JL Audio Stealthbox SB-J-LBRTY/12W3 Manual de usuario

➔

Stealthbox®

INSTALLATION GUIDE

SB-J-LBRTY/12W3, JL AUDIO, Inc 2003 Sheet SKU#011168 Revision4/9/2003Page 1

for the

SB-J-LBRTY/12W3

(Freedom,Limited,Renegade,Sport)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Open the rear door and remove

any contents and the retractable security

cover.

STEP 2:

The enclsoure will be mounted on

the driver’s side cargo area. Both cleats are to

be removed.

STEP 3:

To remove both cleats, you need to

remove both of the OEM rivets.

STEP 4:

With a 1/4” drill bit, drill out the

rivet’s head.Then with a punch out and ham-

mer, carfully tap out the rivet’s body.

STEP 5:

After the rivets are completely

removed, the cleats should pull up.They are still

going to be attached to the carpet.

STEP 6:

Unasnp the cleats to remove them

from the carpet.

*WARNING*

Please keep these cleats with the vehicle’s

owner.They will need to be reinstalled if they

remove the Stealthbox.

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

➔➔

➔➔➔

STEP 7:

You will need a tape measure and a

marker or pencil for this step.

Rear Cleat Location: Spread the carpet.

Find the center between the two holes, then

measure 1/2” out from the center to the out-

side of vehicle.Then mark.

STEP 11: With the supplied four rivets, rivet into

the exposed holes from the drilled out OEM rivets

from STEP?

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8:

Front Cleat Location: Spread

the carpet. Find the center between the two

holes, then measure 1/2” out from the holes

to the middle of vehicle.Then mark.

STEP 12: Hand thread the two supplied socket

cup set screws into the bottom of the Stealthbox,

leaving about 1” of each threaded rod exposed.

Make sure that the slotted end is exposed.

Place the Stealthbox into the mounting location. Be

careful guiding the threaded rods through the 1/2”

drilled holes.(If you’re not careful you will damage

the threads).

➔

STEP 13: With the Stealthbox in place and a sec-

ond person pushing down, it is time to mount the

Stealthbox into place.

Double check the socket cup set screws for proper

exposed length outside of the vehicle. Use a large flat

blade screw driver to adjust the threaded rod length.

The front threaded rod is not going to be easy to

access.There is a fast simple way and a more time

consuming way, please pick. Please read STEP 13(a)

and STEP 13(b) before mounting the Stealthbox

Enclsoure.

STEP 13(a): This is the fast simple way. Gather up

one supplied 3/8” hex nut, one supplied 3/8” lock

washer and one supplied 3/8” fender washer.

Place the hex nut into a 3/8” drive short socket(long

socket used in picture), dab a little dum-dum or hot

glue to the rim of the socket, place a supplied 3/8”

lock washer onto the socket, dab a little dum-dum

or hot glue to the rim of the 3/8” lock washer, then

place a supplied 3/8” fender washer on top. Make

sure that all middle holes of the mounting harware

line up. Carefully guide the mounting hardware and

the socket to the front exposed threaded rod.

STEP 9: With 1/2” drill bit and drill. Drill at the

marked locations from STEP 7 & STEP8

*CAUTION*

Before drilling make sure that you are not going to

be driling into gas lines, gas tank, brake lines, eletrical

wiring and what ever else that might cause a bad

day.

STEP 10: This is what your 1/2” drilled hole is

going to look like.This is the front cleat location.

SB-J-LBRTY/12W3 JL AUDIO, Inc 2003 Sheet SKU#011168 Revision4/9/2003Page 2

www.jlaudio.com

➔

Specifications:

Enclosure Type: Acoustic Suspension (Sealed)

Driver Type: One 12W3v2-D2 Subwoofer

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:

(2) 3/8”-16x2 1/4”Socket Cup Set Screws

(2) 3/8” x 1 1/4” Fender Washer

(2) 3/8” Split Lock Washer

(2) 3/8” Hex Nut

(4) Rivets

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.

Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔➔

STEP 13(b): This is the more time consuming,

but easier way to access the front exposed threaded

rod.You need to unbolt the over flow gas can. Please

make sure that you are careful and you do not tip

over this plastic tank. Do not do this while smoking.

The three arrows show the three mounting nuts

that have to be removed. Unbolt and carefully sup-

port this palstic tank.

After the tank is supported, place a supplied

3/8”fender washer, a supplied 3/8” lock washer then

a supplied3/8” hex nut in this order onto the thread-

ed rod.Thighten.

STEP 14: The rear exposed socket cup set screw

is a lot easier to excess. Place a supplied 3/8” fender

washer, a supplied 3/8” lock washer then a supplied

3/8” hex nut in this order onto thesocket cup set

screw.Thighten.

➔

SB-J-LBRTY/12W3, JL AUDIO, Inc 2003 Sheet SKU#011168 Revision4/9/2003Page 3

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

VR650-CSi

TR650-CXi

Front Location OEM’s Driver Size:

6 3/4” (171.45mm)

Applicable JL Audio Products:

TR,VR,XR 650-CXi,CSi

Rear Location OEM’s Driver Size:

6 3/4” (171.45mm)

Applicable JL Audio Products:

TR,VR,XR 650-CXi

Cont.

From

Page

STEP 15: With the Stealthbox properly mounted,

run speaker wire to the Stealthbox’s terminal cup.

Wire it up.

Double check for proper functioning of the woofer

at this time.

➔

Difficulty Of Installation:

Este manual sirve para los siguientes modelos

Otros manuales de Subwoofer de JL Audio

JL Audio

JL Audio 94643 Manual de usuario

JL Audio

JL Audio 13W1v2-4 Manual de usuario

JL Audio

JL Audio gotham v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-CAM/10W3v3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-SLVCNSL/10W3-D6 Manual de usuario

JL Audio

JL Audio 10TW3-D8 Manual de usuario

JL Audio

JL Audio Stealthbox SB-F-SUPRCC/13TW5v2 Manual de usuario

JL Audio

JL Audio SB-N-ALT/10W3v3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-J-GCHER3/10W1v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-SLVEXT/12W3 Manual de usuario

JL Audio

JL Audio JL AUDIO Evolution ZR800-CW Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-HUMR2/12W6v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-H-PIO1K/10TW3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK Manual de usuario

JL Audio

JL Audio Stealthbox SB-T-TUNDC/8W7 Manual de usuario

JL Audio

JL Audio Stealthbox SB-H-S2000/10W3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-ESCESV/10W1v3 Manual de usuario

JL Audio

JL Audio 12W3v3-2 Manual de usuario

JL Audio

JL Audio MX101B3-SG Manual de usuario

JL Audio

JL Audio 300/2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-S-IMPRZA/10W6v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-SC-XBG1/10W1v2 Manual de usuario

JL Audio

JL Audio ACP1 08LG-W3v3 Manual de usuario

JL Audio

JL Audio 12WOv3-4 Manual de usuario

Manuales populares de Subwoofer de otras marcas

Sony

Sony XS-AW8 Manual de usuario

Sony

Sony XS-L836 Manual de usuario

B&C Speakers

B&C Speakers 15 HPL 76W Manual de usuario

Velodyne

Velodyne DD-18+ Manual de usuario

Sonance

Sonance Cinema Series SUB 10-150 Manual de usuario

Hifonics

Hifonics HW-12 Guía de inicio rápido

Magnat Audio

Magnat Audio ADR 130 BP Manual de usuario

Blitz

Blitz BZP106 Manual de usuario

Technics

Technics SB-AS500 Manual de usuario

Lyngdorf

Lyngdorf BW-2 Manual de usuario

Lyngdorf

Lyngdorf BW-3 Manual de usuario

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manual de usuario

REL Acoustics

REL Acoustics Q Series Manual de usuario

Pioneer

Pioneer Elite S-W1EX Manual de usuario

L-Acoustics

L-Acoustics KIVA SB15M Guía de inicio rápido

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manual de usuario

KEF

KEF KUBE 200 Manual de usuario

Yamaha

Yamaha SW500 Manual de usuario