JL Audio 94657 Manual de usuario

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the Stealthbox®be properly mounted to the vehicle

according to these instructions. Failure to mount the enclosure

properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

DIFFICULTY:

ESTIMATED TIME:

12 HOURS

Continued on Next Page

OUT

SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502

INSTALLATION GUIDE

for the

SB-POL-GNRLSPKR/MX650

SKU# 94657

2016 & Up Polaris General

Enclosure Type: Sealed

Driver Type: MX650-CCX-SG-TLD-B

Nominal Impedance: 4 ohms

Continuous Power Handling: 60 watts (RMS method)

INCLUDED HARDWARE / WIRING INFORMATION

Continued on Next Page

Page 2 • JL Audio, Inc., 2017

SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502

Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

(hardware pictured for one)

Wire Size Wire Color Use

16 AWG Red/Stripe Speaker Positive (+)

Black/Stripe Speaker Negative (-)

20 AWG

Red Not Used

Green Not Used

Blue LED Positive (+)

Yellow LED Negative (-)

BOM ID Qty SKU Description

1 2 152414 Wire Harness (10’)

2 2 153729 1/4 - 20 x 1” Serrated Flange Head Bolt

3 2 153817 1/4” Stainless Steel Flat Washer

4 2 153815 1/4 - 20 Nylon Insert Locknut

- 1 150778 Fuse & Fuse Holder Kit (not shown)

- 1 150249 Foam Tape (not shown)

LED Wire Connections

• For short-circuit protection, install a supplied fuse holder onto EACH

speaker’s BLUE (+12V) LED power connection lead.

• Connect all BLUE (+12V) leads together (parallel) and connect to a

switched +12V supply. Connect all YELLOW (GRD) leads together and

connect to a negative ground or to the NEGATIVE battery post.

• We recommend activating the speakers’ LEDs thru a lighting circuit that

supplies +12V via an existing switch. If an existing switched circuit is

not available, you may install a dedicated toggle/rocker style switch that

will supply positive (+12V) power. Fuse this connection according to how

many LED circuits you have (LED circuits x 150A).

[GND]

LED

[+12V]

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

LED

Fuse

[GND]

[+12V]

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

LED

Fuse

Diagram shows one speaker pair of

LED circuits connected in parallel.

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio MX280/4. The diagram below shows the recommended crossover settings for the MX280/4. For a detailed description of the ampli-

er settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2017

SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502

Page 4 • JL Audio, Inc., 2017 Continued on Next Page

STEP 8

From the outside of the vehicle, slide a 1/4” Flat

Washer and 1/4 - 20 Nylon Insert Locknut over

each of the 1/4 - 20 x 1” Serrated Flange Head

Bolts, and hand tighten.

STEP 7

Slide a 1/4” Flat Washer over each of two 1/4

- 20 x 1” Serrated Flange Head Bolts. Pass an

assembly through each of the two indicated

holes in the enclosure and through the plastic

panel to the outside of the vehicle.

STEP 6

Pass the cable exiting the enclosure through

the larger hole in the plastic panel. Position the

speaker enclosure flush against the kick panel,

allowing the grommet to sit in the drilled hole.

STEP 5

Pass the Wiring Harness into the enclosure

through the larger hole. Slide the Seal Nut

over the wiring, thread it over the pre-installed

Liquid Tight Wire Seal, and fully tighten.

STEP 4

Using a 1/4” drill bit, carefully drill through the

center of each of the marks made in the

previous step.

Using a 1-1/8” hole saw, enlarge only the hole

for the larger mark.

Remove the masking from the plastic panel.

STEP 3

Mark the location of each of the four holes in

the speaker enclosure onto the masked panel.

Note that one of the holes is larger than the

other three.

Remove the speaker enclosure from the

vehicle.

STEP 2

Place the speaker enclosure into position, flush

against the kick panel, as shown.

STEP 1

The following steps show the installation

procedure for the driver’s side only, but the

procedure is the same for both sides.

Empty the driver’s side of the vehicle, and

mask the plastic panel in the kick panel area, as

shown.

SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502

Page 5 • JL Audio, Inc., 2017

RECOMMENDED SUBWOOFER SOLUTIONS

The SB-POL-GNRL/10TW3 Stealthbox® subwoofer enclosure is also available for your vehicle. The weatherproof

enclosure is designed for a perfect t and houses a premium JL Audio subwoofer.

SB-POL-GNRL/10TW3

SKU# 94656

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502

STEP 10

Slide a 1/4” Flat Washer and 1/4 - 20 Nylon

Insert Locknut over the 1/4 - 20 x 1” Serrated

Flange Head Bolt, and fully tighten all three

sets of hardware.

Route the cable as necessary. Refer to Page 2

for wiring information.

STEP 9

Slide a 1/4” Flat Washer over a 1/4 - 20 x 1”

Serrated Flange Head Bolt, and pass the

assembly through the indicated hole in the

plastic panel and into the enclosure.

ST E P 11

Connect and install the speaker. Remove the

adhesive backing, and install the JL Audio logo

badge.

Repeat the process for the passenger side.

Note: For optimum performance, we

recommend applying the included Foam Strips

(or sound damping material) to surrounding

plastic panels to reduce unwanted vibrations.

All specifications are subject to change without notice. “JL Audio®”and “How we play®” are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo are trademarks

of JL Audio, Inc.

(954) 443-1100

www.jlaudio.com

JLA-SKU# 011502 • ver. 12.05.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

Este manual sirve para los siguientes modelos

Otros manuales de Subwoofer de JL Audio

JL Audio

JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3 Manual de usuario

JL Audio

JL Audio 12W4-4 Manual de usuario

JL Audio

JL Audio Stealthbox SB-M-3-SPD/10W3v3 Manual de usuario

JL Audio

JL Audio 10TW1-2 Manual de usuario

JL Audio

JL Audio Fathom IWS-SYS-2 Manual de usuario

JL Audio

JL Audio 10W6v2-D4 Manual de usuario

JL Audio

JL Audio Stealthbox 011180 Manual de usuario

JL Audio

JL Audio 8W3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-N-ARMAD/10W6v2 Manual de usuario

JL Audio

JL Audio 12W6v3 Manual de usuario

JL Audio

JL Audio 94350 Manual de usuario

JL Audio

JL Audio Stealthbox SB-J-UNLTD4DR/13TW5v2 Manual de usuario

JL Audio

JL Audio fathom v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-SC-XB/10W3v3-4 Manual de usuario

JL Audio

JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v2 Manual de usuario

JL Audio

JL Audio Fathom IWSv2-SYS-113 Manual de usuario

JL Audio

JL Audio Stealthbox SB-SC-XBG1/10W1v2 Manual de usuario

JL Audio

JL Audio 12TW1-4 Manual de usuario

JL Audio

JL Audio Stealthbox SB-B-X5/10W1v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-N-FRNTCC/10W1v2 Manual de usuario

JL Audio

JL Audio M10IB5 Manual de usuario

JL Audio

JL Audio 6W3v3-4 Manual de usuario

JL Audio

JL Audio 10IB4 Manual de usuario

Manuales populares de Subwoofer de otras marcas

Sony

Sony XS-AW8 Manual de usuario

Sony

Sony XS-L836 Manual de usuario

B&C Speakers

B&C Speakers 15 HPL 76W Manual de usuario

Velodyne

Velodyne DD-18+ Manual de usuario

Sonance

Sonance Cinema Series SUB 10-150 Manual de usuario

Hifonics

Hifonics HW-12 Guía de inicio rápido

Magnat Audio

Magnat Audio ADR 130 BP Manual de usuario

Blitz

Blitz BZP106 Manual de usuario

Technics

Technics SB-AS500 Manual de usuario

Lyngdorf

Lyngdorf BW-2 Manual de usuario

Lyngdorf

Lyngdorf BW-3 Manual de usuario

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manual de usuario

REL Acoustics

REL Acoustics Q Series Manual de usuario

Pioneer

Pioneer Elite S-W1EX Manual de usuario

L-Acoustics

L-Acoustics KIVA SB15M Guía de inicio rápido

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manual de usuario

KEF

KEF KUBE 200 Manual de usuario

Yamaha

Yamaha SW500 Manual de usuario