Jetmaster Al Fresco Manual de usuario
JETMASTER OUTDOOR QUADRO AL FRESCO WOOD FIRE
INSTALLATION INSTRUCTIONS
(A product of the REPUBLIC of SOUTH AFRICA)
ALL INSTRUCTIONS TO COMPLY WITH AS/NZS2918:2001
The Al Fresco outdoor wood re is a combined outdoor entertainment and cooking appliance utilising
4 unique features in one unit – A BBQ grill and hotplate, a Potjie Pot for slow cook stews, a Pizza oven
and a re for outdoor entertainment heating once cooking is completed.
IMPORTANT: Read all instructions carefully before starting installation.
Failure to follow these instructions may result in a re hazard and will void any warranty.
Head Oce & Showroom
12 Tawari St, Mt Eden, Auckland
Ph: 09 623 6996
thereplace.co.nz
HEBEL HEAT CELL ASSEMBLY
Fig 1.3.1
Fig 1.3.2 Fig 1.3.3
C
E
50
D
A
A1
A2
B1
Y
F
A A1 A2 B B1 C D E F Y
1050 1150 1100 502 530 850 300/400 240 800 350
Table 1.0 (all dimensions in millimetres)
HEBEL HEAT CELL CUTTING SCHEDULE
No.1 Base 1 off: 1410mm x 733mm = 1.033m²
No.2 Sides 2 off: 1225mm x 733mm = 1.796m²
No.3 Rear 1 off: 1260mm x 1225mm = 1.544m²
No.4 Front Top Outer 1 off: 300mm x 1260mm = 0.378m²
No.5 Front Top Inner 1 off: 400mm x 1260mm = 0.504m²
No.6 Front Side 2 off: 825mm x 75mm = 0.124m²
Total = 5.378m²
2400mm x 600mm x 75mm Panel = 4 Reqd
1200mm x 600mm 75mm = 8 Reqd
D
Fig 1.1
REAR FRONT
QUADRO FIREBOX
B
FIREBOX INSTALLATION PREPARATION
The Hebel Heat Cell shown in Fig 1.1 is constructed from 75mm (centrally reinforced) Hebel panels and is a
standalone construction required within a false timber framed chimney chase incorporating a ue system.
The Hebel Heat Cell may be substituted with 150 or 200 series Masonry blocks or similar, provided the
internal dimensions and details of the heat cell are the same as those shown in Fig 1.1
If the Quadro rebox is to be positioned inside a timber frame out, the following MUST be observed;
1. The Quadro MUST be installed so that it is positioned inside a Hebel Heat Cell as per Fig 1.1
2. The Hebel base may be positioned directly onto a timber oor. Please note that the rebox is positioned
onto 50mm high non-combustible spacers inside the Hebel Heat Cell and 100mm dia. (x2 ) inlet air
vents are located down as low as possible in the rear heat cell panel (panel 3). The inlet air vents must
vent to the outside and be vermin and bird proof.
3. The hearth/oor protector where located onto a combustible oor surface, must be made from 100mm
concrete or 75mm Hebel (preferred) and extend a minimum of 600mm in front of the rebox and
200mm to each side of the rebox opening. Refer to Fig 2.1 The hearth/oor protector nished top
surface should align to the same level as the lower front edge of the rebox fascia frame. Refer to Fig
2.2
4. There MUST be 25mm minimum air spacing between the Hebel Heat Cell and any timber frame out on
the sides and rear panels. Timber framing may touch the top of the Hebel Heat Cell. There must be a
minimum of 25mm clearance from the ue to any combustible material.
5. When nishing the front presentation, DO NOT place any combustible materials above the front of the
re within 400mm above the rebox.
6. The rebox must be restrained with earthquake restraints by drilling holes in the base of the back
corners of the rebox using 6mm dynabolts or similar. Do not over-tighten and deform the rebox and
also ensure the BBQ grill and plates are not compromised when stored in the storage slot under the
logpan.
7. A purpose made SS weather cover with lockable handles is also available to protect the rebox inner
when not in use.
Fig 2.1
Fig 2.2
CHIMNEY CHASE AIR VENTILATION
50 25
25
120mm
minimum
Drip
Line
Spigot flashing to suit
flue pipe casing
120mm
minimum
Oversized casing cover
is necessary
Drip
Line
Air
Vent
Air Ventilation Through Chimney Chase Air Ventilation Through Top Flashing
Fig 5.0 Fig 6.0
Non combustible
material: 75mm
Hebel Block or
12mm Supalux or
12mm Eterpan LD
NOTE: Air vents to be min 2 x 80mm diametre or
equal square or rectangular shaped area. These
must be bird & rodent proofed with permanently
xed screens.
FLUE INSTALLATION
1. Install rst length of ue pipe crimped end down, inside gather collar. Rivet ue pipe in 3 places around
gather collar. Place bottom ue spider bracket around gather ue pipe collar, secure in position by
tightening up coach bolt/screw (supplied).
2. Install second length of the ue pipe crimped end down and x by riveting in at least 3 places around
the ue pipe joint.
3. Install rst length of the ue pipe casing by positioning on installed bottom ue spider bracket crimped
end up.
4. Position ue spacer at the ue pipe joint.
5. Repeat steps 1 - 4 to the required ue system height.
6. The last length of ue pipe needs to extend past the ue pipe casing by at least 150mm or ush with
the top of the casing cover spigot when tted - sizing/measuring and cutting down should be carried
out prior to the ue pipe casing being tted over the ue pipe.
7. Before tting casing cover, place the spider in opposition with the spider post facing down between the
ue pipe and ue pipe casing. Secure spider in position. Place the casing cover over the ue pipe, press
down rmly onto the spider. Check airway around the casing cover is clear, then secure in position using
three stainless steel rivets.
8. Fit cowl to top of ue - DO NOT RIVET IN POSITION. In high wind areas, it is recommended that the cowl
be secured in position with a stainless steel self tapping screw, this will enable the cowl to be removed
for cleaning. Discuss Bird Proong needs with your installer. N.B. in extreme wind areas it may be
necessary to consult The Fireplace Ltd or your local agent for further technical assistance.
9. If ue is concealed in a chase, allow for air vents (2 x 80mm diam. or equivalent) at the highest
possible point on the chimney chase or alternatively, allow a min 25mm air space between the casing
cover spigot and the outer casing. Refer to Figure 5 & 6.
GENERAL MAINTENANCE
• When the re is not in use, ensure the stainless steel cover is tted at all times. This will assist in
protecting the rebox. DO NOT attach the cover when the re is in use.
• This re is NOT warranted against rust or salt air corrosion. Please refer to the Fireplace Fireguard
Warranty for full details.
• A seasonal touch-up is recommended. Simply remove surface rust with some steel wool and repaint
using Black VHT paint (available from your nearest showroom). Please ensure all areas around the
rebox are protected when re-painting.
For high wind locations, The Fireplace recommends tting a Stainless Steel Jetmaster Bird Cowl
Tabla de contenidos
Otros manuales de Chimenea de interior de Jetmaster
Jetmaster
Jetmaster MK6 Instrucciones de funcionamiento
Jetmaster
Jetmaster Standard 16 Manual de usuario
Jetmaster
Jetmaster Universal 500 Manual
Jetmaster
Jetmaster QUADRO 1050 Manual de usuario
Jetmaster
Jetmaster MYNX Manual de usuario
Jetmaster
Jetmaster Open Wood Fire Manual de usuario
Jetmaster
Jetmaster 700 Instrucciones de instalación
Jetmaster
Jetmaster SLOW COMBUSTION Manual de usuario
Jetmaster
Jetmaster DROP IN 1020 Manual de usuario
Jetmaster
Jetmaster GF1016 Manual de usuario
Jetmaster
Jetmaster 400 Manual
Jetmaster
Jetmaster UNIVERSAL 440 Instrucciones de instalación
Jetmaster
Jetmaster UNIVERSAL Instrucciones de instalación
Jetmaster
Jetmaster HEAT & GLO MEZZO-AU Manual de usuario
Jetmaster
Jetmaster 1200 series Instrucciones de instalación
Jetmaster
Jetmaster UNIVERSAL 440 Manual de usuario
Jetmaster
Jetmaster Universal 500 Manual de usuario
Jetmaster
Jetmaster kemlan supernova rf insert Manual
Jetmaster
Jetmaster 700 Vent Free Built in Manual de usuario
Jetmaster
Jetmaster INSET STOVE MKIII 16i Manual del propietario
