver
qwire cutters
qlong-nosed pliers
qdrill and pilot bit for #8 sheet metal screw
qDigital Multimeter (DMM)
q9 volt battery (for programming)
Page 5
Wiring
We strongly recommend that the wires used to supply the telephone
line to K-Tech emergency speakerphones be 20 AWG shielded,
twisted pair.
The shield must be continuous from the speakerphone through the
traveling cable to the incoming telephone line termination. Make
sure the shield is connected to a
true earth ground at one end
only!
This will minimize the interference from AC inductance and RF
(radio frequency).
Telephone Lines
For best operation, each K-Tech K-Phone ET401 Emergency
Speakerphone must be installed on an analog touch-tone telephone
line. Compatible line types are standard analog two-wire central
office lines (POTS) from the local telephone company or most
internal PBX systems.
The K-Phone ET401 Emergency Speakerphone should be
installed on a dedicated telephone line. Sharing a telephone line
with other devices (e.g. fax machine, alarm system, another
telephone, etc.) could affect code compliance and/or cause the
K-Phone ET401 Emergency Speakerphone to malfunction.
The telephone line will be assigned a telephone number which
allows the called party to call back to the location of the emergency.
Take care to note this number and supply it to the called party.
Telephone Line Specifications
Line Type Standard two-wire voice analog
Line Voltage 24 VDC minimum on-hook
Loop Current 30 mA minimum
Page 6
Wiring Diagram
Connect
Telephone
Line shield to
true earth
ground at
one end
only!
TELEPHONE LINE
MICROPHONE
SPEAKER
Increase
VOL.
9
6
3
#*
1
4
7
2
5
8
0
BUT
LED
+
-
9.0 VDC IN
REMOTE
LED
2V 7mA
PHONE
LINE
R
T
REMOTE
BUTTON
Dry
Contacts
12 - 30V
ONLINE
PROG
AUX
POWER
RINGS
5 -
7 -
9 -
K-Tech International Inc.
Part # PCB009 Rev D.
SERIAL #
Page 7
Installation
Sentry (ET401A)
1.
Use the 3/32” Allen wrench (included) to unscrew the fasteners
and remove the rear enclosure.
2.
Using the rear enclosure as a template, mark the mounting
screw hole locations.
3.
Drill holes for two #8 screws (included).
4.
Mount the rear enclosure placing the Ground Lug under one of
these mounting screws.
WHEN LIGHT
FLASHES
HELP IS ON
THE WAY
K-Tech International, Inc, Torrington, CT
5.
Proceed to Settings on page 11.
6.
Proceed to Programming on page 12.
7.
Proceed to Operation and Testing on page 16.
Page 8
Liberator (ET401A-LP)
1.
Use the 3/32” Allen wrench (included) to unscrew the fasteners
and remove the rear enclosure.
2.
Using the rear enclosure as a template, mark the mounting
screw hole locations.
3.
Drill holes for two #8 screws (included).
4.
Mount the rear enclosure placing the Ground Lug under one of
these mounting screws.
WHEN LIGHT FLASHES
HELP IS ON THE WAY
K-Tech International, Inc, Torrington, CT
5.
Proceed to Settings on page 11.
6.
Proceed to Programming on page 12.
7.
Proceed to Operation and Testing on page 16.
Page 9
Fortress (ET1401A)
1.
Determine the mounting location and cut a 10” x 7” (25 cm x 18
cm) opening to allow for the back enclosure.
2.
Using the faceplate as a template, mark the mounting screw
hole locations.
3.
Drill holes for four #8 security screws (included).
K-Tech International, Inc, Torrington, CT
WHEN LIGHT FLASHES
HELP IS ON THE WAY
4.
Remove the enclosure by removing the two nuts that secure it.
5.
Proceed to Settings on page 11.
6.
Proceed to Programming on page 12.
7.
Remount the enclosure, placing the Ground Lug under one of
the nuts that secure it.
8.
Mount the unit over the opening using the #8 security screws
(included).
9.
Proceed to Operation and Testing on page 16.
Page 10
Commander (ET401A-OEM)
1.
Using the faceplate as a template, align the microphone and
speaker with the grill pattern; mark and install the mounting
studs.
2.
Mount the faceplate tightly against the back of the COP to avoid
feedback between the microphone and speaker.
MICROPHONE
SPEAKER
Increase
VOL.
9
6
3
#*
1
4
7
2
5
8
0
BUT
LED
+
-
9.0 VDC IN
REMOTE
LED
2V 7mA
PHONE
LINE
R
T
REMOTE
BUTTON
Dry
Contacts
9-24V
ONLINE
PROG
AUX
POWER
RINGS
5 -
7 -
9 -
K-Tech International Inc.
Part # PCB009 Rev D.
SERIAL #
3.
Connect the normally open (NO) contacts of the push-button to
the terminal labeled REMOTE BUTTON (see Wiring Diagram on
page 6).
4.
Connect the visual indicator to the terminals labeled REMOTE
LED taking care to follow the correct polarity.
5.
Proceed to Settings on page 11.
6.
Proceed to Programming on page 12.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Teléfono de K-Tech
