Jensen VM9114 Manual de usuario

VM9114

VM9114 Head Unit

Single DIN Sleeve

Wiring Harness

Parking Brake Sensor Extension Wire

Mounting Hardware

Cosmetic Trim Ring

3.5mm to 3.5mm Media Adaptor Cable

Owners Manual

Installation Guide

What’s in the Box

You will need these tools and supplies to install your VM9114:

• Torx type, ﬂat-head and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Tools and Supplies

Installation Guide

Instruccionnes de Instalación

Instructions d’installation

WARNING! Never install this unit where operation and viewing could interfere with safe driving

conditions.

Para obtener instrucciones en Español, diríjase a la página 5. Pour des instructions en Francais, référez-vous à la page 9.

EJECT

A/V

INPUT

VM9114

160 Watts

Multimedia Receiver

TAB

DASHBOARD

TAB

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to in-

stallation.

NOTE: If the VM9114 is to be installed in a car equipped with an on-board drive or navigation computer, do

not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these

conditions, use extra caution during installation to avoid causing a short circuit.

Pre-installation

Remove the four screws that attach the mounting sleeve to the

radio and remove the sleeve.

Install the mounting sleeve.

a. Install mounting sleeve into the dashboard or optional

adapter. Do not force the sleeve into the opening or cause

it to bend or bow.

b. Locate the series of bend-tabs along the top, bottom and

sides of the mounting sleeve. With the sleeve fully insert-

ed into the dashboard opening, bend as many of the tabs

outward as necessary so that the sleeve is ﬁrmly secured

to the dashboard.

c. Install support strap to make the unit more stable.

Place the radio in front of the dashboard opening so the wiring

can be brought through the mounting sleeve.

CAUTION! Be careful not to damage the car wiring.

EJECT

A/V

INPUT

Wiring

WARNING! Only connect the unit to a 12-volt power supply with proper grounding.

Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the bat-

tery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.

NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The

VM9114 uses one 15 amp fuse, located in the black ﬁlter box in-line with the main wire harness.

Final Installation

After completing the wiring connections, turn the unit on to conﬁrm operation (ignition switch must be on). If

unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off

the ignition switch and proceed with ﬁnal mounting of the chassis.

Connect wiring adapter to existing wiring harness.

Connect antenna lead.

Carefully slide the radio into the mounting sleeve, making

sure it is right-side-up, and secure with the original 4 screws.

Attach one end of the perforated support strap (supplied) to

the screw stud, which is screwed into the threaded insert on

the back of the unit, using the hex nut provided. Fasten the

other end of the perforated strap to a secure part of the

dashboard either above or below the radio using the screw

and hex nut provided. Bend the strap to position it as

necessary.

Replace any items you removed from the dashboard.

ISO-DIN Installation

Remove mounting sleeve brackets.

Remove trim ring.

Mount factory brackets on new radio using existing screws

from old radio.

Slide radio chassis into dash opening and secure.

Re-install dash panel.

EJECT

A/V

INPUT

EJECT

A/V

INPUT

CAUTION! The rear of the radio must be

supported with the strap to prevent dam-

age to the dashboard from the weight of

the radio or improper operation due to

vibration.

NOTE: For proper operation of the CD/

DVD player, the chassis must be mounted

within 20° of horizontal. Make sure the unit

is mounted within this limitation.

Remove Mounting

Sleeve Brackets

EJECT

A/V

INPUT

Harness Cord

Auto antenna control (connect to antenna

control lead & power supply of antenna

amplifier)

External power amplifier control

Antenna Jack

REAR R

REAR L

BLUE

BLUE/WHITE

WHITE/BLACK -

GREEN/BLACK -

WHITE +

GREEN +

PURPLE +

PURPLE/BLACK -

GREY/BLACK -

GREY +

Car

Mute (leave open if not connected)

BROWN

Car Phone

FRONT L

FRONT R

REAR R

REAR L

MUTE

P.CONT

ANT.CONT

ACC

BLACK

YELLOW

RED

FUSE (15A)

Battery

Ignition Switch

BATTERY

BATTERY +

Ground

BATT

ACC

GND

PINK

External Power Amplifier

Antenna

PRK SW

PARKING BRAKE

Wiring Diagram

IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or

have the installation handled by an experienced technician.

Need Help?

For technical assistance, call the Jensen

customer support line at 1-800-323-4815.

Otros manuales para VM9114

Tabla de contenidos

Otros manuales de Receptor de coche de Jensen

Jensen

Jensen VM9312HD - DVD Player With LCD Monitor Manual de usuario

Jensen

Jensen powersports hd1bt Manual de usuario

Jensen

Jensen VM9312HD - DVD Player With LCD Monitor Manual de usuario

Jensen

Jensen Mobile Multimedia AM/FM/DVD Receiver... Manual de usuario

Jensen

Jensen MP5000 - GUIDE Manual de usuario

Jensen

Jensen VM9324 Manual de usuario

Jensen

Jensen AWM968BK Manual de usuario

Jensen

Jensen VM9213 - Touch Screen MultiMedia Receiver Manual de usuario

Jensen

Jensen VM9226BT Manual de usuario

Jensen

Jensen DMR2116i Manual de usuario

Jensen

Jensen MP6512i Manual de usuario

Jensen

Jensen JRV212T Manual de usuario

Jensen

Jensen DV2011 Manual de usuario

Jensen

Jensen MP3510 Manual de usuario

Jensen

Jensen MP1314 Manual de usuario

Jensen

Jensen MCD 5110 Manual de instrucciones

Jensen

Jensen CD450K Instrucciones de montaje

Jensen

Jensen VR209 Manual de usuario

Jensen

Jensen DMX5020 Manual de usuario

Jensen

Jensen VM9510TS Manual de usuario

Jensen

Jensen VM9215BT Manual de usuario

Jensen

Jensen DV2007 Manual de usuario

Jensen

Jensen VX4010 Manual de usuario

Jensen

Jensen Heavy Duty JHD1620 Manual de usuario

Manuales populares de Receptor de coche de otras marcas

Motorola

Motorola VWA63 Manual de usuario

Nextar

Nextar D3201 Manual de usuario

Alpine

Alpine CDE-163BT Manual de usuario

Pioneer

Pioneer DEH-P645R Manual de usuario

Axxera

Axxera XDMA7600 Instrucciones de funcionamiento

XM OnyX Manual de usuario

Sound Storm

Sound Storm STM93R Manual de usuario

Soundstream

Soundstream VIR-5000 Manual de usuario

Avson

Avson MKT Platform Manual de usuario

Sony

Sony MEX-1HD - Audio Library System Manual de usuario

Pioneer

Pioneer DVH-P500UB Manual de usuario

JVC

JVC KD-AHD69 Manual de usuario

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manual de usuario

Sony

Sony CDX-4160 - Cd Receiver Manual de usuario

XFIRE AUDIO

XFIRE AUDIO BMW42S Manual de usuario

VDO

VDO CD 2253 Manual de usuario

Volvo

Volvo 13 84 580 Manual de usuario

ZENEC

ZENEC ZE-160DVD Manual de usuario