Johnson Controls AIM-200 Manual de usuario
FC-2000 Technical Manual 406
Addressable Intelligent Module Section
Technical Bulletin
Issue Date 0794
©1994 Johnson Controls, Inc. 1
Order No. 406-080
Introduction Page 3
Description 3
Inventory 4
Optional Peripherals 6
Installing the AIM-200 9
Installing the AIM-200 9
Wiring the Communications Loop Circuit 12
M500XJ Isolator Module 24
M500MJ Monitor Module 25
M501MJ Monitor Module 26
M500MJ and M501MJ Monitor Module Technical Notes 26
M510CJ Control Module 29
BGX-101 Addressable Manual Pull Station 33
Intelligent Detectors 34
Inserting the AIM-200 Cards 34
Programming the AIM-200 37
Programming Display 37
Auto-Program Mode 40
AIM-200 Power Requirements 41
Regulated Power Required in Standby 41
Regulated Power Required in Alarm 41
2Addressable Intelligent Module—AIM-200 Addressable Intelligent Module
AIM-200 Point Annunciation Page 43
Program Clear 44
Default Zone Map 45
Display Status 45
Program Edit 47
Alarm Bus 48
General Alarm Service 49
Backup Alarm Bus 50
Signal Silence Function 50
Operating M510CJ Control Modules 51
General Alarm 51
Control-by-Zone 52
Control-by-Module 52
Control-by-Detector 53
General M510CJ Trouble 53
Non-Silenceable Indicating Appliance Circuit 53
Non-Silenceable Form-C Relays 53
Supervisory Zones 53
Alarm Verification 54
Waterflow Zones 54
Walk Test 54
Trouble Condition 54
Step Switches 55
Loop Fault LED and RESET 55
ON-LINE LED and SKIP Switch 55
ENTER LED and Switch 55
Display Status LED and Switch 55
Automatic Detector Test 55
Operating the AIM-200 59
Zone Display 59
Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 3
Introduction
Note: AIM-200 features discussed in this document are available with
AIM-200 software part number 73264 or greater.
The Addressable Intelligent Module (AIM-200) functions as an interface
between the FC-2000 Fire Alarm Control Panel andintelligent/addressable
devices. To the FC-2000, the AIM-200 looks like an IZM-8 Initiating
Zone Module. On its single communications loop, the AIM-200 will
communicate with up to 99 addressable modules and 99 intelligent
detectors. The AIM-200 will communicate with the following:
2551J Intelligent Photoelectric Smoke Detector
1551J Intelligent Ionization Smoke Detector
5551J Intelligent Thermal Sensor
M500MJ Addressable Monitor Module
M502MJ Addressable Monitor Module
M501MJ Miniature Monitor Module
M510CJ Addressable Control Module
BGX-101L Addressable Manual Pull Station
DH-500J Intelligent Duct Detector Housing
The 198 devices are mapped into eight software zones by the AIM-200.
The status of these zones is reported to the CPU-2000. The AIM-200
includes a digital display for identifying the exact device address within a
zone. The display is also used to display device types and analog detector
sensitivity values.
Although the AIM-200 is intended primarily as an initiating input module,
it can support M510CJ Control Modules on the loop. The M510CJ
modules may be mapped to AIM-200 zones much like outputs are mapped
to inputs during standard FC-2000 programming.
The AIM-200 may be mixed in a system with any of these system modules:
IZM-8 Initiating Zone Module
IZE-A Initiating Zone Expander
ICM-4 Indicating Circuit Module
ICE-4 Initiating Circuit Expander
CRM-4 Control Relay Module
CRE-4 Control Relay Expander
Description
4Addressable Intelligent Module—AIM-200 Addressable Intelligent Module
VCM-4 Voice Control Module
VCE-4 Voice Control Expander
DCM-4 Dual Channel Module
TCM-2 Time Control Module (Single hazard release)
TCM-4 Time Control Module (Multiple hazard release)
In addition, ACM remote annunciators, AMG-1 and FFT-7
voice/telephone modules, and several power supplies can be employed with
an AIM-200.
Up to ten AIM-200s may be installed in one FC-2000 for a capacity of
1,980 points (subject to limitations of system power supply). Refer to the
AIM-200 Power Requirementssection of this document.
Figure 1: AIM-200 Addressable Intelligent Module
Inventory
AIM-200
Addressable
Intelligent Module
Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 5
The AIM-200 communicates with up to 99 intelligent detectors and up to
99 addressable modules. The AIM-200 reports device alarm or trouble
activity back to the CPU as one of eight mapped zones.
Figure 2: AIM-200 Label Inserts
The slide-in labels are printed with identification for system-defined LEDs
and switches. Space is provided to type in custom information for the
eight user-defined zones.
Figure 3: AIM-200 Card File
A special card file is attached to the bottom front of the AIM-200. Several
standard 4 in. by 2-1/4 in. cards are provided and may be marked with
device information by the installer. A reference card, which defines all
display codes, is included.
Label Inserts
Card File
6Addressable Intelligent Module—AIM-200 Addressable Intelligent Module
B501BJ Base
These intelligent, addressable detectors provide analog information to
the AIM-200. The AIM-200 processes this analog information and
continually makes decisions on the alarm, maintenance, or normal status
of each device. Each detector head mounts to a B501BJ base for ease of
installation or replacement. The sensitivity of each detector can be set
by the programmer at the AIM-200 for one of three levels (low,
medium, and high). Each detector responds to an address that is set in
the head via built-in rotary decimal switches.
2551J
An intelligent photoelectric smoke detector that provides analog
measurements of the optical smoke level in its chamber to the AIM-200
panel.
1551J
An intelligent ionization smoke detector that measures the level of
combustion products in its chamber using the ionization principle and
reports this measurement to the AIM-200.
5551J
An intelligent thermal sensor (135-degree F fixed temperature).
RA400Z
A remote single LED annunciator that can be wired directly off of an
addressable detector for annunciation of that detector’s alarm status.
Control and Monitor Modules
The M510CJ control module and the M500MJ monitor module provide
the interface between the FC-2000 and conventional initiating and
indicating devices. Both types of modules respond to an address that is
set by the installer with built-in rotary decimal switches. A flashing LED
indicates power is applied. A thermoplastic cover (illustrated at left) is
provided with each module for mounting to a 4-inch square mounting
box.
Optional
Peripherals
Intelligent
Detectors
Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 7
M500MJ
An addressable monitor module that can be used to monitor
conventional normally open contact alarm initiating devices, such as
manual pull stations, 4-wire smoke detectors, heat detectors, waterflow,
and supervisory devices. Supervised circuit can be wired NFPA Style B
or Style D.
M502MJ
An addressable monitor module that monitors conventional 2-wire
smoke detectors. Supervised circuits can be wired NFPA Style B or
Style D. M502MJ supervises initiating device circuit wiring,
communication loop, and input power.
M510CJ
An addressable control module that can be used as an indicating
appliance circuit for powering and supervising compatible, UL Listed
indicating appliances. Supervised circuits can be wired NFPA Style Y or
Style Z. By breaking two built-in tabs, the M510CJ can be employed as
a Form-C control relay.
M500XJ
The loop isolator module is an automatic switch that opens the circuit
voltage to a predetermined communications loop branch(es) whenever a
fault is detected on that circuit. The remainder of the communications
loop leading up to the M500XJ will continue to operate, unaffected by
the fault.
M501MJ
An addressable module that is functionally identical to an M500MJ
monitor module (Style B circuits only), but offered in a smaller package
for mounting directly in the electrical box of the device being monitored.
BGX-101L
The addressable manual pull station features a key-lock reset. The pull
station responds to an address set by the installer with built-in rotary
decimal switches. Includes key.
A2143-00
The 47K end-of-line resistor assembly is used in the supervision of
M500MJ Monitor and M510CJ Control Module circuits. It is included
with each M500MJ or M510CJ module.
8Addressable Intelligent Module—AIM-200 Addressable Intelligent Module
A77-716-02B
The end-of-line power supervision relay is used to supervise the power
to 4-wire smoke detectors and indicting appliances.
N-ELR
The N-ELR resistor assortment is required for use in Canada. It
provides a variety of resistor values to mount to a single ELR plate
(included). Resistors can be used for the supervision of an M500MJ
monitor module or M510CJ control module circuit.
Resistors included:
120 ohms, 470 ohms, 1.8K, 2.2K, 4.7K, 6.8K, 10K, 27K, and 47K.
Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 9
Installing the AIM-200
This section outlines the installation procedure for the AIM-200. For
information on installing other FC-2000 equipment, refer to the Installing
the FC-2000Technical Bulletinin this manual.
Complete the following steps to install the AIM-200 onto the CHS-4
Chassis.
1. Mount the AIM-200 to a CHS-4 Chassis.
2. Insert the tab on the bottom of the AIM-200 into the slot on the
bottom of the CHS-4.
3. Fasten the AIM-200 to the top of the CHS-4 using the two captive
screws in the top corners of the module. Refer to Figure 4.
Note: If point annunciation (192 intelligent AIM-200 points and
56 standard system circuits) of a single AIM-200 is desired, the
AIM-200 must be mounted in the second slot of the first chassis
(directly to the right of the CPU). This annunciation option must
also be selected in system programming.
Installing the
AIM-200
10 Addressable Intelligent Module—AIM-200 Addressable Intelligent Module
Figure 4: Mounting the AIM-200
Este manual sirve para los siguientes modelos
10
Tabla de contenidos
Otros manuales de Sistema de control de Johnson Controls
Johnson Controls
Johnson Controls Penn System 450 Series Manual de servicio
Johnson Controls
Johnson Controls YORK YLAA0189SE Manual de usuario
Johnson Controls
Johnson Controls FC-2000 Manual de referencia
Johnson Controls
Johnson Controls System 450 Series Manual de servicio
Johnson Controls
Johnson Controls VMA1200 Series Manual de servicio
Johnson Controls
Johnson Controls Unisab III Manual de usuario
Johnson Controls
Johnson Controls SABROE Unisab III Control Manual de instalación y operación
Johnson Controls
Johnson Controls CCXL01 Manual de instalación y operación
Johnson Controls
Johnson Controls MS2 Manual
Johnson Controls
Johnson Controls CMS-1655 Manual de usuario
Johnson Controls
Johnson Controls Unisab III Manual de usuario
Johnson Controls
Johnson Controls ZZ Series Manual de usuario
Johnson Controls
Johnson Controls SABROE Unisab III Control Manual de instalación y operación
Johnson Controls
Johnson Controls Penn MR4 Manual
Johnson Controls
Johnson Controls HomeLink Manual de usuario
