JMK CLOCKstep:MULTI Manual de usuario
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
1
Product Specificaons 25
Table of Contents
Introducon 2
Patch Bay Connecons 3
Rear Connecons 4
USB Connecon 4
Global Sengs 16
Presets 15
Metronome 11
User Interface 5
Limited Warranty 25
MIDI In Specificaon 22
Connecons 3
Transport and Clock 6
Tempo 9
Sync Rates 13
External Clock Sync 19
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
2
A full MIDI Implementaon allows CLOCKstep:MULTI to be controlled remotely
from an external MIDI device.
CLOCKstep:MULTI is a MIDI Clock, CV Sync, Transport Controller and Audio
Metronome all in one box.
All of these features can be organized and stored into 40 Presets.
Clock and Transport funcons can either be controlled independently or in unison
depending on the user’s Transport Mode selecon.
The Audio Metronome is configurable with a variety of sounds, independent
subdivision volumes and Time Signatures.
Hooked up to a dedicated Audio Output from a DAW, it can deliver perfectly med
sync between the DAW and other connected hardware devices. (aka: Sample
Accurate Sync)
The two (2) CV Trigger Sync Outs can be independently configured for different
sync rates to interface with a variety of modular/Eurorack Synths, Sequencers,
Drum Machines and Loopers.
Introducon
MUTE
SOUND VOLUME
234
TEMPO
TRIPLET
:
SYNC
12
PLAY RESET
START STOP
SYNC 1SYNC 2PRESET
START/
STOP
MIDI
OUT
View Introduction Video
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
3
Patch Bay Connecons
START/STOP
0/+5 Volt Trigger to toggle sending
both Start and Stop commands.
PLAY
0/+5 Volt Gate for
sending Transport
Start and Stop
commands. Signal
is HIGH when
Transport is started
and LOW when
stopped.
0/+5 Volt Triggers for sending clock signals. Clock rate is
configurable independently for each sync output.
SYNC 1 & 2
PLAY RESET
START STOP
SYNC 1SYNC 2
START/
STOP
MIDI
OUT
RESET
0/+5 Volt Trigger for
sending a command
to reset a sequence
from the beginning.
Sent with a Start
command, except
when resuming from
Pause.
0/+5 Volt Trigger for
sending a discrete
Transport Start
command.
START STOP
0/+5 Volt Trigger for
sending a discrete
Transport Stop
command.
MIDI OUT
TRS “Type A” MIDI Output which
mirrors the MIDI DIN Output.
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
4
Rear Connecons
MIDI IN MIDI OUT
9v DC
ON
OFF
AUDIO OUT
(CLICK)
AUDIO IN
(SYNC)
JMK MUSIC PEDALS
AUDIO IN
(SYNC)
TS Line Level
Audio Input for
receiving 24
PPQN audio
pulses from a
DAW or other
compatible audio
device.
AUDIO OUT
(CLICK)
TS Line Level
Audio Output for
sending Click
audio to a mixer
for tempo
monitoring.
Standard DIN Connector for
receiving MIDI data.
MIDI IN MIDI OUT
Standard DIN Connector for
sending MIDI OUT and THRU
data.
POWER
Center Negative.
2.1mm Barrel
Connector.
9v DC. 200 mA
Nominal current.
On the right side is a USB connecon. This is a Class-Compliant MIDI Client
connecon that will be seen as a 1x1 MIDI connecon on a host computer. It’s also
used for updang the firmware.
USB Connecon
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
5
User Interface
MUTE
SOUND VOLUME
234
TEMPO
TRIPLET
SYNC
12
PRESET
Each buon is labeled for its primary funcon.
The User Interface is comprised of a grid of 16 backlit buons.
When accessing certain features, the arrangement will change
to indicate a new set of choices. In many cases, the new
arrangement is for selecon of a value between 1-16 from le
to right and top to boom, where the Top Le buon is 1 and
the Boom Right buon is 16.
All arrangements and selecons are detailed in the coming
chapters.
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
6
There are 2 buons for controlling Start,
Stop, Pause and Connue.
How these buons work will be determined
by the user’s choice of Transport Mode. The
descripon of each of the modes is covered
below.
Changing the Transport Mode is covered in
the Global Sengs chapter.
Transport and Clock
MUTE
SOUND VOLUME
234
TEMPO
TRIPLET
SYNC
12
PLAY RESET
START STOP
PRESET
4
While paused, this buon is used to resume the Clock and send
Start/Connue commands to all connected devices.
While started, this buon is used to Pause the Clock, which results in
sending a Stop commands to all connected devices.
Simple Transport Mode
The Clock/Stop buon is used to Stop the unit if it is currently
started or paused.
Starng or Stopping the Clock cannot be performed independent of the
Transport commands in Simple Transport Mode.
This is the default mode of CLOCKstep:MULTI.
The Start/Pause buon is used to simultaneously begin
running the Clock and send Start commands to all connected
devices.
connued ...
View Transport Video
View Synchronize Video
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
7
Resync Transport Mode
If the Clock is not currently running, the Start/Pause buon is
used to simultaneously run the Clock and send Commands to
all connected devices.
Similar to Simple Transport Mode, but in this mode Pause is replaced by a
Resync funcon.
While started, this buon is used to Resync the Metronome Bar and all
connected devices (by sending Stop, Reset, Song Posion Pointer=0 and
Start in that order).
If the clock is currently running, this buon sends the Resync command set
while simultaneously aligning the Metronome Bar to this point.
Starng or Stopping the Clock cannot be performed independent of the
Transport commands in Resync Transport Mode.
While started, the Clock/Stop buon is used to send Stop
commands to all connected devices. This does not stop CS:M’s
own Clock and Metronome unl you press it a second me.
While started, this buon is used to Pause the Clock and send a Stop
command to all connected devices.
A hybrid of the previous 2 modes, this mode offers more funconality from
using only 2 buons.
The Start/Pause buon is used to simultaneously begin
running the Clock and sending Start commands to all
connected devices.
The Clock/Stop buon is used to Stop the unit if it is currently
started.
While paused, this buon is used to resume the Clock and send
Start/Connue commands to all connected devices.
Align Transport Mode
While stopped, this buon can be used to begin running CS:M’s internal
Clock independently of Transport commands, which also begins running the
Metronome. Only the Clock pulses are sent to other devices, there are no
other commands transmied.
Transport and Clock (connued)
connued ...
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
8
Quanze Transport Mode
If the Clock is currently running, this buon will place Start into a pending
state unl the top of the next Bar is reached, at which me all of the Start
commands are sent (in perfect me with the top of that Bar).
While started, this buon is used to Pause the Clock and send a Stop
command to all connected devices.
If the Clock is not currently running, the Start/Pause buon
will only respond by flashing, indicang that it is in a pending
state. The Start commands will be sent once the Clock begins
running.
This mode doesn’t have any rules. The Transport and the Clock funcons
are independent from each other except in the case of Pausing.
While started, the Clock/Stop buon is used to send Stop
commands to all connected devices. This does not stop CS:M’s
own Clock and Metronome unl you press it a second me.
While paused, this buon is used to resume the Clock and send
Start/Connue commands to all connected devices.
This mode ensures that the Start commands are always perfectly aligned
with the downbeat of the next Metronome Bar.
While stopped, this buon can be used to begin running CS:M’s internal
Clock independently of Transport commands, which also begins running the
Metronome. Only the Clock pulses are sent to other devices, there are no
other commands transmied.
Independent Transport Mode
Transport and Clock (connued)
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
9
Internal Clock rates range from 10 - 255
BPM.
Tap Tempo
Simply tap on the Tempo buon to
set a new tempo, using a Quarter
Note feel.
It’ll take several taps in order for the
tempo calculaon to begin.
MUTE
SOUND VOLUME
234
TEMPO
TRIPLET
SYNC
12
PLAY RESET
START STOP
PRESET
Tempo
Once 3 numbers have been entered, the
display will change and the boom row will
look like this image on the right.
One of the lights in the keypad will actually
be green, but ignore that for the moment.
It’ll be explained a lile further down.
Press the Red buon to Cancel.
Only input that is within the valid BPM
range is accepted, so for instance the first number entered cannot be a 5.
The operaon for entering BPM is exactly
the same as you would use a 10-key on a
calculator or keyboard, accepng 3
numbers in sequence. As you input the
numbers, the column of buons on the
right will turn green from top to boom to
indicate that the number has been
registered.
Exact Tempo
You can input an exact BPM by holding down the Tempo buon for 2
seconds. The lighng display will change to a calculator 10-key layout. (the
numbers overlaying the graphic below are for illustraon)
Press the Green buon (the calculator
‘Enter’ key) to immediately Execute the new Tempo with a .0 decimal.
connued ...
3
TEMPO
0
123
6
5
4
78 9
234
TEMPO
SYNC
12
View Tempo Video
version 1.0 (build 0050)
CLOCKstep:MULTI
Copyright 2023 JMK Music Pedals
JMK MUSIC PEDALS
10
Tempo (connued)
Tempo Decimal
Aer inpung the decimal value, you will be given only the opon of
Execung or Cancelling again.
Somemes you need to know what tempo CLOCKstep:MULTI is currently set
at. This is where that green light shown within the 10-key layout comes into
play.
If you’d like to enter a 1 point decimal
value, press the white buon at the final
stage, which is in the same place as a
calculator 10-key decimal. A 10-key layout
will appear again, waing for you to input
one more value.
To read the current tempo, press the Tempo key for 2 seconds to bring up
the calculator 10-key. The green light show in the 10-key is the current
value used. Follow pressing the green lights within the 10-key and you will
be re-entering the same BPM value that is currently running. Once at the
last stage, you can either Execute or Cancel.
Read the Tempo
External Clock Tempo
When CLOCKstep:MULTI is following an External Clock, the Tempo buon is
deacvated. Tempo can only be set by the External Clock device. See the
External Clock Sync chapter for more details.
234
TEMPO
SYNC
12
Tabla de contenidos
Manuales populares de Equipo de grabación de otras marcas
Strymon
Strymon NIGHTSKY Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario
Tews Technologies
Tews Technologies TPMC465 Manual de usuario
Honeywell
Honeywell Excel 50 Manual de usuario
SeaLevel
SeaLevel COMM+8.LPCI Manual de usuario
Arturia
Arturia AUDIOFUSE STUDIO Manual de usuario
