JERRY'S ARTARAMA Saint Remy Manual de usuario

Car fully r ad through all instructions

b for proc ding.

Multi-Angl Wood

Studio Eas l

www.jerrysartarama.com I 800.827.8478

Guid to Ass mbly

The Sai t Remy Multi-A gle Wood Studio Easel allows

you to pai t a d var ish eve the largest ca vas. If you

pai t small you ca actually pai t two ca vases side by

side — eve of differe t heights! It is made of smoothly

sa ded, oiled Beech wood a d is superbly crafted to

fu ctio flawlessly. It's wide mast allows you to pai t

pictures up to 60" wide a d 82" high ... plus you ca

pai t at a y a gle — eve flat — maki g it the perfect

support for art i most media!

Maximum h ight: 114 inch s

Minimum h ight: 78 inch s

Bas : 31.5 in. W×30.25 in. D

W ight: 43 lbs.

(4) Brass

Pressure Plates

Part 1 (2)

H1 H2 H3

Part 6 (1)Castors (4)

Part 2 (2)

Part 3 (2)

Part 5 (1)

Part 4 (2) & 12 (2)

Part 7 (2) Part 8 (1)

Hardwar Packs*

Be sure to read through and understand all instructions before proceeding.

Carefully check the contents of the box to ensure all parts are included.

Parts*

Pack A: (4) 2 ½" bolts, (4)³/8" barr l nuts

Pack B: (16) 5/8" woodscr ws

Pack C: (2)2½" bolts, (2)³/8" barr l nuts

Pack D: (8) 1" woodscr ws

Pack E: (2) ratch t syst ms, (8)woodscr ws

Pack F: (4)2½"bolts, (4)³/8" barr l nuts

Pack G: (2)1

7/8" wood wash rs, (2) 5/8"

brass wash rs, (2) black plastic turn knobs,

(2)3"bolts

Pack H1: (2) 5/8"brass wash rs,

(2)1¾"bolts, (2)black plastic turn knobs

Pack H2: (2) 5/8"brass wash rs,

(2)2¼"bolts, (2) black plastic turn knobs

Pack H3: (2)5/8" brass wash rs, (2)5"bolts,

(2)black plastic turn knobs

Pack I: 17/8"bolts, h x wr nch

Pack J: (4) black plastic turn knobs (short)

(2) black plastic turn knobs (long)

Part 9 (2)

Part 10 (2) & 11 (2)

Part 13 (2) Base Blocks (2) *Hardware & Parts not to scale

Scr wdriv rs Includ d

STEP 6

You will n d: Pack A, Part 1, Part 2

STEP 2

STEP 3

You will n d: Pack C, Part 3, Base Assembly (step 1 & 2), Screwdriver

STEP 4

STEP 5

STEP 1

Ass mbly Instructions

Ass mbl th wood n parts as th picur shows and s cur using th hardwar from

Pack A. Th barr l nuts will b plac d into th bottom of Part 2 whil th bolts will b

ins rt d through th sid s of Part 1.Tight n th bolts into th barr l nuts.

Ins rt Part 3 into th top of th bas as shown in St p 3a. S cur to th base by

placing th barr l nut into th inn r sid of ach Part 3. Ins rt th bolt through th

bottom of th bas and tight n into th barr l nut as shown in St p 3b. R p at for

additional sid .

You will n d: Pack F, Part 6, Part 7, Part 8, Part 9, Screwdriver

Ins rt both Part 7 pi c s into th bottom of Part 6. Slid Part 8 onto th bottom of both

Part 7 pi c s. Tak both Part 9 boards and plac on th sid s of Part 6 and Part 7 as

shown. S cur th s by sliding th barr l nuts into th back sid of Part 6 and Part 7.

Ins rt th bolts through th sid s of Part 9 and tight n th bolts into th barr l nuts.

You will n d: Pack B, Castors, Base Assembly (Step 1), Screwdriver

You will n d: Pack D, Pack E, Part 4, Part 5, Screwdriver

You will n d: Pack G, Pack H1, Pack H2, Pack H3, Part 10, Part 11

You will also n d: Completed Base (Step 3), Canvas Support/Center asts (Step 4),

and th H Frame (Step 5)

Attach Part 4 to th back of Part 5 using (4)1"woodscr ws from Pack D(8 total) in

th pr -drill d guid hol s. R p at. Us th woodscr ws from Pack E to attach th (2)

ratch t syst ms to th bottom of Part 5 using th pr -drill d hol s.

Part 2 (2)

Part 3 (2)

Part 4 (2)Part 5 (1)

Part 9 (2)

Part 8 (1) Part 11 (2) Inside

Part 10 (2)

Outside

Part 7 (2)

Part 6 (1)

Pack C

Pack D

Pack G Pack H1 Pack H3

Pack H2

Pack F

Pack E

Castors (4)

Part 1 (2)

Connect here and

Connect here

Base

Assembly

(Step 1)

Pack B (16)

Pack a

Step 3a

Back View

F ont

View

Canvas Suppo t

& Cente Masts Bottom

of Pa t 5

Step 3b

Completed Base

(Step 3)

Completed Base

(Step 3)

H F ame

(Step 5)

H F ame

(Step 5)

Connect here

Canvas Suppo t

Cente Masts

(Step 4)

INSTRUCTIONS CONTINUED ON BACK PAGE

Using th suppli d Phillips scr wdriv r, turn th Base Assembly ov r and attach th

(4) castors with th (16) 5/8" woodscr ws from Pack B in th pr -drill d guid

hol s. Th r will b 4 woodscr ws for ach castor.

STEP 6 (Continu d)

STEP 7

Attach th H Frame b tw n th two uprights (Part 3/St p 3) of th Base. Whil holding

fram in plac , put th two bolts through th uprights and into th H Frame (St p 5).

Add th wood n wash rs in b tw n th upright and th H Frame as shown in Step

6a. Onc th bolt is through th H Frame, add th brass wash rs and tight n th black

plastic knob until s cur as shown in Step 6b.

Attach (1) Part 11 to th insid of th H Frame

n ar th upp r crossbar (Part 6 in St p 5). Ins rt

(1) bolt from Pack H2 through th pr -drill d

hol s in Part 11. Add th wash r, th n th knob

on th outsid of th H Frame. R p at for th

oth r sid .

Slid (1) Part 10 around th attach d Part 11

and s cur with bolt from Pack H1 on th

outsid . Add th wash r, th n th knob on th

insid of Part 11. R p at for th oth r sid .

Attach Part 10 to th Base using Pack H3 with

th knob on th outsid of th Base. R p at for

th oth r sid . All instructions are shown in

Step 6c Back View.

Step 6a Step 6b

Step 6c

Step 6d

Back View

Bottom

Canvas Suppo t

Top

Part 11

Part 10

Grooves

Part 6

Pack H2 (1)

Pack H1 (1) Part 11

slides

inside

Part 10

Pack

H2 (1)

Pack

H1 (1)

Pack

H3 (1)

Pack

H3 (1)

You will n d: Pack I, Pack J, Base Blocks, Part 12, Part 13

Part 12 (2)

Part 13 (2)

Pack I

Base Blocks (2)

Pack J

Onc compl t , tilt th as l

and slid th Canvas Support

/Center ast (Step 4) onto th

th H Frame from th bottom

cross bar (Part 8 in St p 5) into

th groov s in th upp r

crossbar (Part 6 St p 5) as

shown in Step 6d.

Attach th Base Blocks using Pack I to s cur th Base Uprights

(Step 3/Part 3) as shown in Step 7a.

Plac (2) Brass Pressure Plates into th hol s insid th groov of

Center ast as shown in Step 7b and slid both Part 12s onto th

two Center asts. S cur with (1) Long knob and (1) Short knob on

both sid s as also shown in Step 7b. Slid Part 13 onto ach Part 12.

Plac th ﬁnal (2) Brass Pressure Plates into th hol s on th back of

Part 13 and s cur Part 13 into Part 12 with th ﬁnal (2) Short knobs

as shown in Step 7c.

R vi w th plac m nt of knobs in Front View and Back View photos.

Short knobs

Long knobs

Short knobs

Brass Plates

Step 7a

Step 7b F ont View

Back View

Step 7b

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual