JBL BPX500.1 Manual de usuario

BPX500.1

2 CHANNEL

POWER AMPLIFIER

SERVICE MANUAL

JBL Consumer Products

250 Crossways Park Dr.

Woodbury, New York 11797 Rev1 2/2004

CONTENTS

Specifications………………………….…………………..……1

Features…………………………………………………………2

Test Conditions And Notes……………………………………2

Controls/connections…………………………………..………3

Mounting…………………………………………….…..………3

Applications………………………………………..……………4

Typical System Configuration…………………………………5

Troubleshooting……………………………………….……..…6

PCB drawings……………………………………..……………7

Electrical Parts List……………………………………………10

Mechanical Parts List……………….………………..………13

Block Diagrams……………………………………….………14

Semiconductor Pinouts………………………………………15

Exploded view…………………………………………………20

Schematics……………………………………………….……21

Packing………………………………….………………………30

SPECIFICATIONS

Power Output, 4 Ohms: n/a

Power Output, 2 Ohms: 250W x 2

Power Output, Bridged, 4 Ohms: 500W x 1

Power Output, Parallel, 1 Ohm: 500W x 1

MIN. Speaker Impedance: 1 ohm

Frequency Response: 20Hz~320Hz, -3dB

Input Sensitivity (RCA type): 250mV~6V

THD + Noise (4 Ohms): 0.5%

Signal-to-Noise: 93 dB

Maximum Current Draw: 50A

Fuse Replacement: 30Ax2

External Dimensions:

Length 12 ¼” (312mm)

Width 13” (330mm)

Depth 2 9/16” (66mm)

JBL continually strives to improve its products. New materials, production methods and design refinements are introduced into existing

models without notice as a routine expression of our design philosophy. For this reason, Power Series Multichannel Automotive

Amplifiers may differ in some respects from their published specifications and descriptions, but will always equal or exceed the original

specifications unless otherwise stated.

Power Amplifier

BPX500.1

APPLICATIONS – BPx MODELS

To the right are several application

diagrams to help plan your subwoofer

system installation. Figures 1 through 3

show how to configure the JBL Power

Series subwoofer amplifiers (models

BPx500.1, BPx1100.1 and BPx2200.1)

for 2-channel, bridged-mono and

parallel-mono operation

“Setting the Output Mode” on page 6).

NOTE: For simplicity, Figures 1 through

3 do not show power, remote and input

connections.

NOTE: If the nominal impedance

of your speaker system is close to

2 ohms, be prepared to try both

bridged and parallel configurations to

determine which performs better.

BPx Amplifier

(partial rear panel)

SEE MANUAL FOR PARALLEL CONNECTION

2 CHANNEL

BRIDGED

PARALLEL

CH 1

CH 2

SPEAKER OUTPUTS

NEON

Subwoofer Subwoofer

Set OUTPUT MODE

to 2CH/BR

(on input panel)

PARALLEL 2CH/BR

OUTPUT MODE

12dB 24dB

32Hz 320Hz

FREQ

SLOPE

X-OVER

BPx Amplifier

(partial rear panel)

SEE MANUAL FOR PARALLEL CONNECTION

2 CHANNEL

BRIDGED

PARALLEL

CH 1

CH 2

SPEAKER OUTPUTS

NEON

Subwoofer (less than 2 ohms)

Set OUTPUT MODE

to PARALLEL

(on input panel)

PARALLEL 2CH/BR

OUTPUT MODE

12dB 24dB

32Hz 320Hz

FREQ

SLOPE

X-OVER

jumper

Figure 1. The JBL Power Series

subwoofer amplifier is set to

2-channel mode to drive a pair

of subwoofers.

Figure 2. The JBL Power Series

subwoofer amplifier is set to

bridged (mono) mode to drive

a single subwoofer. Use this

mode only when the nominal

impedance of the speaker

system is 2 ohms or greater.

Figure 3. The JBL Power Series

subwoofer amplifier is set to

parallel mode to drive a single

subwoofer. Use this mode only

when the nominal impedance

of the speaker system is less

than 2 ohms.

NOTE: A jumper is added

between the + terminals.

BPx Amplifier

(partial rear panel)

SEE MANUAL FOR PARALLEL CONNECTION

2 CHANNEL

BRIDGED

PARALLEL

CH 1

CH 2

SPEAKER OUTPUTS

NEON

Subwoofer (2 ohms or greater)

Set OUTPUT MODE

to 2CH/BR

(on input panel)

PARALLEL 2CH/BR

OUTPUT MODE

12dB 24dB

32Hz 320Hz

FREQ

SLOPE

X-OVER

Power Series Amp OM 5/20/03 10:51 AM Page 3

Power Amplifier

BPX500.1

TROUBLESHOOTING

SYMPTOM LIKELY CAUSE SOLUTION

No audio No voltage at BATT+ Check voltages at

(POWER LED or REM terminals, amplifier terminals

is off) or bad or no ground with VOM

connection

No audio DC voltage on Amplifier may need

(PROTECT LED amplifier output service; see enclosed

flashes every warranty card for

4 sec.) service information

No audio Amplifier is Make sure amplifier

(PROTECT overheated cooling is not blocked

LED is on) at mounting location;

verify speaker-system

impedance is within

specified limits (see

“Specifications” on the

next page)

No audio Voltage less than 9V on Check vehicle

(PROTECT BATT+ connection charging system for

and POWER defective voltage

LEDs flash) regulator

I-E/OPT LED Amplifier is being Check INPUT

is on all times overdriven LEVEL setting;

(not flashing) see previous page

No audio Voltage more than 16V Check vehicle

(PROTECT or less than 8.5V on charging system for

LED is on) BATT+ connection defective voltage

regulator

Distorted audio Input sensitivity is Check INPUT

not set properly, or LEVEL setting; or

amplifier or source check speaker wires

unit is defective for shorts or grounds

Distorted audio Short circuit in Remove speaker leads

and PROTECT speaker or wire one at a time to locate

LED flashes shorted speaker or

wire, then repair

Music lacks Speakers are not Check speaker

“punch” connected properly connections for

proper polarity

Power Amplifier

BPX500.1

PAS132-01

REV.0

A20K

623PCB4-B

A20KA20K

623PCB4-B

A20K

623PCB4-B

A20K

623PCB4-B 623PCB4-B

A20K

623PCB4-B

A20KA20K

623PCB4-B 623PCB4-B

A20K A20K

623PCB4-B 623PCB4-B

A20K

VR701

R701

MOD02

VR701

R701

MOD02

VR701

R701

MOD02

VR701

R701

MOD02 MOD02

MOD02

R701R701

VR701

R701

MOD02

VR701

R701

MOD02 MOD02

R701

VR701

R701

MOD02 MOD02

R701

VR701

Tabla de contenidos

Otros manuales de Amplificador de coche de JBL

JBL

JBL GTO-1004E Manual de usuario

JBL

JBL GT5-A604 Manual de usuario

JBL

JBL GTO4000 Manual de usuario

JBL

JBL GRAND TOURING GTO4060 Manual de usuario

JBL

JBL gto1201.1 II Manual de usuario

JBL

JBL GTO24001 Manual de usuario

JBL

JBL MS-A1004 Manual de usuario

JBL

JBL GTS300 Manual de usuario

JBL

JBL A3000GTi Manual de usuario

JBL

JBL GTO5355 Manual de usuario

JBL

JBL P-7520 Manual de usuario

JBL

JBL CS Series Manual de usuario

JBL

JBL Grand Touring Series GTO1004 Manual de usuario

JBL

JBL Grand Touring Series GTO504 Manual de usuario

JBL

JBL GT5-A402 Manual de usuario

JBL

JBL CS300.1 Manual de usuario

JBL

JBL GTH400 Manual de usuario

JBL

JBL Grand Touring Series GTO14001 Manual de usuario

JBL

JBL DECADE DA1002 Manual de usuario

JBL

JBL A6000GTi Manual de usuario

JBL

JBL GTS180 Manual de usuario

JBL

JBL GT5-A402E Manual de usuario

JBL

JBL Grand Touring Series GTO504 Manual de usuario

JBL

JBL GTO5355 Manual de usuario

Manuales populares de Amplificador de coche de otras marcas

Cyfre

Cyfre CHACDMA-819 Manual de usuario

MTX

MTX Thunder Marine TM904 Manual de usuario

MTX

MTX Thunder TA Super TA92001 Manual de instrucciones

Lanier

Lanier 480-0239 Instrucciones de funcionamiento y mantenimiento

Kenwood

Kenwood KAC-642 Manual de usuario

Pioneer

Pioneer GM-D8500M Manual de usuario

Jensen

Jensen XA4150 Manual de usuario

Sony

Sony XM-405EQX Marketing Specifications Manual de usuario

Audiopipe

Audiopipe AQX-660.2 Manual de usuario

Clarion

Clarion APA2001 APA2001 APA2001 Guía de inicio rápido

Sony

Sony XM-7547 Manual de usuario

Alpine

Alpine PDX11000 - Amplifier Manual de usuario

Steg

Steg Qx Mos 105.4x Manual de usuario

JL Audio

JL Audio HD900/5 Manual de usuario

Memphis

Memphis 16-MC5.700 Manual de usuario

Audiopipe

Audiopipe APSM-1150 Manual de usuario

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manual de usuario

Kenwood

Kenwood KAC-PS811D Manual de usuario