Jensen MPR419Q Instrucciones de funcionamiento
MPR419Q
MECHLESS MEDIA RECEIVER
AM-FM
USB Media Player
Bluetooth Music & Hands-Free Calling
Motorized Phone Mount
with Wireless Charging
INSTALLATION &
OWNER’S MANUAL
OPERATIONMPR419Q
2
2
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for
instructions.
• Avoid installing the unit where it would be subject to high temperatures,
such as from direct sunlight, or where it would be subject to dust, dirt or
excessive vibration.
Step 3:
Connect all wiring
harnesses and slide
the head unit into the
mounting sleeve until
it clicks into place.
Step 1:
Insert the mounting
sleeve into the
installation kit or
dashboard.
Step 2:
Bend multiple
mounting tabs around
the mounting sleeve
until the mounting
sleeve is secure.
Mounting the Head Unit:
T
ypical DIN mounting
Mounting Sleeve
Dashboard or
Installation Kit
Single DIN
Mounting Sleeve
Dashboard or Installation Kit
Mounting Tabs
Single DIN
Mounting Sleeve
Dashboard or Installation Kit
Head Unit
Single DIN
3
3
OPERATIONMPR419Q
Wiring DIagram
Tips
When replacing a fuse, make sure to use the correct type and amperage.
Using an incorrect fuse could cause damage. The unit uses (1) 10 amp ATC
fuse located on the wiring harness.
IGNITION / ACC 12V(+) RED
BATTERY 12V (+) YELLOW
CHASSIS GROUND (-) BLACK
REMOTE TURN-ON(+)
POWER ANTENNA (+) DARK BLUE
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
GREEN
GREEN/BLACK
VIOLET
VIOLET/BLACK
FRONT LEFT SPEAKER
FRONT RIGHT SPEAKER
REAR LEFT SPEAKER
REAR RIGHT SPEAKER
OPERATIONMPR419Q
4
4
Control Locations - Front Panel
Power / Mute
Voice Control
Open
End Call
USB Port
Auxiliary Input
1
11
2
12
3
4
5
6
7
8
9
10
Preset 6 / Folder Up
Preset 5 / Folder Down
Preset 4 / Play / Pause
Preset 3 / Intro
Preset 2 / Random
Preset 1 / Repeat
Volume Up
1
2
3
4
5Tune/Track Down
Tune/Track Up
Mute
Volume Down
1
3
5
4
2
Control Locations - Remote Control
19
Band / Display
Mode
Volume / Menu
Tune/Track Up
Microphone
Tune/Track Down
13
14
15
16
17
18
19Reset
5
5
OPERATIONMPR419Q
Remote Control Preparation
Slide the remote into the steering wheel clip to
mount on the steering wheel for easy access
while driving. Steering Wheel Clip
1
2
3
Notes:
• The remote control uses one 3 volt Lithium CR2025 battery.
• Remove the battery if the remote will not be used for a month or longer.
• Remove and dispose of battery properly.
• Do not store battery with metallic objects or materials.
Remove the battery tape before
first use.
To install a new battery, remove
the battery cover and the old
battery, then insert the new
battery keeping the (+) side up.
Replace the battery cover to
secure.
OPERATIONMPR419Q
6
6
Wireless Charging Operation
To use the wireless charging pad, press OPEN on the front panel.and
the pad will automatically slide out from the unit. Once the pad is fully
extended, open the phone holder at the bottom. Place the phone on the
pad, and lift the buckle on the top of the pad to securely support the phone.
Note: Only supports phones with wireless charging feature.
After the phone enters charging mode, the LED status indicator will begin
to blue at the bottom of the pad. Normal charging mode will be indicated by
blue LED. If the foreign object is detected,the white LED will be blinking.
When charging is completed, the LED will remain solid blue.
When charging is complete, remove the phone and close the phone holder
at the bottom of the pad. Press OPEN to retract the pad. If the phone holder
on the pad is not closed, the charging pad will not retract.
Step #1
Press OPEN to open or close the
wireless charging pad.
Step #2
Open phone holder on the
bottom of the pad.
Note – Use the phone holder
on the top of the pad in order to
hold the smartphone more firmly.
Step #1
Press OPEN to open or close the
wireless charging pad.
Step #2
Open phone holder on the
bottom of the pad.
Note – Use the phone holder
on the top of the pad in order to
hold the smartphone more firmly.
LED Indication Standby FOD Charging Full Charge
Blue 2ႇ 2ႇ On On
White On Blinking 2ႇ 2ႇ
7
7
OPERATIONMPR419Q
Wireless Charging Operation
Step #3
Step #4
Place the smart phone on the wireless
charging pad to begin charging.
Note: LED Indicator for Charging Status
Charging: Flashing Blue
Fully Charged: Solid Blue
Press OPEN to close the wireless
charging pad.
Note: Before retracting the
charging pad, make sure to close
the phone holder. The pad will not
retract if the holder is open.
Step #3
Step #4 Press OPEN to close the wireless
charging pad.
Note: Before retracting the
charging pad, make sure to close
the phone holder. The pad will not
retract if the holder is open.
USB
USB
Step #5
For phones that do not support
wireless charging, insert the
charging cable that came with
your phone into the USB port
and place the phone on the
phone mount pad.
Safety Tip:
Please remove any pop sockets or cases the have a metal holding ring, as
this will prevent the charging pad from working and may damage the
device. Also, thick or metal cases will prevent the pad from charging the
phone or may cause the phone to overheat. Please use caution.
OPERATIONMPR419Q
8
8
General Operation
Press or any other button to turn the unit on.
Press and hold to turn the unit off.
Press MODE to select between Radio, USB, AUX and
Bluetooth. Current mode is shown in the display.
Adjust volume using the volume knob (00-40).
Press to silence the audio. Press again to
resume listening at the previous volume level.
Turning the volume knob also cancels mute function.
Insert a 3.5mm cable in the unit's front AUX port.
Press the RESET button to reset the unit back to the
factory settings if abnormal operation occurs. The
reset button is located on the front panel.
With the unit on, press and hold DISP to display
clock time. Press and hold DISP until the hours
begins to flash, then release. Rotate the volume
knob to adjust the hours. Press DISP, then rotate the
volume knob to adjust the minutes.
Press the volume knob momentarily to step through
and adjust the following audio functions, then rotate
the volume knob to adjust the desired function:
• Bass - Adjust -7 to 7.
• Treble - Adjust -7 to 7.
• Balance - Adjust L7 to R7 (L=R is equal balance).
• Fader - Adjust F7 to R7 (F=R is equal fader).
• Loudness - Turn the loudness feature ON or OFF.
• EQ - Select from a preset equalization curve, or
select User to set EQ manually.
Press and hold the volume knob to enter the setup
menu, then briefly press the volume knob to step
through menu options. Rotate the volume knob to
adjust the desired option.
• A-Store - Press DISP to automatically store
preset stations.
• Dimmer - Adjust the dimmer low (L) or high (H).
Beep - Turn the audible beep On or Off.
• Auto Answer - Select “ANSAUTO” to set the
unit to automatically answer incoming calls
via Bluetooth. Select “ANSMANU” to manually
answer incoming calls.
• Frequency Spacing - Select USA or Euro.
• Stereo/Mono - Select stereo or mono tuning.
• Local/Distance - Turn local tuning On or Off.
• Version - Displays the version number.
Power On/Off
Changing Modes
Volume
Mute
Auxiliary Input
Reset
Setting the Clock
Audio
Menu
9
9
OPERATIONMPR419Q
Tuner Operation
Press TUNE or TUNE to seek to the
previous or next strong station.
Press and hold TUNE or TUNE to enter
manual tuning mode, then press TUNE or TUNE
momentarily to change radio frequency up
or down one step at a time. Press and hold TUNE
or TUNE to return to seek tuning.
Press BAND to select between FM1, FM2, FM3,
AM1 and AM2 bands. Up to six presets can be
programmed for each band, enabling up to 18 FM
stations and 12 AM stations to be stored in memory.
Up to 18 FM and 12 AM stations can be stored. To
store a station, select the desired band and station.
Press and hold the desired preset button (1-6) for
more than two seconds. When stored, the preset
number will appear in the display.
Preset stations can be recalled any time by pressing
the corresponding preset button.
Press and hold MENU for more than 2 seconds,
When A-STORE appears, press DISP to store 18 FM
stations and 12 AM stations automatically.
Press PS to recall each preset staion that stored in
the memories in each band.
Note: This feature is only available with the Jensen
remote control app.
Seek Tuning
Manual Tuning
Band
Storing Presets
Recalling Presets
Automatically
Store
Preset Scan
Stations
OPERATIONMPR419Q
10
10
USB Operation
To play MP3 files, insert a USB device containing
MP3 files.
Press TUNE to skip to the beginning of the next
track. Press TUNE to skip to the beginning of
the previous track.
Press and hold TUNE or TUNE to fast
forward or reverse a track.
Press /
II
to temporarily stop USB playback.
Press /
II
again to resume playback.
Folders can be found by pressing Folder Up or
Folder Down. About one second after the folder
name is displayed, the first file under the selected
folder will be displayed and playback will begin.
Press RPT to toggle between RPT ALL and RPT ONE.
• RPT ALL - Plays all tracks on USB device.
• RPT ONE - Continuously repeats selected track.
Press RDM to play tracks in random order; press
again to cancel the RDM function.
Press INT to play the first 10 seconds of each track;
press again to cancel the INT function.
Playing MP3 Files
Track Select
Fast Forward
and Reverse
Pause
Folder Access
Repeat
Random
Intro
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Reproductor multimedia de Jensen
Jensen
Jensen SMPV-2GBUB Manual de usuario
Jensen
Jensen SMPV-2GBLB Manual de usuario
Jensen
Jensen SMPV-4GBUA Manual de usuario
Jensen
Jensen SMPV-4GBTA Manual de usuario
Jensen
Jensen CM9MIR Instrucciones de funcionamiento
Jensen
Jensen SMP-1GBEB Manual de usuario
Jensen
Jensen SMPV-4GBEB Manual de usuario
Jensen
Jensen SMP-2GBL - 2 GB Digital Audio Player Manual de usuario
