Joto E-HP-JMP-1S7E Manual de usuario
Single Station
Includes 7 elements
Joto Digital Mug Press Manual -
Single Station includes 7 Elements
Model No.: E-HP-JMP-1S7E
OPERATOR’S MANUAL
2www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Safety Instructions
For Use By Qualied Personnel Only
When using your Mug Press,
basic precautions should always be followed,
including the following:
Read all instructions.
Use mug press only for its intended use.
Always keep the mug press dry. Do not get the mug press wet to reduce the risk of electric shock.
Avoid storing mug press in a wet/ damp area.
Never pull the cord to disconnect the power. Instead, grasp plug and pull to disconnect from power
outlet.
Make sure you protect the power cord by keeping it away from hot surfaces. Avoid placing objects
on top of the cord. This could cause damage to the cord and could be a re hazard risk.
Do not operate mug press with a damaged cord or if the equipment has been damaged. To prevent
risks of injury, please do not disassemble or attempt to repair the mug press by yourself if you are
not qualify to do so. Instead, call or take it to a qualied service person for examination and repair.
Incorrect assembly or repair could increase the risk of re, electric shock, or injury to persons when
the equipment is used.
If mug press being used by or near children, please make sure that it is supervised. Do not leave
equipment unattended while connected.
Metal parts on the press can become hot. Avoid touching the hot metal parts to prevent burns.
Proceed with caution when using the mug press.
To reduce the likelihood of circuit overload, Joto recommends to use a dedicated circuit if possible.
Make sure that the cord is safely secured so it cannot be pulled or tripped over.
If you need to use an extension cord, make sure you use a 20 amperage rated cord. Cords rated
below 20 amperage can overheat. Make sure that the extension cord is safely secured so it cannot
be pulled or tripped over.
Note: Temperature is in Fahrenheit or Celsius. This mug press should not be set to exceed
400˚F (200˚C). Setting the press temperature to above 400˚F (200˚C) will burn out your mug
element and may cause a re hazard.
Do not use any other power cords other than the one provided with this machine. Doing so may
result in a re hazard. If you need a replacement cord, please call Joto at 1-800-565-5686 to
request one.
PLEASE KEEP THE BOX THAT YOUR MUG PRESS ARRIVED IN,
ALONG WITH ALL ORIGINAL PACKAGING.
3
www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Congratulations on your purchase of a Joto Single Station Mug Press with 7 elements! In order
to work professionally with the machine and start production, please make sure you read this
manual carefully.
Reproduction of this manual requires written consent from Joto. Errors and amendments
of technical details excepted, all rights reserved. Joto is not liable for any direct or indirect
damages caused by the use of this product.
Table of Contents
Safety........................................................2
Introduction .............................................3
Mug Press Overview ..............................4-5
Machine Parts Diagram ............................6
Setting Up Your Mug Press .......................7
Elements Overview ...................................8
Operating Instructions .............................9
Replacing The Mug Element ...................10
Joto Sublimation Guide ..........................11
Maintenance ...........................................11
Expanded View ................................. 12-13
Circuit Diagram .......................................14
Warranty .................................................15
Contact Information ...............................16
4www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Mug Press Overview
Technical Specs
Model No.: E-HP-JMP-1S7E
Machine Type: Single Station Mug Press with 7 Elements
Machine Size: 23.62” x 16.85” x 11.69”
(604 x 428 x 297mm)
Printable Articles Max Size: 6” x 4”
Mug Heater Size: 11oz/15oz Mug, Dia. 6-7.5cm for 6oz, 9oz, 10oz etc
Mug, Dia. 5-9cm for 11oz, 15oz etc Mug, Tumbler
(up to ~8.5" tall), 12oz/17oz Latte ,1.5oz Shot,
2.5oz Expresso Shot
Voltage: 220V/1Phase; 110V/1Phase
Power: 130W, 0.59A
Recommended Settings: 30~280s; 356~400°F (180~200°C)
Time Range: 0~999s
Maximum Temp: 437˚F (225˚C)
Packing Size: 18.70" x 13.97"x 12.20" (47.5 x 35.5 x 31cm)
Gross Weight: 21.38lbs (9.70kg)
Note: Temperature is in Fahrenheit or Celsius. This mug press should not be set to exceed 400˚F
(200˚C). Setting the press temperature to above 400˚F (200˚C) will burn out your mug element and
may cause a re hazard.
5
www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Mug Press Overview
TOP VIEW FRONT VIEW
LEFT VIEW RIGHT VIEW
Bae Valve
Handle Bar Grip
Mug Heater Bae
Interchangable
Element
Pressure
Adjustment
Knob
Power ON/
OFF Switch
Digital
Controller
Limited
Switch
TOP VIEW
SIDE VIEW
6www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Machine Parts Diagram
7
www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Setting Up Your Mug Press
Turning On Your Mug Press
Turn the Main Power Switch ON. The
Main Power Switch is at the right/Left side
of the heat press.
Current temperature will display. Usually has the value
“LO”, indicating low temperature.
How to Read The Display
1.) Left side PV value = Current Temperature
2.) Right side PV value = Current Time
3.) Left side SV value = Set Press Temperature
4.) Right side SV value = Set Press Time
Setting Press Temperature
Press OK to start. Use the up and down
arrows to choose to display in °F or °C.
°F stands for Fahrenheit
°C stands for Celsius
Once selection is made, press OK to save
Now use the arrow to change the value of the set
temperature. The left light in the middle is lit to
indicate you are in the set temperature mode.
Setting Press Time
Green Set Time Value will ash
Use the up and down arrows to change
the value.
Press OK to save the value.
Wait until the current
temperature is the same as the set temperature
before using. The press will beep once set temperature
is reached. Close and open the press to stop the beeping.
Note: This mug press should not be set to exceed 400˚F/ 200˚C. Setting the press temperature to
above 400˚F/ 200˚C will burn out your mug element and may cause a re hazard.
8www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Elements Overview
2.5oz Expresso Shot
Element
SKU: X-HP-JMP61-06
1.5oz Shot Element
SKU: X-HP-JMP61-05
● 1.5oz Shot Glass
17oz Latte Element
SKU: X-HP-JMP61-04
● 12oz Wine Cup with Lid
● 16 Stainless Steel Tumbler
● 17oz Latte
12oz Latte Element
SKU: X-HP-JMP61-03
● 12oz Latte
6oz-10oz Mug Element
SKU: X-HP-JMP61-02
● 12oz Enamel Cup
● 10oz Bone China Mug with
Gold Rim
11oz/15oz Mug Element
SKU: X-HP-JMP51-01
● 11oz Mug
● 15oz Mug
Tumbler Element
SKU: X-HP-JMP61-01
● 20oz SS tumbler with Lid
and Straw
● 500ml SS Flask Bottle
● 17oz Coke Shaped Bottle
● Water Bottle with Bamboo
lid
● 650ml Aluminium Bottle
with Straw
● Stainless Steel Water Bottle
● Aluminum Water Bottle
● 10oz SS Coee Mug
● 12oz Mason Jar
● 14oz/ 17oz Travel Mug
● 16oz /20oz Beer Stein
9
www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Pressing a Drinkware
1.) Turn OFF the Power Switch.
2.) Change to the correct element (see Page 8), and turn ON the Power Switch.
2.) Set the appropriate Press Temperature, and Time.
3.) Tape your imaged transfer/sublimation paper to your mug with heat tape.
4.) Set the pressure. To do this, place a blank drinkware into the element.
Adjust the pressure knob until the drinkware ts snuggly in the element with
the heat shield wrapped around the bottle (just enough pressure so that the
drinkware cannot be moved once press is closed).
Turn pressure knob counter-clockwise to tighten and clockwise to loosen.
5.) Wait until current temperature is the same as set temperature. Once the mug
press is at temperature, place drinkware into the press. Close the mug press.
Note: Ensure the timer starts immediately after closing the press. If it does
not, take the bottle out & wait for the temperature to go up to the set temp.
6.) Timer will start counting down. The press will beep when the set time has
lapsed. When mug press beeps, open mug press and take out your drinkware.
7a.) For sublimation, peel immediately and dunk into warm-cold water to stop the
sublimation process.
7b.) For Hard Surface Papers, Dunk in warm-cold water. Then wait until the
mug is cold before peeling.
Please note: To image an 11oz/15oz Mug, you need to purchase Element: X-HP-JMP51-01.
Operating Process
10 www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON
Replacing your Mug Element
1.) Ensure the power switch is OFF.
2.) Unplug the mug press if it is still plugged in.
3.) Detach the mug element cord from the mug press. Unscrew the ring that holds
the cord in place before detaching. See below diagram for detailed instructions
4.) With the Mug Press open, unscrew the eight screws that hold the mug
element in place.
5.) Gently slide the mug element out of the mug press. Please be careful not to
damage the cord or the mug press.
6.) Gently slide the new mug element into the mug press.
7.) Re-screw the four screws to keep the mug element in place.
8.) Connect the new mug element cord to the mug press.
Ensure that the pattern on the cord matches the socket on the mug press.
Replacing The Mug Element
Mug Element
Cord and Ring
4 Screws that
Hold Mug
Element in Place
4 Screws that
Hold Mug
Element in Place
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Joto
Joto
Joto E-HP-JLF-3243 Manual de usuario
Joto
Joto E-HP-JAR-DS-1620 Manual de usuario
Joto
Joto XSTM-40 Manual de usuario
Joto
Joto E-HP-JAR-1515 Manual de usuario
Joto
Joto MugPress Manual de usuario
Joto
Joto E-HP-JMP-1S2E Manual de usuario
Joto
Joto SwingAway E-HP-JSA-1620 Manual de usuario
Joto
Joto E-HP-JSP-1620 Manual de usuario
Joto
Joto E-HP-JMP-51N Manual de usuario
Joto
Joto E-HP-JAR-DS-1620 Manual de usuario
