Jung BM360MBWW Manual de usuario

Motion detector mini basic

Art. no.: BM360MBWW

Motion detector mini basic

Art. no.: BM360MBWW-270

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. During installation and cable routing, comply with the regulations and

standards which apply for SELV circuits.

Do not press on the sensor window. Device can be damaged.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end customer.

2 Intended use

Intended use

– Brightness-independent detection of motion indoors.

– Connection to the KNX devices mentioned under accessories e.g. Multistation or push

button interface for the automatic switching of loads.

– Power supply via the unchoked output of a KNX power supply or power supply unit with

safety extra-low voltage (SELV).

– Clamp mounting in suspended ceilings.

– Ceiling mounting on fixed ceilings in appliance box according to DIN 49073 or surface-

mounted housing (see accessories)

3 Function

– Brightness-independent detection of motions in the detection field

– Switch on: After detecting motion

– Switch off: No motion in the detection field and run-on-time elapsed

– Potential-free electronic switching contact

4 Information for electrically skilled persons

4.1 Fitting and electrical connection

Selecting installation location

The motion detector is installed on the ceiling and monitors the surface under it.

￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.

￭ Avoid interference sources in the detection area. Interference sources, e.g. heaters, vent-

ilation, air conditioners, and cooling light bulbs can lead to unwanted detections.

If necessary, the detection field can be limited using the push-on cover in order to minim-

ize the influence of interference sources.

1 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

Motion detection

Figure1: Tangential and radial direction of motion

The device has a detection field of 360°. The diameter of the detection field depends on the in-

stallation height and the direction of motion of persons in the detection field (Figure 1). The de-

tection field becomes larger the greater the installation height, while the detection density and

sensitivity are reduced at the same time. The following applies to an installation height of 3 m:

1: Range for tangential motion on the ground Ø approx. 6 m

2: Range for radial motion on the ground Ø approx. 5.5 m

DANGER!

Electrical shock on contact with live parts in the installation environment.

Electrical shocks can be fatal.

Before working on the device, disconnect the power supply and cover up live parts

in the working environment.

Create a mounting opening in the suspended ceiling

Figure2: Mounting in the suspended ceiling

(1) Spring clamp

(2) Cable fixation

2 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

(3) Terminal

(4) Motion detector

(5) Design ring

The environment in the suspended ceiling must be dry.

Max. thickness of the suspended ceiling approx. 25 mm. Installation depth min. 35 mm. Dis-

tance between concrete ceiling and suspended ceiling min. 20 mm (Figure 2).

￭ Create ceiling cut-out Ø 44...45 mm(Figure 2).

Connecting the device

Figure3: Clampable conductor cross-section

Recommended line J-Y(St)Y 2×2×0.8 (2 wire pairs, conductor diameter 0.8 mm this corres-

ponds to a conductor cross-section of 0.5 mm²).

For the cable length, also observe the information in the instructions for the device to be con-

nected.

￭ Use the unchoked output of a KNX power supply or power supply unit with safety extra-

low voltage as power supply.

￭ Connect the connection cable to device connection terminal (3) (Figure 2).

Connection in general

Terminal assignment of motion detector

Terminal Connection

DC24V + Power supply +

DC24V – Power supply GND

Switching output

Figure4: Connection in general

For connection diagrams for various KNX devices, see accessories

Figure5: Connection to Multi station, Rotary sensor

3 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

Figure6: Connection to Binary input 6-gang

Figure7: Connection to Binary input 8-gang, 24 V

Figure8: Connection to Push-button interface, 2-gang, Push-button interface, 4-gang

Figure9: Connection to flush-mounted actuators: Switch actuator, 2-gang / blinds actuator, 1-

gang, Switch actuator, 1-gang, Universal dimming actuator, 1-gang

Figure10: Connection to Room temperature controller with push-button interface 4-gang, Room

autostat with push-button interface 4-gang, CO2 multi-sensor

4 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

Figure11: Connection to Valve drive (motor-operated) with controller

Figure12: Connection to KNX Push-button universal

(Figure 4) (6) Motion detector mini basic

(Figure 5) (7) Multi station, Art. no.: 23066REGHE, Rotary sensor, Art. NoD-

S4092TS.:

(Figure 6) (8) Binary input 6-gang, Art. no.: 2116REG

(Figure 7) (9) Binary input 8-gang, 24 V, Art. no.: 2128REG

(Figure 8) (10) Push-button interface, 2-gang, Art. no.: 2076-2T, Push-button

interface, 4-gang, Art. No2076-4T.:

(Figure 9) (11) Switch actuator, 2-gang / blinds actuator, 1-gang, Art. no.:

230021SU, Switch actuator, 1-gang, Art. no.: 230011SU, Univer-

sal dimming actuator, 1-gang, Art.no.: 390011SU

(Figure 10) (12) Room temperature controller with push-button interface 4-

gang, Art. no.: ..2178TS, Room autostat with push-button interface

4-gang, Art. no.: ..2178 ORTS.., CO2 multi-sensor, Art.no.:

CO2..2178..

(Figure 11) (13) Valve drive (motor-operated) with controller, Art. no.:

2177SVR

(Figure 12) (14) KNX Push-button universal, Art. no.: ..109.1ST

Mounting the device in the suspended ceiling

￭ Secure the connection cable with the enclosed cable fixation (2) (Figure 2).

￭ Bend back the spring clamps (1) and push the motion detector (4) into the suspended

ceiling (Figure 2).

￭ Attach the large design ring (5) and rotate it in clockwise direction (Figure 2).

5 Technical data

Rated voltage DC 24 ... 32 V SELV

Standby power max. 0.1 W

Current consumption max. 4 mA

Ambient temperature -5 ... +45 °C

Storage/transport temperature -25 ... +70 °C

Relative humidity 10 ... 100 % (no moisture condensation)

Protectionclass III

5 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

Degree of protection IP44

Detection angle 360°

Installation height 3 m

Detection field Ø approx. 6 m

Run-on time

BM360MBWW approx. 10 s

BM360MBWW-270 approx. 270 s

Switching output

Electric strength 40 V

Current carrying capacity max. 50 mA

Connected load max. 150 mW

Dimensions

Dimensions Ø×H 53.5 × 38 mm (with design ring)

Ceiling cut-out Ø×D 44 × 35 mm

Cable length max. 30 m

6 Accessories

Power supply 160 mA Art.-no.: 20160REG

Power supply 320 mA Art.-no.: 20320REG

Power supply 640 mA Art.-no.: 20640REG

Power supply 1280 mA Art.-no.: 21280REG

Multi station Art.-no.: 23066REGHE

Binary input 6-gang Art.-no.: 2116REG

Binary input 8-gang, 24 V Art.-no.: 2128REG

Push-button interface, 2/4-gang Art.-no.: 2076-..T

Switch actuator, 1-gang Art.-no.: 230011SU

Universal dimming actuator, 1-gang Art.-no.: 390011SU

Switch actuator, 2-gang / blinds actuator, 1-

gang

Art.-no.: 230021SU

Room temperature controller with push-button

interface 4-gang

Art.-no.: ..2178TS

Room autostat with push-button interface 4-

gang

Art.-no.: ..2178 ORTS..

CO2 multi-sensor Art.-no.: CO2..2178..

Rotary sensor Art.-no.: DS4092TS

KNX Push-button universal Art.-no.: ..109.1ST

Valve drive (motor-operated) with controller Art.-no.: 2177SVR

Flush mounting set Art.-no.: PMM-UP-SET-WW

Surface mounting set Art.-no.: PMM-AP-SET-WW

7 Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.

6 / 7

82403113 17.11.2021

J0082403113

Motion detector mini basic

ALBRECHT JUNG GMBH & CO. KG

Volmestraße 1

58579 Schalksmühle

GERMANY

Telefon: +49 2355 806-0

Telefax: +49 2355 806-204

[email protected]

www.jung.de

7 / 7

82403113 17.11.2021

J0082403113

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de Jung

Jung

Jung HOME BT 17181 Series Manual de usuario

Jung

Jung BM 240 S1A WW Manual de usuario

Jung

Jung Radio Detector 180 Manual de usuario

Jung

Jung DWPM17360AL Manual de usuario

Jung

Jung Observer 70 Manual de usuario

Jung

Jung PMU 360 WW Manual de usuario

Jung

Jung Observer 110 Manual de usuario

Jung

Jung KNX 3361MWW-01 Manual de usuario

Jung

Jung 17180 Series Manual de usuario

Jung

Jung Observer 220 Manual de usuario

Jung

Jung FM ES 36804 REG Manual de usuario

Jung

Jung 3361MWW Manual de usuario

Jung

Jung 3360 Manual de usuario

Jung

Jung BT17361 Series Manual de usuario

Jung

Jung FMDW360WW Manual de usuario

Jung

Jung 3361WW-01 Manual de usuario

Jung

Jung PMK 360 WW Manual de usuario

Jung

Jung DWPMK360WW Manual de usuario

Jung

Jung Standard 3361 WW Manual de usuario

Jung

Jung FPM360WW Manual de usuario

Jung

Jung BT 17182 Series Manual de usuario

Jung

Jung Mini basic Manual de usuario

Jung

Jung 2103 REG ES Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario