Jaycar Electronics SL3234 Manual de usuario
SOLAR LED LIGHT WITH PIR
Introduction
The LED light is powered by rechargeable battery. A waterproof solar panel can keep the rechargeable
batteries topped up. Each unit has a built-PIR motion detector, which automatically turns the light on 5
seconds, 20 seconds or flashing 20 seconds. This fully sustained lighting unit is perfect for application
where mains power is unavailable. It is very simple and easy to install.
Please read this manual carefully before commencing installation.
Contents
Solar LED LIGHT WITH PIR x 1
When someone and objects enter the detection area of the
PIR sensor, the light will go off.
Solar panel x 1
It is used to charge the rechargeable batteries for the Solar
LED LIGHT WITH PIR. When the Solar LED LIGHT WITH PIR
is connected to the Solar Panel, its battery will last longer
Tools Required
Large and small flat bladed screwdrivers
Large and small cross-point screwdrivers
Hammer
Please Note: Tools are not included, consult a professional if you need assistance
Installation
Solar LED LIGHT WITH PIR
Step 1: Remove and retain the screw from the bottom
of the solar LED light with PIR and lift off the cover.
Step 2: Use a small drill to create four fixing holes
at the mounting points.
Step 3: Hold the base of the solar LED light with PIR
in the chosen position, ensuring that the front of PIR
will face towards the centre of the protected area,
and mark and drill four 5mm fixing holes in the wall.
DO NOT drill holes with the PIR in position –
the resulting dust may damage the unit.
Secure the PIR to the wall using two screws
(25mm countersink) and the wall plugs.
°
Step 4: Place 6V (5 x 1.2V) rechargeable battery pack
inside the battery compartment with the correct polarity.
Step 5: Close the base cover and screw it up
Step 6: circumgyrate function(have 3 parts can circumgyrate)
Step 7: Plug-in the Solar Panel into t solar LED light with PIR
for charging the batteries.
°
180
°
Note :
the Solar Panel’s the best degree 45℃, to get direct sunlight
PIR detects change of luminance and temperature in the environment, it is best to avoid
looking directly at sources of heat such as fires and boilers, and always try to keep away
from a window.
Operation
Powering up the Solar LED light with PIR,LED light on 30 seconds, then LED is off; after 2 minutes
(during this 2 minutes, PIR do not detect and LED off), it goes into working mode.
Note: When time setting set “OFF” place, it is“OFF”mode , nothing work (LED off, PIR sensor do not
work.)
The Solar LED light with PIR use two trim ports setting;1: time setting ,2: Day/night setting
PIR
Two main function operation
The Solar LED light with PIR has two main function:
1.setting knobs(time setting and Day/night setting ),
2.PIR sensor detects ,
Setting knobs operation
setting knobs(time setting and Day/night setting)
Day/night setting :start from to
According to environment light-intensity, the position of day/night setting knob may be set as
below :
Time Setting
Day/Night Setting
·Daytime – The light will switch off
·Night time – the light will switch on if a person or object enters the detection range.
·If some other light source brightens the surrounding during the night the sensor will
detect this as daytime. In this case the sensor will not detect anything. Please set the
Lighting control to
·Daytime and night time – The light will switch on
·Unrelated to the brightness during day and night, the light will always light up if
anything enters the detection range
Time setting has 4 parts: 5S; 20S; Flashing(5S/20S);OFF
time setting Day/
night
setting
Environment Light-Intensity
the Strongest
light-intensity
the stronger
light-intensity
the strong
light-intensity
the low
light-intensity
the lowest
light-intensity
1: 5S
LED light 5S LED light 5S LED light 5S LED light 5S LED light 5S
off LED light 5S LED light 5S LED light 5S LED light 5S
off Off
LED light 5S LED light 5S LED light 5S
off off off LED light 5S LED light 5S
off off off off LED light 5S
2: 20S
LED light
20SLED light
20SLED light
20SLED light
20SLED light
20S
off LED light
20SLED light
20SLED light
20SLED light
20S
off off LED light
20SLED light
20SLED light
20S
off off off LED light
20SLED light
20S
off off off off LED light
20S
3: Flashing
LED flash
20s
LED flash
20s
LED flash
20s
LED flash
20s
LED flash
20s
off
LED flash
20s
LED flash
20s
LED flash
20s
LED flash
20s
off off
LED flash
20s
LED flash
20s
LED flash
20s
off off off LED flash
20s
LED flash
20s
off off off off
LED flash
20s
4: OFF
All do not work, LED is off
Note: If had setting knobs, after 3 seconds then PIR sensor can work; but having PIR trigger, also
setting knobs
Maintenance
1). Test all detectors once every 3 months
2). The rechargeable battery pack needs to be charged at least 30 minutes for further operation if the
stored power is used up.
3). Do not use cleaners that contain petroleum products, acetone, or thinners etc. Also do not use
abrasives or chemically treated cleaning cloths, all these can cause damage.
4). Check the main body, fixing screws at least twice a year to make sure the device has not come loose.
Specification
Solar LED LIGHT WITH PIR
Type LED LIGHT WITH PIR
Housing ABS
LED On/off indicator
Detection Range ~6-7m
Power Supply 6v (5 X1.2 AAA) rechargeable battery pack – included.
Solar panel
Type Solar battery
Housing ABS
Power output wire PJ2.5 ф3.0 x 2.5m white
SOLAR LED LIGHT WITH PIR –v1.2
Tabla de contenidos
