Johnson Controls IFC-200 Guía de referencia

IFC-200 Technical Manual 444

Hardware Installation Section

Technical Bulletin

Issue Date 1293

Order No. 444-040

IFC-200 Hardware Installation Procedures

Hardware Installation Procedures Page 5

●

General 5

- Backbox Mounting 5

●

Power Supplies 6

- DC Power Output Connections 7

- AC Power Connections 7

- Battery Power 7

●

Output Circuits 8

- Indicating Appliance Circuits 8

- Releasing Circuits 8

●

Standard Relays 9

●

Remote Printers 9

- Installation 10

- Printer Configuration 10

- PRN-3 Setup Paper Feed Advance 11

- Keltron Printer Option 12

●

CRT-1 Configuration 12

- Function Key Programming 14

●

Wiring the Signaling Line Circuit 14

- Isolator Modules 14

- Monitor Modules 15

- Control Modules 15

- Intelligent Detectors 15

- Device Capacity 15

- SLC Resistance Measurement 16

- Isolator Module Operation 20

- SLC Shield Termination 21

2 Hardware Installation—IFC-200 Hardware Installation Procedures

●

Isolator Module 23

●

M500MJ Monitor Module 23

- SLC Connections 23

- NFPA Style B Initiating Device Circuit 24

- NFPA Style D Initiating Device Circuit 24

- Test Switch 24

●

M501MJ Monitor Module 24

- NFPA Style B Initiating Device Circuit 25

●

M502MJ 25

- SLC Connections 25

- NFPA Style B Initiating Device Circuit 25

- NFPA Style D Initiating Device Circuit 26

●

Control Module 30

- SLC Connections 30

- NFPA Style Y Indicating Appliance Circuit 30

- NFPA Style Z Indicating Appliance Circuit 30

- Indicating Appliance Power 31

- Test Switch 31

- SLC Connections 31

- Contact Connections 31

●

Addressable Manual Pull Station 34

- BGX-101L Installation 34

●

Intelligent Detectors 35

- Installation 35

●

Optional Modules 36

- Optional Module Installation 36

- RTM-8 Option Module 36

●

NR45-24 Remote Battery Charger 39

- Connecting the Primary Power Source 39

- Connecting the Secondary Power Source 39

Hardware Installation—IFC-200 Hardware Installation Procedures 3

Supply Calculations Page 43

●

AC Branch Circuit 43

●

Main Power Supply 43

- Smoke Detectors 43

- Standby Current Load on Batteries 45

- Four-Wire Detectors 45

- Alarm Current Load on Batteries 45

- Calculating Necessary Battery Size 45

Wire Requirements 47

4 Hardware Installation—IFC-200 Hardware Installation Procedures

Hardware Installation—IFC-200 Hardware Installation Procedures 5

Hardware Installation

Procedures

This IFC-200 Hardware Installation Procedures Technical Bulletin is

divided into three major sections. The Hardware Installation Procedures

section contains step-by-step instructions to help you install the hardware

related to the IFC-200 Fire Control System. The Supply Calculations

section helps you determine the required current, current loads, and power

to support the IFC-200. Specific wiring information for each circuit in the

system is found in the Wire Requirements section. Read this document

before attempting to install the IFC-200 hardware.

1. Carefully unpack the system and check for shipping damage.

2. Mount the cabinet in a clean, dry, vibration-free area where extreme

temperatures are not encountered. The area should be readily

accessible with sufficient room to easily install and maintain the

panel.

3. Locate the top of the cabinet approximately five feet above the floor

with the hinge mounting on the left.

4. Determine the number of conductors required for the devices to be

installed.

5. Pull the required conductors into the box through the knockout

provided.

All wiring should be in accordance with the National and/or Local codes

for fire alarm systems.

1. Remove the main PC board assembly by unscrewing the four screws

in the corners of the board. Set the board aside in a safe, clean place.

Avoid static discharge, which may damage the board.

2. Mark and pre-drill the four mounting bolts using the dimensions

shown in Figure 1.

3. Install two upper fasteners in wall with screw heads protruding.

4. Using upper keyholes, mount the backbox over the two screws.

Tighten the screws.

5. Install the lower two screws.

6. When location is dry and free of construction dust, reinstall the main

PC board.

General

Backbox

Mounting

6 Hardware Installation—IFC-200 Hardware Installation Procedures

1.00 14.5

12.5

0.5

9.5 16.0

200bckbx

Mounting Holes

Primary Power

120 VAC

Low Voltage

Wiring

Figure 1: IFC-200 Backbox Mounting

Note: Insert all cables from the side of the cabinet. Do not insert wiring

from the back of the cabinet. Note the entry locations of primary

120 VAC power and low voltage wiring above.

CAUTION: Damage may occur when removing and/or

inserting cards, modules, or interconnecting cables

while this unit is energized. Several different

power sources can be connected to this panel.

Disconnect all power sources before servicing.

Power Supplies

Hardware Installation—IFC-200 Hardware Installation Procedures 7

All DC power outputs are power-limited.

High Ripple Regulated Power

24 VDC power for indicating appliances

TB1 Terminal 1 (+) and 2 (-).

Note: This power is unsuitable for all

RS-485 annunciation devices,

except the ACM-8R.

1.0 amps standby

2.25 amps alarm

Non-resettable Power

24 VDC filtered, regulated,

non-resettable power can be

drawn from TB1 Terminals 3 (+)

and 4 (-). This power is suitable

for all RS-485 annunciation

devices. 0.50 amps

4-wire Smoke Detector Power

24 VDC filtered, regulated,

resettable power for 4-wire smoke

detectors can be obtained from TB1

Terminals 5 (+) and 6 (-). 0.50 amps

dcpowr

1 2 3 4 5 6

+ - + - + -

Figure 2: DC Power Output Connections

Primary power required for this panel is 120 VAC, 50/60 Hz, 3.0 amps.

Overcurrent protection for this circuit must comply with Article 760 of the

National Electrical Code (NEC) and/or local codes. Use 14 AWG or

larger wire with 600 volt rating.

AC Power Battery

Power

acbatpwr

Figure 3: AC Power Connections and Battery Power

Observe polarity when connecting the battery. Connect the battery cable

to J3 on the main board using the plug-in connector provided. An MTA

connector tool is required. Refer to Figure 1 in the IFC-200 System

Description Technical Bulletin in this manual for the location of J3. See

the Supply Calculations section of this document to calculate the correct

battery rating.

CAUTION: Sulfuric acid in batteries can cause severe burns to the

skin and eyes and can destroy fabrics. If contact is

made with sulfuric acid, immediately flush skin or

eyes with water for 15 minutes and seek immediate

medical attention.

DC Power Output

Connections

AC Power

Connections

Battery Power

8 Hardware Installation—IFC-200 Hardware Installation Procedures

The IFC-200 provides four indicating appliance circuits (Style Y only).

Each circuit is capable of producing 2.25 amps of current at 24 VDC.

Total current drawn from these, as well as any other panel DC power

outputs, cannot exceed 5.0 amps. Use UL Listed 24 VDC indicating

appliances only. Circuits are supervised and power-limited. See

Figure 23 for a list of recommended compatible indicating appliances.

Any or all of these circuits may be used as a releasing circuit by

programming it for RELEASE CKT. See the Releasing Applications

section of the IFC-200 Applications Technical Bulletin in this manual for

more information, including a list of compatible solenoid valves.

B+ B- B+ B- B+ B- B+ B-

1 2 3 4 5 6 7 8

+ -

Style Y Indicating Appliance Circuit (Supervised and Power-limited)

Polarized Bell

Polarized Strobe

Polarized Horn

4.7K, 1/2 W (Part No. 71252, UL Listed)

(Supervisory Voltage is 2-3 VDC)

Releasing Circuit

(Supervised and Power Limited)

Dummy Load

All Unused

Circuits 4.7K, 1/2 W

Note: Indicating circuit polarity is shown in the

alarm

state.

tb2conn

Circuit 1 TB2 1 and 2

Circuit 2

Circuit 3

Circuit 4

TB2 3 and 4

TB2 5 and 6

TB2 7 and 8

Figure 4: Circuit Connections

Output Circuits

Indicating

Appliance

Circuits

Releasing

Circuits

Hardware Installation—IFC-200 Hardware Installation Procedures 9

The IFC-200 provides a set of Form-C alarm contacts and a set of Form-C

trouble contacts rated for 2.0 amps at 30 VDC (resistive). The panel also

provides a Form-A supervisory contact rated for 2.0 amps at 30 VDC

(resistive). These contacts are derated to 0.5 amps at 30 VAC.

NO C NO NC C NO NC C

tb3conn

1 2 3 4 5 6 7 8

SUPV ALARM TROUBLE

Figure 5: Relay Connections

The PRN-3 Remote Printer provides a hardcopy printout of all status

changes within the system and time-stamps the printout with the current

time of day and date. The PRN-3 provides 80 columns of data on standard

9 inch by 11 inch tractor-feed paper.

3 2 17

TX REF RX REF OUT OUT IN IN A B B+- A+- B- A-

Plug this DB-25 connector into the

RS-232 printer port.

Connect CRT-1 pin 3 to TB4 TX.

Connect CRT-1 pin 7 to TB4 REF.

Connect CRT-1 pin 2 to TB4 RX.

PRN-3

prn3conn

PRN-3

IFC-200

System Common (-)

IFC-200, TB1-2, or Enclosure

Figure 6: Remote Printer Connections

Standard

Relays

Remote Printers

10 Hardware Installation—IFC-200 Hardware Installation Procedures

Note: The RS-232 printer interface may also be used with EDP-listed

equipment, such as personal computers, to monitor the IFC-200 for

supplementary purposes.

Since the IFC-200 is not the receiving unit in a proprietary system, its use

is optional from a standards compliance standpoint. Remote printers

require 120 VAC, 50/60 Hz primary power. A secondary power source

(battery backup) is not provided; the use of a separate Uninterruptible

Power Supply (UPS), UL Listed for Fire Protection Signaling is

recommended.

The IFC-200 and PRN-3 connect via an RS-232 interface. A custom cable

must be assembled for connection to the printer’s RS-232 port.

Refer to the documentation supplied with the PRN-3 for instructions on

the printer’s menu controls. Set the printer’s options as listed in Table 1.

Table 1: PRN-3 Printer Options

Under the Menu Area:

Character Density 10 CPI

Character Presentation

Character Set Standard

Italic No

Proportional No

Slashed Zero Yes

Courier ISO/PC/Epson 0

National Character 11 (E-US ASCII)

Line Density 6 LPI

Paper Form 11

Skip Over Fold 0.5

Printer Options

Paper Options No Option

Selected Paper Path Push Tractor

Ribbon Options No Option

Left Margin 1

Right Margin 80

Horizontal Tabs 25

No Vertical Tabs Set

Top Margin Top of Form

Bottom Margin 10.5 Inches

Vertical Alignment 12-1/72 Inches

Under the Technical Listing Area:

Auto PrintPrint Commands CR

CR Implies LF No

Continued on next page . . .

Installation

Printer

Configuration

Otros manuales para IFC-200

Tabla de contenidos

Otros manuales de Panel de control de Johnson Controls

Johnson Controls

Johnson Controls Frick QUANTUM HD VILTER Manual de usuario

Johnson Controls

Johnson Controls T20 Manual de usuario

Johnson Controls

Johnson Controls S1-TTSCC01 Guía

Johnson Controls

Johnson Controls IFC-200 Manual de usuario

Johnson Controls

Johnson Controls Frick QUANTUM Series Guía

Johnson Controls

Johnson Controls Frick QUANTUM LX Guía

Johnson Controls

Johnson Controls FRICK QUANTUM HD Guía

Johnson Controls

Johnson Controls Bentel Security tyco ABSOLUTA Plus Guía del usuario

Johnson Controls

Johnson Controls Frick QUANTUM LX Manual de instrucciones

Johnson Controls

Johnson Controls IQ Panel Manual de usuario

Johnson Controls

Johnson Controls IQ4 NS Manual de usuario

Johnson Controls

Johnson Controls IFC-3030 Manual de usuario

Johnson Controls

Johnson Controls CIW01 Manual de usuario

Johnson Controls

Johnson Controls FRICK QUANTUM LX AcuAir Guía

Johnson Controls

Johnson Controls FRICK QUANTUM LX AcuAir Manual de uso y cuidado

Johnson Controls

Johnson Controls IFC-200 Manual de usuario

Johnson Controls

Johnson Controls FRICK QUANTUM LX/HD Manual de usuario

Johnson Controls

Johnson Controls Tyco PowerSeries Pro HS2TCHPRO Manual de usuario

Johnson Controls

Johnson Controls S1-TTSCC01 Guía de inicio rápido

Johnson Controls

Johnson Controls IFC-3030 Manual del propietario

Johnson Controls

Johnson Controls Qolsys IQPK048 Manual de usuario

Johnson Controls

Johnson Controls YORK OPTIVIEW CONTROL CENTER Manual de usuario

Johnson Controls

Johnson Controls Frick QUANTUM LX Manual de usuario

Johnson Controls

Johnson Controls IFC-3030 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas