JB Systems M-Quantium Laser Manual de usuario

ENGLISH USER MANUAL

JB SYSTEMS®1/36 µ-LASER

OPERATION MANUAL

Thank you for buying this JB Systems®product. To take full advantage of all possibilities

and for your own safety, please read these operating instructions very carefully before you

start using this unit.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the

current European and national guidelines. Conformity has been established and the

relevant statements and documents have been deposited by the manufacturer.

This device was designed to produce decorative effect lighting and is used in light show

systems.

Fantastic laserburst effect using 2 lasers of a different color

Thanks to special grating technology the beams are split-up in a lot of separate laser

beams pointing in all directions to create an amazing, room filling effect.

Perfect for projections on walls and ceilings in bars, bedrooms, parties, etc.

The color of the beams changes all the time using laser blanking technology.

Plug & play: no expensive controllers needed!

A multifunctional infrared remote can be used to control the functions

Standalone mode with built-in microphone or automatic shows can be selected.

All kinds of strobe effects

Adjustable mounting bracket (stand) and power adapter included.

Key actuated on/off switch for additional safety

Complies to EN/IEC 60825-1 Ed2, 2007-03 for Laser Safety

BEFORE USE

Before you start using this unit, please check if there’s no transportation damage. Should

there be any, do not use the device and consult your dealer first.

Important: This device left our factory in perfect condition and well packaged. It is

absolutely necessary for the user to strictly follow the safety instructions and warnings in

this user manual. Any damage caused by mishandling is not subject to warranty. The

dealer will not accept responsibility for any resulting defects or problems caused by

disregarding this user manual.

Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to

add this user manual.

Check the contents:

Check that the cardboard box contains the following items:

µ-LASER

IR remote control

2 keys (for key switch)

Power supply

Base plate

Fixation arm

Operating instructions

ENGLISH USER MANUAL

JB SYSTEMS®2/36 µ-LASER

SAFETY INSTRUCTIONS:

To protect the environment, please try to recycle the packing material as much as

possible.

A new light effect sometimes causes some unwanted smoke and/or smell. This is normal

and disappears after some minutes.

To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

To avoid condensation to be formed inside, allow the unit to adapt to the surrounding

temperatures when bringing it into a warm room after transport. Condense sometimes

prevents the unit from working at full performance or may even cause damages.

This unit is for indoor use only.

Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may

result. If a foreign object enters the unit, immediately disconnect the mains power.

Locate the fixture in a well ventilated spot, away from any flammable materials and/or

liquids. The fixture must be fixed at least 50cm from surrounding walls.

Don’t cover any ventilation openings as this may result in overheating.

Prevent use in dusty environments and clean the unit regularly.

Keep the unit away from children.

Inexperienced persons should not operate this device.

The safe ambient temperature is between 15° & 40°C. Don’t use this unit at higher

ambient temperatures.

Make sure the area below the installation place is free from unwanted persons during

rigging, de-rigging and servicing.

Always unplug the unit when it is not used for a longer time or before replacing the bulb

or start servicing.

The electrical installation should be carried out by qualified personal only, according to

the regulations for electrical and mechanical safety in your country.

Check that the available voltage is not higher than the one stated on the rear panel of the

unit.

CAUTION: To reduce the risk of electric shock, do not

remove the top cover. No user-serviceable parts

inside. Refer servicing to qualified service personnel

only.

The lightning flash with arrowhead symbol within the equilateral triangle is

intended to alert the use or the presence of un-insulated “dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user

to the presence of important operation and maintenance (servicing) instructions

in the literature accompanying this appliance.

This symbol means: indoor use only

This symbol means: Read instructions

This symbol determines: the minimum distance from lighted objects. The

minimum distance between light-output and the illuminated surface must be

more than 1 meter

The device is not suitable for direct mounting on normally flammable surfaces.

(suitable only for mounting on non-combustible surfaces)

ENGLISH USER MANUAL

JB SYSTEMS®3/36 µ-LASER

The power cord should always be in perfect condition. Switch the unit immediately off

when the power cord is squashed or damaged. It must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

Never let the power-cord come into contact with other cables!

In order to avoid a hazard, the unit shall only be used with the AC-adaptor delivered with

it. If the AC-adaptor is damaged, a same model adaptor shall be used only.

Don’t connect the unit to any dimmer pack.

Always use an appropriate and certified safety cable when installing the unit.

In order to prevent electric shock, do not open the cover. Apart from the lamp and mains

fuse there are no user serviceable parts inside.

Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a

fuse of the same type and electrical specifications!

In the event of serious operating problems, stop using the fixture and contact your dealer

immediately.

The housing and the lenses must be replaced if they are visibly damaged.

Please use the original packing when the device is to be transported.

Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of

persons suffering from epilepsy.

LASER SAFETY INSTRUCTIONS:

According to the EN/IEC 60825-1 Ed2, 2007-03 regulations, this laser falls under the

classification 3B. Direct eye exposure can be dangerous.

DANGER: LASER RADIATION !

Avoid direct eye exposure! Laser radiation can cause

eye damage and/or skin damage. All protective

measures for a safe operation of this laser must be

applied.

This product is a so-called show laser, emitting radiation with a wavelength spectrum

between 400 and 700 nm and producing lighting effects for shows.

Laser Light is different from any other light source with which you may be familiar. The

light from this product can potentially cause eye injury if not set up and used properly.

Laser light is thousands of times more concentrated than light from any other kind of light

source. This concentration of light power can cause instant eye injuries, primarily by

burning the retina (the light sensitive portion at the back of the eye). Even if you cannot

feel “heat” from a laser beam, it can still potentially injure or blind you or your audience.

Even very small amounts of laser light are

potentially hazardous even at long

distances.

Never look into the laser aperture or laser

beams

Never direct the laser beam to people or

animals and never leave this device running

unattended.

This laser may only be used for shows. The

operation of a class 3B show laser is only allowed if the operation is controlled by a

skilled and well-trained operator.

ENGLISH USER MANUAL

JB SYSTEMS®4/36 µ-LASER

Depending on the classification, operating a laser product can produce laser radiation

that may cause permanent eye damage and/or skin damage. The legal instructions for

using a laser product vary from country to country. The user must always inform himself

on the legal instructions valid in his country and apply them to his situation.

The parent document and cornerstone of laser safety standards ANSI Z136.1 (2007)

provides guidance for the safe use of lasers and laser systems by defining control

measures for each of the four laser classes. This valuable document can be obtained

from www.laserinstitute.org

Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect

installations and unskilled operation!

DESCRIPTION:

1. MODE button: Use this button to select one of the 4 modes:

Fast automatic mode (LED is red)

Slow automatic mode (LED is red)

Sound activated (LED is blue)

Sound strobe effect (LED is blue)

Press this button for about 2.5 seconds to turn off the fixture.

2. INTERNAL MICROPHONE: The built-in microphone is used to synchronize the laser

show to the beat of the music. You can set the sensitivity of the microphone via the

wireless remote control.

3. IR RECEIVER: used to control the unit by the wireless remote control.

4. LED INDICATOR: shows you if the laser is in automatic mode (LED is red) or in sound

activated mode (LED is blue).

5. LASER DIMMER: here you can set the intensity of one of the lasers if you would like to

change the balance between the red and the two colors.

6. MAINS INPUT: DC12V input. Connect the supplied mains adapter here.

7. COOLING FAN: used to cool the components inside the enclosure. Make sure to

never cover this fan outlet!

ENGLISH USER MANUAL

JB SYSTEMS®5/36 µ-LASER

8. ON/OFF KEY ACTIVATED SWITCH: used to switch the unit on/off. Use the keys to

make sure only a skilled operator is able to switch the laser on.

9. LASER APERTURE: the laser beam exits the enclosure here; make sure to NEVER

look inside the unit through this opening while the laser effect is switched on!

LASER WARNING LABELS: warn against a potentially dangerous laser when not used

by skilled operators.

“Laser Radiation. Avoid exposure to beam. Class 3R laser product”

“Caution –Class 3B laser. Laser Radiation when open. Avoid exposure to beam.”

OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only.

Improper installation can result in serious injuries and/or damage to property.

Overhead rigging requires extensive experience! Working load limits should be

respected, certified installation materials should be used, the installed device

should be inspected regularly for safety.

Make sure the area below the installation place is free from unwanted persons during

rigging, de-rigging and servicing.

Locate the fixture in a well ventilated spot, far away from any flammable materials and/or

liquids. The fixture must be fixed at least 50cm from surrounding walls.

The device should be installed out of reach of people and outside areas where persons

may walk by or be seated.

Before rigging make sure that the installation area can hold a minimum point load of

10times the device’s weight.

Always use a certified safety cable that can hold 12 times the weight of the device when

installing the unit. This secondary safety attachment should be installed in a way that no

part of the installation can drop more than 20cm if the main attachment fails.

The device should be well fixed; a free-swinging mounting is dangerous and may not be

considered!

Don’t cover any ventilation openings as this may result in overheating.

The operator has to make sure that the safety-relating and machine-technical

installations are approved by an expert before using them for the first time. The

installations should be inspected every year by a skilled person to be sure that safety is

still optimal.

CAUTION EYE DAMAGE: Always position the laser in a way that

prevents the audience from looking directly into the laser beams. The

installation should assure that the beam will not strike the audience.

ENGLISH USER MANUAL

JB SYSTEMS®6/36 µ-LASER

HOW TO CONTROL THE UNIT

Button

function

Description

AUTO

Automatic shows (LED is red)

MUSIC

Sound activated shows (LED is blue)

The LED is flashing when the sound is

detected.

After you have pressed the green music

button, you can select a number from 1 (low)

to 9 (high) to set the sensitivity of the

microphone.

ON/OFF

Used to switch the fixture ON or OFF

COLOR

CHANGING

To change the laser color

PAUSE

Effect pauze

MANUAL

CONTROL

Color 1 Strobing

1 ~ 8 = STROBO from Fast to Slow

9 = ON 0 = OFF

Color 2 Strobing

1 ~ 8 = STROBO from Fast to Slow

9 = ON 0 = OFF

Effect Speed

1 ~ 8 = SPEED from Fast to Slow

0 = OFF

= Effect Rotation DIRECTION

ENGLISH USER MANUAL

JB SYSTEMS®7/36 µ-LASER

MAINTENANCE

Make sure the area below the installation place is free from unwanted persons during

servicing.

Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.

During inspection the following points should be checked:

All screws used for installing the device and any of its parts should be tightly fastened

and may not be corroded.

Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally

free from any deformation.

When an optical lens is visibly damaged due to cracks or deep scratches, it must be

replaced.

The mains cables must be in impeccable condition and should be replaced immediately

when even a small problem is detected.

In order to protect the device from overheat the cooling fans (if any) and ventilation

openings should be cleaned monthly.

The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surroundings can cause

greater accumulation of dirt on the unit’s optics.

Clean with a soft cloth using normal glass cleaning products.

Always dry the parts carefully.

Attention: We strongly recommend internal cleaning to be carried out by qualified

personnel!

SPECIFICATIONS

Mains Input: DC 12V / 600mA

Total Power consumption: 5,7W

Sound Control: Internal microphone

Laser Power:

µ-STAR & µ-QUASAR LASER: 40mW Green CW laser (λ= 532nm)

100mW Red CW laser (λ= 650nm)

µ-QUANTUM LASER: 80mW Blue CW laser (λ= 450nm)

100mW Red CW laser (λ= 650nm)

µ-PHOTON LASER: 40mW Green CW laser (λ= 532nm)

80mW Blue CW laser (λ= 450nm)

Laser radiation class: 3R

Beam diameter @ aperture: <5mm

Divergence (each beam) <2 mrad

Divergence (total output) <160°

Working temperature: 10°C to 40°C

Laser Safety Standard: EN/IEC 60825-1 Ed2, 2007-03

Size: 117 x 92 x 46 mm

Weight: 0.35kg

Every information is subject to change without prior notice

You can download the latest version of this user manual on our website:

www.beglec.com

FRANCAIS GUIDE D’UTILISATION

JB SYSTEMS®8/36 µ-LASER

GUIDE D’UTILISATION

Nous vous remercions d'avoir acheté ce produit JB Systems®. Pour tirer pleinement profit

de toutes les possibilités et pour votre propre sécurité, lisez ces instructions très

attentivement avant d'utiliser cet appareil.

CARACTÉRISTIQUES

Cet appareil ne produit pas d’interférences radio. Ce produit répond aux exigences des

directives européennes et nationales actuelles. La conformité a été établie et les

déclarations et documents correspondants ont été déposés par le fabricant.

Ce dispositif a été conçu pour produire un effet d'éclairage décoratif et est utilisé dans

les systèmes de jeu de lumière.

Jeu de lumière laser fantastique utilisant deux lasers de couleur différente.

Grâce à une technique de grilles spéciales, les faisceaux sont divisés en plusieurs

faisceaux lasers qui se dirigent dans toutes les directions créant un incroyable effet qui

remplit toute la pièce.

Convient pour les projections sur les murs et plafonds de bars, chambres à coucher,

soirées, etc.

Utilisant la "blanking technology", la couleur des faisceaux laser change de façon

continue.

Plug-and-Play : aucun contrôleur n'est nécessaire !

Une télécommande multifonctions infrarouge peut être utilisée pour contrôler les

fonctions

Peut fonctionner en mode autonome via un microphone intégré ou en mode shows

automatiques.

Tout type d'effet stroboscopique disponible

Support réglable et adaptateur secteur inclus.

Interrupteur Marche/Arrêt actionné par une clef pour plus de sécurité

Conforme aux normes EN/IEC 60825-1 Ed2, 2007-03 concernant la Sécurité Laser

AVANT UTILISATION

Avant d'utiliser cet appareil, vérifiez s'il n'a pas été endommagé durant le transport. En

cas de dommages, n'utilisez pas l'appareil et consultez immédiatement votre revendeur.

Important : Cet appareil est expédié de notre usine en parfait état et bien emballé. Il est

absolument nécessaire que l'utilisateur suive strictement les instructions et les

avertissements de sécurité se trouvant dans ce manuel. Tout dommage dû à une

mauvaise manipulation n'est pas garanti. Le revendeur n'accepte aucune responsabilité

pour tous les défauts et problèmes dus au non respect de ce manuel.

Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez

l'appareil, veillez à joindre ce manuel.

Vérifiez le contenu :

Vérifiez que le carton contient les articles suivants :

µ-LASER

Télécommande IR

2 clefs (pour interrupteur à clé)

Alimentation

Support

Bras de fixation

Guide d'utilisation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de iluminación de JB Systems

JB Systems

JB Systems Radiant Manual de usuario

JB Systems

JB Systems Invader Manual de usuario

JB Systems

JB Systems iMove 7S Manual de usuario

JB Systems

JB Systems SCARAB LASER Manual de usuario

JB Systems

JB Systems World star Color ball Manual de usuario

JB Systems

JB Systems MINI-PAR 12TC Manual de usuario

JB Systems

JB Systems Super Winner HID 150W Manual de usuario

JB Systems

JB Systems Genius-2 LED Manual de usuario

JB Systems

JB Systems Matrix LED Manual de usuario

JB Systems

JB Systems Gobo Flower Manual de usuario

JB Systems

JB Systems LED Marvel Manual de usuario

JB Systems

JB Systems LED Quadra Beam Manual de usuario

JB Systems

JB Systems LED Fire Basket Manual de usuario

JB Systems

JB Systems LED Pyramid Manual de usuario

JB Systems

JB Systems LED Illusion Manual de usuario

JB Systems

JB Systems LED SPOT Manual de usuario

JB Systems

JB Systems Smooth Scan-Blue Manual de usuario

JB Systems

JB Systems Theatre Spot 1000W Manual de usuario

JB Systems

JB Systems Sirius Manual de usuario

JB Systems

JB Systems INFERNO Manual de usuario

JB Systems

JB Systems EZ-SPOT15 WW OUTDOOR Manual de usuario

JB Systems

JB Systems Smooth Scan-3 MK2 Laser Manual de usuario

JB Systems

JB Systems ACCU MINI-PAR 12TC MK2 Manual de usuario

JB Systems

JB Systems APOLLO Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

JB Systems m-Quantium Laser Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas