Jenn-Air JMW2327WS01 Manual de usuario

INSTALLATION INSTRUCTIONS

27" (68.6 CM) AND 30" (76.2 CM) ELECTRICBUILT-IN

MICROWAVE/OVEN COMBINATION

INSTRUCTIONSD'INSTALLATION

FOURA MICRO-ONDES ETFOURCONVENTIONNEL

ELECTRIQUESCOMBINES ETENCASTRESDE

27" (68,6 CM) ET30" (76,2 CM)

Table of Contents /Table des mati_res

BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY ................. 2

INSTALLATION REQUIREMENTS ...................................................... 2

Tools and Parts .................................................................................. 2

Location Requirements ...................................................................... 2

Electrical Requirements ..................................................................... 4

INSTALLATION INSTRUCTIONS ........................................................ 5

Prepare Built-In Microwave/Oven Combination ................................ 5

Remove Oven Door ............................................................................ 5

Make Electrical Connection ............................................................... 5

Install Oven ......................................................................................... 7

Complete Installation ........................................................................ 8

SI_CURITI_ DU FOUR .&MICRO-ONDES ET DU FOUR

CONVENTIONNEL COMBINI_S ET ENCASTRI_S .............................. 9

EXIGENCES D'INSTALLATION ........................................................... 9

Outillage et pieces ............................................................................. 9

Exigences d'emplacement ................................................................ 9

Specifications electriques ................................................................ 11

INSTRUCTIONS D'INSTALLATION .................................................. 12

Preparation de I'ensemble des fours encastres

(micro-ondes/conventionnel) ........................................................... 12

D_pose de la porte du four .............................................................. 12

Raccordement electrique ................................................................ 12

Installation du four ........................................................................... 14

Achever I'installation ........................................................................ 16

iMPORTANT:

Save for local electrical inspector's use.

iMPORTANT :

_, conserver pour consultation par I'inspecteur local des installations 61ectriques.

W10221384B

BUILT-INMICROWAVE/OVEN COMBINATION SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Adjustable wrench or %" wrench

• Phillips screwdriver

• Flat-blade screwdriver

• Measuring tape

• Drill (for wall cabinet installations

• 1V4" (3.4 cm) drill bit (for wall cabinet installations)

• Level

Parts needed

• UL listed or CSA approved conduit connector

• UL listed wire connectors

Parts supplied

• Six # 8-14 x 3/4"screws

• Bottom vent

• Two # 8-18 x 3/8"screws - bottom vent

Check local codes. Check existing electrical supply. See

"Electrical Requirements."

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

Make sure you have everything needed for correct installation.

IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

Recessed installation area must provide complete enclosure

around the recessed portion of the oven.

Grounded electrical supply is required. See "Electrical

Requirements" section.

Electrical supply junction box should be located 3" (7.6 cm)

maximum below the support surface when the oven is

installed in a wall cabinet. A 1V4"(3.4 cm) minimum diameter

hole should have been drilled only in the left rear corner of the

support surface to pass the appliance cable through to the

junction box.

Oven support surface must be solid, level and flush with

bottom of cabinet cutout. Floor must be able to support atotal

weight of (microwave and built-in oven) of 249 Ibs (113 kg) for

30" (76.2 cm) oven and 236 Ibs (107 kg) for 27" (68.6 cm)

oven.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194 ° (90°C).

Product Dimensions Cabinet Dimensions

27" (68.6 cm) models

A. 25 ¼" (64.1 cm) max. recessed

width

B. 43_" (109.4 cm) max. overall

height

C. 26¾" (67.9 cm) max. overall

width

D. 235_''(60.0 cm) max. overall

depth

E. 41" (104.2 cm) max. recessed

height

30" (76.2 cm) models

A. 28" (71.1 cm) max. recessed

width

B. 43_" (109.4 cm) max. overall

height

C. 29_" (75.6 cm) max. overall

width

D. 235_'' (60.0 cm) max. overall

depth

E.41" (104.2 cm) max. recessed

height

27" (68.6 cm) models

A. 27" (68.6 cm) min. cabinet width

B.43_" (110.0 cm) from bottom

of cutout to bottom of upper

cabinet door

C. 19 ¼" (48.9 cm) recommended

bottom of cutout to floor. 4"

(10.2 cm) to 19¼" (48.9 cm)

bottom of cutout to floor is

acceptable.

D. 25 ½" (64.8 cm) cutout width

E. 1½" (3.8 cm) min. bottom of

cutout to top of cabinet door

F. 41 ¼" (104.8 cm) cutout height

G. 24" (61.0 cm) minimum cutout

depth

30" (76.2 cm) models

A. 3G' (76.2 cm) min. cabinet

width

B. 43_" (110.0 cm) from bottom

of cutout to bottom of upper

cabinet door

C. 19¼" (48.9 cm) recommended

bottom of cutout to floor. 4"

(10.2 cm) to 19¼" (48.9 cm)

bottom of cutout to floor is

acceptable.

D. 28½" (72.4 cm) cutout width

E. 1½" (3.8 cm) min. bottom of

cutout to top of cabinet door

F. 41 ¼" (104.8 cm) cutout height

G. 24" (61.0 cm) minimum cutout

depth

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and the wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

oven is properly grounded.

This oven must be connected to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70-latest edition or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. O-M91-1atest edition, and all local

codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

• Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial number rating

plate. The model/serial number rating plate is located near

center vent of the lower oven. See the following illustration.

Models rated from 7.3 to 9 kW at 240 volts (5.4 to 7.4 kW at

208 volts) require a separate 40-amp circuit. Models rated at

4.8 kW and below at 240 volts (3.6 kW and below at 208 volts)

require a separate 20-amp circuit.

A circuit breaker is recommended.

Connect directly to the fused disconnect (or circuit breaker

box) through flexible, armored or nonmetallic sheathed,

copper cable (with grounding wire). See "Make Electrical

Connection" section.

Flexible conduit from the oven should be connected directly to

the junction box.

Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

A UL listed or CSA approved conduit connector must be

provided.

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

A. Model/serial number plate (located on

underside of center vent)

INSTALLATIONINSTRUCTIONS

1. Decide on the final location for the oven. Avoid drilling into or

severing wiring during installation.

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

3= Grasp the edges of the oven door with both hands and close

the oven door until it will no longer close. Lift and pull oven

door toward you and remove. Set the oven door(s) aside on a

covered work surface.

To avoid floor damage, set the oven onto cardboard prior to

installation. Do not use handle or any portion of the front

frame for lifting.

Remove the shipping materials and tape from the oven.

Remove the hardware package from inside the bag containing

literature.

Remove and set aside racks and other parts from inside the

oven.

Move oven and cardboard close to the oven's final location.

R!em Ove ©oo

IMPORTANT: Use both hands to remove oven door(s).

1. Open the oven door to the full open position.

2. Locate the oven door latches in both corners of the oven door,

and rotate the latches forward to the unlocked position.

Q,<eEII QI[ioQI ,'

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A. Oven door latch in locked

position B. Oven door latch in unlocked

position

This oven is manufactured with a neutral (white) power supply

wire and a cabinet-connected green (or bare) ground wire twisted

together.

1. Disconnect power.

2. Feed the flexible conduit from the oven through the opening in

the cabinet.

3. Remove junction box cover, if it is present.

4= Install a UL listed or CSA approved conduit connector to the

junction box.

A. UL fisted or CSA approved conduit connector

5. Route the flexible conduit from the oven to the junction box

through a UL listed or CSA approved conduit connector.

6. Tighten screws on conduit connector.

7. See "Electrical Connection Options Chart" to complete

installation for your type of electrical connection.

Electrical Connection Options Chart

Ifyour home has: Goto section:

4-wire 4-wire Cable from Home

Power Supply

3-wire 3-wire Cable from Home

___m Power Supply

1/2" )

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power supply in

the U.S. where local codes do not allow grounding through

neutral, New Branch circuit installations (1996 NEC), mobile

homes and recreational vehicles, new construction and in

Canada. ......................................................................

A. Cable from home power supply

B. Black wires

C. Red wires

D. 4-wire flexible conduit from

oven

E.Junction box

F. White wires

G. UL fisted wire connectors

H. Green (or bare) ground wires

I. UL listed or CSA approved

conduit connector

Connect the 2 black wires (B) together using a UL listed wire

connector.

Connect the 2 red wires (C) together using a UL listed wire

connector.

Untwist white wire from green (or bare) ground wire coming

from the oven.

Connect the 2 white wires (F)together using a UL listed wire

connector.

Connect the green (or bare) ground wire (H) from the oven

cable to the green (or bare) ground wire (in the junction box)

using a UL listed wire connector.

Install junction box cover.

3-Wire Cable from Home Power Supply -U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply

where local codes permit a 3-wire connection.

A. Cable from home power supply F. 4-wire flexible conduit from

B. Junction box oven

C. Black wires G. Red wires

D. White wires H. UL listed wire connectors

E. Green (or bare) ground wire I. UL listed or CSA approved

(from oven) conduit connector

Connect the 2 black wires (C) together using a UL listed wire

connector.

Connect the 2 white wires (D) and the green (or bare) ground

wire (of the oven cable) using a UL listed wire connector.

Connect the 2 red wires (G) together using a UL listed wire

connector.

Install junction box cover.

Ores

Using 2 or more people, lift oven partially into cabinet cutout.

Use the oven opening as an area to grip.

NOTE: Push against seal area of oven front frame when

pushing oven into cabinet. Do not push against outside

edges.

Push oven completely into cabinet and center oven into

cabinet cutout.

Securely fasten oven to cabinet using the # 8-14 x 3/4"screws

provided. Insert the screws through holes in decorative trim.

Do not overtighten screws.

4. The bottom vent is taped to the top of the oven chassis

enclosure. See the following instructions to install.

• Align mounting hole in bottom vent to holes in the oven

frame.

• With one #8-18 x 3/8"screw for each side of the vent,

fasten vent securely to the oven frame.

IMPORTANT: Do not block air intake along bottom of oven.

5. Replace oven racks.

6. Grasp door at each side.

7. Replace oven door by aligning and inserting ends of hinges

into hinge slots in the oven frame.

8. Push hinges in as far as they will go and open the oven door

to the fully open position. You should feel the oven door drop

into place.

9. Move the latches back to the locked position.

10. Check that door is free to open and close. If it is not, repeat

the removal and installation procedures. See "Remove Oven

Door" section.

11. Reconnect power.

12. Display panel will light briefly, and the clock should appear in

the display.

13. If display panel does not light, please reference the

"Assistance or Service" section of the Use and Care Guide or

contact the dealer from whom you purchased your oven.

A. Decorative trim

B. Insert screw.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For oven use and cleaning, read the Use and Care Guide.

Check Operation of Lower Oven

1. Turn power on.

2. At first use, set up the language, regional settings, clock, date

and screen appearance. For more details, read the Use and

Care Guide.

3. Press OVEN.

4. Touch BROIL.

5. Set the temperature.

6. Touch START.

If oven(s) does not operate, check the following:

• Household fuse is intact and tight; or circuit breaker has

not tripped.

• Electrical supply is connected.

• See "Troubleshooting" section in the Use and Care Guide.

7. When oven has been on for 5 minutes, feel for heat.

If you do not feel heat or if an error message appears in the

display, turn off the oven and contact qualified technician.

8. Touch CANCEL OVEN.

Check Operation of Microwave Oven

1. Fill a microwave-safe container with 1 cup (250 mL) of water

and place container inside microwave oven. Close door firmly.

2. From the main menu press microwave or open microwave

oven door.

3. Touch COOK.

4. Set power level, temperature and cook time to "2:00" minutes.

5. Touch START.

If microwave oven does not operate, check the following:

• Household fuse is intact and tight; or circuit breaker has

not tripped.

• Electrical supply is connected.

• See "Troubleshooting" section in the Use and Care Guide.

When display reads "1:00" minute, open microwave oven

door. The microwave oven should stop cooking. Close door

firmly. The interior microwave oven light should turn off.

6= Touch START to resume a preset cycle. The microwave oven

should begin cooking, and the microwave oven interior light

should be on. Let microwave oven complete cooking time.

Tones will sound at the end of the cooking time, and the

microwave oven will shut off.

7. Open microwave oven door and slowly remove container.

Water in container should be hot. To set the clock and other

oven functions, refer to the Use and Care Guide.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the Use

and Care Guide or contact the dealer from whom you purchased

your built-in and microwave ovens.

SI CURITI DU FOUR MICRO- NDES ETDU F UR

CONVENTIONNEL COMBINES ETENCASTRES

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6ces et de blessures graves & vous

et &d'autres.

Tousles messages de securite suivront le symbole d'alerte de s6curite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_ces ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s6curite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiqu6s ici.

Outillage n_cessaire

• OI6 a molette ou cle de 5/8"

• Tournevis Phillips

• Tournevis a lame plate

• Metre ruban

• Perceuse (pour I'installation dans un placard mural)

• Foret de 11/4'' (3,4 cm) (pour I'installation dans un placard

mural)

• Niveau

Pieces necessaires

• Connecteur de conduit (homologation UL ou CSA)

• Connecteurs de fils (homologation UL)

Pi_ces fournies

• Vis n° 8-14 x 3/4"

• 12ventdu fond

• Deux vis n° 8-18 x 3/8"- event du fond

Consulter les codes Iocaux. Verifier I'alimentation electrique

existante. Voir "Specifications electriques".

II est recommande de faire realiser tous les raccordements

electriques par un electricien qualifie agree.

£x { jences d ®rap c c®m®n

S'assurer d'avoir tout le necessaire pour une installation

convenable.

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

• Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards. Ces dimensions tiennent compte

des degagements de separation necessaires pour le four.

• L'espace d'installation doit permettre la formation d'une

enceinte complete autour de la partie encastree du four.

• Une source d'electricite avec liaison & la terre est necessaire.

Voir la section "Specifications electriques".

Le boYtier de connexion doit _tre situ6 a 3" (7,6 cm) maximum

au-dessous de la surface de support Iorsque le four est

installe dans un placard mural. Un trou de diametre minimal

de 1V4"(3,4 cm) doit avoir et6 perce uniquement dans I'angle

arriere gauche de la surface de support pour le passage du

c&ble d'alimentation de I'appareil jusqu'au boYtierde

connexion.

La surface de support du four doit _tre robuste, horizontale et

en affleurement avec le bas de I'ouverture decoup6e dans le

placard. Le plancher doit _tre capable de supporter un poids

total (four a micro-ondes et four encastre) de 249 Ib (113 kg)

pour le four de 30" (76,2 cm) et de 236 Ib (107 kg) pour le four

de 27" (68,6 cm).

IMPORTANT:Pourevitertoutdommage,consulterle

constructeuroulefabricantduplacardpourdeterminersiles

materiauxutilisesnesubirontpasunchangementdecouleur,une

destratificationoud'autresdommages.Cefouraet6congu

conformementauxexigencesULetauxnormesdelaCSA

International;ilrespectelatemperaturemaximaleautoriseepour

lesplacardsenbois:194°F(90°C).

Dimensions du produit

ModUles de 27" (68,6 cm)

A. 251/4" (64,1 cm) de largeur

d'encastrement max.

B. 43_" (109,4 cm) de hauteur

totale max.

C. 26s/4 '' (67,9 cm) de largeur

totale max.

D. 23_" (60,0 cm) de profondeur

totale max.

E. Hauteur de I'encastrement de

41" (104,2 cm) max.

ModUles de 30" (76,2 cm)

A. 28" (71,1 cm) de largeur

d'encastrement max.

B. 43_" (109,4 cm) de hauteur

totale max.

C. 29s/4 '' (75,6 cm) de largeur

totale max.

D. 23_" (60,0 cm) de profondeur

totale max.

E. Hauteur de I'encastrement de

41" (104,2 cm) max.

Dimensions du placard

[

ModUles de 27" (68,6 cm)

A. 27" (68,6 cm) min. de largeur

de placard

B. 43_" (110,0 cm) du fond de

I'encastrement au-dessous de

la porte du placard sup_rieur

C. Distance recommand_e de

19 _" (48,9 cm) entre le bas

de I'ouverture et le plancher.

Une distance de 4" (10,2 cm)

19¼" (48,9 cm) entre le bas

de I'ouverture et le plancher

est acceptable.

D. 251/2'' (64,8 cm) Largeur de

/'encastrement

E. 11/2''(3,8 cm) min. du fond de

I'encastrement au-dessus de

la porte du placard

F. 41 _" (104,8 cm) Hauteur

d'encastrement

G. 24" (61.0 cm) profondeur

d'encastrement minimale

ModUles de 30" (76,2 cm)

A. 30" (76,2 cm) min. de largeur de

placard

B. 43_" (110,0 cm) du fond de

I'encastrement au-dessous de

la porte du placard sup_fieur

C. Distance recommand_e de

19_" (48,9 cm) entre le bas de

I'ouverture et le plancher. Une

distance de 4" (10,2 cm) _19¼"

(48,9 cm) entre le bas de

I'ouverture et le plancher est

acceptable.

D. 281/2"[72,4 cm] Largeur de

/'encastrement

E. 11/2''(3,8 cm) min. du fond de

I'encastrement au-dessus de la

porte du placard

F. 41 _" (104,8 cm) Hauteur

d'encastrement

G. 24" (61.0 cm) profondeur

d'encastrement minimale

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Horno de Jenn-Air

Jenn-Air

Jenn-Air W2451 Manual de usuario

Jenn-Air

Jenn-Air JJW2427DS Manual de usuario

Jenn-Air

Jenn-Air JJW8530DDB28 Manual de usuario

Jenn-Air

Jenn-Air JJW2827DB01 Manual de usuario

Jenn-Air

Jenn-Air JJW8630 Manual de usuario

Jenn-Air

Jenn-Air W30400P Manual de usuario

Jenn-Air

Jenn-Air JJW6024HL Manual de usuario

Jenn-Air

Jenn-Air 8101P423-60 Manual de usuario

Jenn-Air

Jenn-Air JJW3430LM01 Manual de usuario

Jenn-Air

Jenn-Air JMW3430DT Manual de usuario

Jenn-Air

Jenn-Air JJW7530DDS Manual de usuario

Jenn-Air

Jenn-Air JJW2327WS Manual de usuario

Jenn-Air

Jenn-Air 81t2P180_60 Manual de usuario

Jenn-Air

Jenn-Air W27100 Manual de usuario

Jenn-Air

Jenn-Air JJW3430 Manual de usuario

Jenn-Air

Jenn-Air JJW9527 Guide Manual de usuario

Jenn-Air

Jenn-Air JJW3830WB00 Manual de usuario

Jenn-Air

Jenn-Air JJW8127 Manual de usuario

Jenn-Air

Jenn-Air JJW3830 Manual de usuario

Jenn-Air

Jenn-Air ELECTRIC CONVENIENCE OVEN Manual de usuario

Jenn-Air

Jenn-Air JJW2830LL Manual de usuario

Jenn-Air

Jenn-Air JJW9527 Guide Manual de usuario

Jenn-Air

Jenn-Air W131 Manual de usuario

Jenn-Air

Jenn-Air WM27160 Manual de usuario

Manuales populares de Horno de otras marcas

Bosch

Bosch HVA531NS0 Manual de usuario

Electrolux

Electrolux EOF6P46X Manual de usuario

NEFF

NEFF B44S32 5GB Series Manual de usuario

Combi

Combi BLODGETT BC142GDS Manual de usuario

AEG

AEG COMPETENCE 311704300 Manual de usuario

Falcon

Falcon DOMINATOR PLUS G3106 Series Guía del usuario

Rational

Rational SCC WE 61G Manual de usuario

Smeg

Smeg DOSPA38X Manual de instalación y operación

Electrolux

Electrolux air-o-convect 20 GN 2/1 Manual de usuario

Miele

Miele HR 1954-2 Manual de usuario

KHIND

KHIND OT50 Manual de usuario

Henny Penny

Henny Penny Smoker Box Manual de usuario

Lang

Lang ECOD-AP Manual de usuario

AEG

AEG BEK455310M Manual de usuario

Frigidaire

Frigidaire FNGE90JGR Manual de usuario

Hotpoint

Hotpoint FE9 S831 JSH IX Manual de usuario

GE Advantium SCB2000 Manual de usuario

AEG

AEG DE401301DM Manual de usuario