Johnny's Selected Seeds Connecta Tool System Guía de configuración rápida

SEED BREEDERS, GROWERS, AND MERCHANTS SINCE 1973

955 Benton Ave., Winslow, ME 04901 •Phone: 1-877-564-6697 •Fax: 1-800-738-6314

Email: service@johnnyseeds.com •Web Site: Johnnyseeds.com

Materials Included

•(1) ConnectaTM Receiver

•(1) Oiled ashwood handle

•(1) #6 x ¾" Rounded-head stainless steel wood screw

Additional Tools Needed

•#1 Phillips screwdriver

•3/32" Allen wrench

ASSEMBLY INSTRUCTIONS

The ConnectaTM Receiver comes fully assembled and only requires the oiled ashwood handle to be attached

before use.

1. Insert the tapered handle into the metal receiver as far as it will go, until it is secure in place.

Note: Do not push the receiver down too far onto the handle as it could cause unnecessary strain on the

screws.

2. Secure the wooden handle into the metal receiver by inserting the #6 x ¾" wood screw provided into the

screw hole and tightening it with a #1 Phillips screwdriver.

OPERATION & USE

•To attach a tool head into the receiver, press the button and insert the tool head shank until it clicks

securely into place. You will need to gently push it in so the rubber gasket depresses to form a tight fit.

Note: Be sure the thumb grip on the tool head is in line with the receiver’s button.

•To remove a tool head, press the button and slide the tool head out of the ferrule.

•Extra tool heads for the ConnectaTM Tool System can be stored on the

belt loop clip, allowing you to swap tool heads quickly and easily in the

field.

•Important Note: The ConnectaTM Tool System is designed with tight

tolerances to keep the heads from shifting while in use. You may need

to insert new heads a few times before they fit snugly in the receiver.

ConnectaTM Tool System

Assembly, Use & Maintenance

Tool

shank

Thumb

grip

Button

Receiver

Belt loop clip

Tool shank

SEED BREEDERS, GROWERS, AND MERCHANTS SINCE 1973

MAINTENANCE

•Always store your ConnectaTM Tool System components clean and dry.

•If dirt or debris gets inside the receiver, gently shake it upside-down to clean it out.

Note: DO NOT tap the receiver on a hard surface such as stone or concrete, as this could damage it.

•If the dirt or debris is particularly difficult to remove, you can spray water down into the receiver until it is

cleared. Allow the receiver to fully air-dry before use.

•A light coat of linseed oil can be applied to the wooden handle as needed.

Cleaning Inside the ConnectaTM Receiver

If necessary, the ConnectaTM Receiver can be disassembled for a more thorough cleaning.

•Remove the four #4-40 3/32" socket head screws from the bottom half of the receiver with a 3/32" Allen

wrench.

•Remove the button from the top half of the receiver and both ¼" compression springs housed below it.

•Clean out the receiver with water and allow all parts to completely dry before reassembling.

•You can lubricate the sides of the button and the springs with a couple drops of food-safe oil, if

necessary.

06.27.2022 | JG, ms

Wood screw

Socket head

screws

Compression springs

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Johnny's Selected Seeds

Johnny's Selected Seeds

Johnny's Selected Seeds Bio Plus PATIO Manual de usuario

Johnny's Selected Seeds

Johnny's Selected Seeds Tilther Manual de usuario

Johnny's Selected Seeds

Johnny's Selected Seeds 9414 Manual de usuario

Johnny's Selected Seeds

Johnny's Selected Seeds 7621 U-Bar Double Wheel Hoe Manual de usuario

Johnny's Selected Seeds

Johnny's Selected Seeds The Neversink Farm Zipper Guía de configuración rápida

Johnny's Selected Seeds

Johnny's Selected Seeds 7239 Manual de usuario

Johnny's Selected Seeds

Johnny's Selected Seeds Tilther XT Guía de configuración rápida

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario