JLG SkyTrak Guía de configuración
1
31200804
1.1 GENERAL GUIDELINES
•This repair procedure provides repair information for
a specific discrepancy. It is the responsibility of the
entity performing the repairs to determine if the
discrepancy can be corrected by this procedure. This
procedure is for the repair of the boom pivot
weldment only.
1.2 PARTS REQUIRED
SkyTrak Boom Pivot Repair Kit:
P/N 1001141603
Note: * The Self Aligning Bearings P/N 8065641 will be
factory installed in the Boom Pivot Plate Weldment P/N
1001141633.
1.3 WELD REPAIR GUIDELINES
•All welding must be in strict accordance with
EN288-3, EN288-4 or ANSI/AWS D1.1 standards.
•Disconnect the battery of the machine being repaired
prior to welding.
•Ground only to the component being welded. Do not
ground to any adjacent component or allow pins,
wear pads, wire ropes, bearings, gears, seals,
valves, electrical wiring, or hoses to be between the
grounding position and the area to be welded.
1.4 TOOLS & EQUIPMENT REQUIRED
1. Stands and lifting equipment capable of lifting/
supporting the affected components
2. Hand-held power grinder
3. Air carbon-arc equipment
4. Electric welding equipment
5. AWS 70 grade, low hydrogen rod or wire
6. Standard welder tools
7. Standard mechanic tools
8. Paint
1.5 PERSONNEL REQUIRED
1. Qualified JLG Equipment Mechanic
2. Certified Welder
1.6 MODELS AFFECTED
SkyTrak 8042, 10042 & 10054
1.7 BOOM PIVOT WELDMENT REMOVAL
1. Park the machine on a firm, level surface, fully retract
the boom, lower the boom, place the transmission
control lever in (N) NEUTRAL, engage the park brake
and shut the engine OFF.
2. Place a Do Not Operate Tag on both the ignition key
switch and steering wheel, stating that the machine
should not be operated.
3. Open the engine doors. Allow system
fluids to cool.
4. Remove components as required to
facilitate repair.
Note: Refer to Service Manual 31200353,
Section 3.4.1 for detailed boom assembly
removal.
5. Protect any hoses, wires and hydraulic
cylinder rods before preparing or welding
in the frame boom pivot area.
6. Safely support the components to
alleviate pressure or stresses at the
affected repair area(s).
CAUTION
Use all applicable Safety precautions while working
on, around or under any machinery.
P/N Qty Description
1001141633 1 Plate, Boom Pivot
8065641* 2 Bearing, Self Aligning
NOTICE
Failure to comply with the above weld repair guidelines
may result in component damage.
SkyTrak Boom Pivot
Repair Instructions
For Kit 1001141603
A
02/12
31200804
An Oshkosh Corporation Company
2 31200804
SkyTrak Boom Pivot Repair Instructions For Kit 1001141603
7. Using a portable grinder or air carbon-arc equipment,
remove both boom pivot plates (1) from the pivot
tower weldment (2).
8. Inspect the affected area of the pivot tower weldment
for cracks. If any discrepancies are evident, notify
JLG Safety 1-877-554-7233 (877-JLG-SAFE) for
further evaluation.
9. Grind the repair area (3) flush and prepare surfaces
for welding.
10. Locate the Boom Pivot Plate Weldment (4) P/N
1001141633 to the pivot tower weldment (2). See
“Boom Pivot Plate Welding Locations” on page 3.
Tack into place.
11. Completely weld the boom pivot plates to the pivot
tower weldment using the recommended weld
material with types and sizes. See “Boom Pivot Plate
Welding Locations” on page 3.
12. Inspect welds using the magnetic particle or
dye-penetrant inspection methods to assure there
are no cracks or deformities. If any cracks or
deformities exist, grind to remove affected area(s)
and repeat the weld and inspection procedures.
13. Remove the three retaining bars (5) connecting the
two pivot plates.
14. Clean, prime and paint the affected areas.
Note: Refer to Service Manual 31200353, Section 3.4.8
for detailed boom assembly installation.
15. Properly connect the battery.
16. Verify the proper operation of all boom functions
through a minimum of five cycles.
17. Inspect the repair areas for discrepancies. Contact
JLG Safety 1-877-554-7233 (877-JLG-SAFE) for
further evaluation if any discrepancies are found.
18. Close and secure the engine covers.
19. Remove the Do Not Operate Tags from both the
ignition key switch and the steering wheel.
20. Return machine to service.
NOTICE
Do not damage the parent metal during this procedure.
MH7000
2
1
MH7020
3
MH7010
5
2
5
5
4
3
31200804
SkyTrak Boom Pivot Repair Instructions For Kit 1001141603
1.8 BOOM PIVOT PLATE WELDING LOCATIONS
A. 5.220 - 5.340 in (134,1 - 135,6 mm)
B. 20.320 - 20.440 in (516,1 - 519,1 mm)
C. 2.180 in (55,3 mm)
D. 16.270 in (413,2 mm)
2X
0.50
0.50
A
B
D
C
MH7030
4 31200804
SkyTrak Boom Pivot Repair Instructions For Kit 1001141603
This Page Intentionally Left Blank
Otros manuales de Elevador de pluma de JLG
JLG
JLG 1230ES Manual de uso y cuidado
JLG
JLG 0200230092 Manual de uso y cuidado
JLG
JLG H340AJ Manual de uso y cuidado
JLG
JLG 100SX Manual de instrucciones
JLG
JLG E600 Manual de uso y cuidado
JLG
JLG 1500AJP Manual de uso y cuidado
JLG
JLG 600SJC Guía de instalación y uso
JLG
JLG 3507 Manual de usuario
JLG
JLG K13 Manual de instrucciones
JLG
JLG 3369LE Manual de uso y cuidado
JLG
JLG 600A Guía de instalación y uso
JLG
JLG E300A Manual de uso y cuidado
JLG
JLG EC450AJ Manual de uso y cuidado
JLG
JLG 3369LE Manual de usuario
JLG
JLG 800AJ HC3 Manual de uso y cuidado
JLG
JLG TOUCAN 10E Guía de instalación y uso
JLG
JLG TOUCAN 1010 Manual de usuario
JLG
JLG 340AJ Guía de instalación y uso
JLG
JLG Power Towers Nano Instrucciones de funcionamiento
JLG
JLG 1200SJP Manual de uso y cuidado
Manuales populares de Elevador de pluma de otras marcas
Skyjack
Skyjack SJ 46AJ Manual de usuario
Molift
Molift Quick Raiser 205 Manual de usuario
Snorkel
Snorkel SL26RTE Guía de inicio rápido
Terex
Terex Genie Z-135/70 Manual de instalación y funcionamiento
Terex
Terex Genie ZX-135/70 Manual de instalación y funcionamiento
Oshkosh Corporation
Oshkosh Corporation JLG E300A Manual de usuario