JLL IC300 Manual
INSTRUCTION GUIDE
IC300 MONITOR
The contents of this manual are subject to change without notice to improve quality.
© 2023 JLL Fitness Ltd
JLL Fitness Ltd owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of JLL Fitness Ltd is prohibited.
COPYRIGHT
CONTENTS
- Safety precautions
- Cleaning
- Installation
- Operation
Exiting scan mode
Resetting your monitor
- Data readouts
- Troubleshoot
- Contact details
p. 4
p. 5
p. 6
p. 7
p. 7
p. 7
p. 8
p. 9
p. 10
4
The monitor on this machine has been tested to the required standards, each of those passed regulations are shown via
the following symbols:
WEEE - Waste Electrical and Electronic Equipment Recycling.
ABS - Acrylonitrile Butadiene Styrene often referred to as ABS is a type of plastic that is an opaque thermoplastic.
CE - The product conforms with relevant EU directives regarding health and safety or environmental protection.
QC Pass - A product which has fullled the requirements of a technical control and passed the outgoing exams.
ROHS - This is an abbreviation for “Restriction of (the use of certain) Hazardous Substances in electrical and electronic
Equipment”.
SAFETY PRECAUTIONS
WEEE Symbol
ABS Recycling Symbol
EU Compliance Symbol
Quality Control Symbol
ROHS Symbol
5
CLEANING
Please take care when cleaning this monitor as the LCD screen can easily be scratched.
You will need a soft dry cloth
Do not spray cleaning chemicals directly onto the monitor
Do not apply water to the monitor as it is electrical and may damage the internal components
6
INSTALLATION
STEP 1 STEP 2
STEP 3
Insert the batteries, making sure they are the
correct way round.
Connect the male to female wires from the
base to the monitor.
Connect the pulse wire from the base to the
monitor.
STEP 4
Secure the monitor to the handlebars by slotting
it onto the frame.
7
OPERATION
The IC300 monitor has a total of 6 readouts, displaying:
Time Speed Distance Odometer Heart Rate Calories
When rst powered on, the monitor will automatically be in ‘Scan’ mode. This means the digits on the screen will change
every few seconds between time, distance, speed etc. This will allow you to have an overview while training without
pressing any buttons.
EXITING SCAN MODE
On this monitor there is only one button, press this to exit scan
mode and continuously press it to view each readout.
The arrow at the top of the screen will indicate which setting you
are currently viewing.
RESETTING YOUR MONITOR
To reset all of the readings to zero, press and hold the button for
a few seconds. You will then see the digits ash zero’s and the
monitor will beep.
8
DATA READOUTS
Readout Measurement
Time Minutes : Seconds
Speed MPH
Distance Miles
Pulse PPM (Pulsations Per Minute)
Odometer Miles
9
TROUBLESHOOT
Issue Resolutions
No power to the monitor • Make sure the batteries are fully inserted
and the correct way round.
• Check your connection wires from the
monitor to the base. They must not be
trapped, fully connected and the pins
must be straight.
Power but no readings • Check the small black sensor that is
inserted into the rear side of the casing.
If this is not inserted far enough it won’t
be able to read anything.
• However, do not push this sensor in too
far as it will catch on the chain.
No pulse reading • Make sure the pulse plates are clean and
dry.
• Do not have any lotion on your hands.
• Sweat can affect the reading.
• Make sure both hands are fully gripping
each plate.
10
CONTACT DETAILS
Tel: 0121 328 7507
Email: info@jlltness.co.uk
Live Chat: WWW.JLLFITNESS.CO.UK
Otros manuales para IC300
2
Tabla de contenidos
Otros manuales de Monitor de JLL
JLL
JLL AQUA 1 Manual
JLL
JLL CT200 Manual de usuario
JLL
JLL IC600 Manual de usuario
JLL
JLL IC260 Manual de usuario
JLL
JLL IC300 Manual de usuario
JLL
JLL CT100 Manual de usuario
JLL
JLL JF600 PRO Upright Bike Manual
JLL
JLL IC200 PRO Indoor Cycling Manual
JLL
JLL JF100 Manual de usuario
JLL
JLL JF150 Manual de usuario
