Jasic CUT80 (L205) Manual de usuario

Operator Manual

www.jasic.co.uk

Plasma Cut Series

|Plasma Cut 60 (JP-61) |Plasma Cut 80 (JP-81) |

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

Your new product

Thank you for selecng this Jasic Technology, Wilkinson Star product.

This product manual has been designed to ensure that you get the most from your new product. Please

ensure that you are fully conversant with the informaon provided paying parcular aenon to the

safety precauons. The informaon will help protect yourself and others against the potenal hazards

that you may come across.

Please ensure that you carry out daily and periodic maintenance checks to ensure years of reliable and

trouble free operaon.

Wilkinson Star Limited are a leading supplier of equipment in the UK and our products are supported by

our extensive service network. Call your distributor in the unlikely event of a problem occurring. Please

record below the details from your product as these will be required for warranty purposes and to

ensure you get the correct informaon should you require assistance or

spare parts.

Date purchased ________________________________________

From where ________________________________________

Serial Number ________________________________________

(The serial number will normally be located on the equipment data plate on the top or underside of the

machine )

Disclaimer

Whilst every eort has been made to ensure that the informaon contained within this manual is

complete and accurate, no liability can be accepted for any errors or omissions. Please note products are

subject to connual development and may be subject to change without noce.

This manual should not be copied or reproduced without the wrien permission of Wilkinson Star

Limited

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

SAFETY

These general safety norms cover both arc welding machines and plasma cung machines unless

otherwise noted.

The equipment must only be used for the purpose it was designed for. Using it in any other way could

result in damage or injury and in breach of the safety rules.

Only suitably trained and competent persons should use the equipment. Operators should respect the

safety of other persons.

Prevenon against electric shock

The equipment should be installed by a qualied person and in accordance with current standards in

operaon. It is the users responsibility to ensure that the equipment is connected to a suitable power

supply. Consult with your ulity supplier if required

If earth grounding of the work piece is required, ground it directly with a separate cable.

Do not use the equipment with the covers removed.

Do not touch live electrical parts or parts which are

electrically charged.

Turn o all equipment when not in use.

Cables (both primary supply and welding) should be

regularly checked for damage and overheang. Do not use worn, damaged, under sized, or poorly

jointed cables.

Ensure that you wear the correct protecve clothing, gloves, head and eye protecon.

Insulate yourself from work and ground using dry insulang mats or covers big enough to prevent any

physical contact with the work ground.

Never touch the electrode if you are in contact with the work ground, or another electrode from a

dierent machine.

Do not wrap cables over your body.

Ensure that you take addional safety precauons when you are welding in electrically hazardous

condions such as damp environments, wearing wet clothing, and metal structures. Try to avoid

welding in cramped or restricted posions.

Ensure that the equipment is well maintained. Repair or replace damaged or defecve parts

immediately. Carry out any regular maintenance in accordance with the manufacturers instrucons.

Safety against fumes and welding gases

Locate the equipment in a well-venlated posion.

Keep your head out of the fumes. Do not breathe the fumes.

Ensure the welding zone is in a well-venlated area. If this is not possible provision should be made for

suitable fume extracon.

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

If venlaon is poor, wear an approved respirator.

Read and understand the Material Safety Data Sheets (MSDS’s) and the manufacturer’s instrucons for

metals, consumable, coangs, cleaners, and de-greasers.

Do not weld in locaons near any de-greasing, cleaning, or spraying operaons. Be aware that heat and

rays of the arc can react with vapours to form highly toxic and irritang gases.

Do not weld on coated metals, unless the coang is removed from the weld area, the area is well

venlated, and while wearing an air-supplied respirator. The coangs on many metals can give o toxic

fumes if welded.

Prevenon against burns and radiaon

Arc rays from the welding process produce intense, visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin.

Wear an approved welding helmet ed with a proper shade of lter lens to protect your face and eyes

when welding or watching.

Wear approved safety glasses with side shields under your helmet.

Never use broken or faulty welding helmets.

Always ensure there are adequate protecve screens or barriers to protect others from ash, glare and

sparks from the welding area. Ensure that there are adequate warnings that welding or cung is taking

place.

Wear suitable protecve ame resistant clothing.

The sparks and spaer from welding, hot work pieces, and hot equipment can cause res and burns

Welding on closed containers, such as tanks, drums, or pipes, can cause them to explode.

Accidental contact of electrode to metal objects can cause arcs, explosion, overheang, or re.

Check and be sure the area is safe and clear of inammable material before carrying out any welding.

Protecon against noise

Some welding and cung operaons may produce noise.

Wear safety ear protecon to protect your hearing.

Protecon from moving parts

When the machine is in operaon keep away from moving parts such as motors and fans. Moving parts,

such as the fan, may cut ngers and hands and snag garments.

Protecons and coverings may be removed for maintenance and controls only by qualied personnel,

aer rst disconnecng the power supply cable.

Replace the coverings and protecons and close all doors when the intervenon is nished, and before

starng the equipment.

Take care to avoid geng ngers trapped when loading and feeding wire during set up and operaon.

When feeding wire be careful to avoid poinng it at other people or toward your body.

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

Always ensure machine covers and protecve devices are in operaon.

Precauons against re and explosion

Avoid causing res due to sparks and hot waste or molten metal

Ensure that appropriate re safety devices are available near the cung / welding area.

Remove all ammable and combusble materials from the cung / welding zone and surrounding areas

Do not cut/weld fuel and lubricant containers, even if empty.

These must be carefully cleaned before they can be cut/ welded.

Always allow the cut/welded material to cool before touching it or placing it in contact with combusble

or ammable material.

Do not work in atmospheres with high concentraons of combusble fumes, ammable gases and dust.

Always check the work area half an hour aer cung to make sure that no res have begun.

Risks due to magnec elds

The magnec elds created by high currents may aect the operaon of pacemakers or electronically

controlled medical equipment.

Wearers of vital electronic equipment should consult their physician before beginning any arc welding,

cung, gouging or spot welding operaons.

Do not go near welding equipment with any sensive electronic equipment as the magnec elds may

cause damage.

RF Declaraon

Equipment that complies with direcve 2004/108/EC concerning electromagnec compability (EMC)

and the technical requirements of EN60974-10 is designed for use in industrial buildings and not those for

domesc use where electricity is provided via the low voltage public distribuon system. Dicules may

arise in assuring class A electromagnec compability for systems installed in domesc locaons due to

conducted and radiated emissions.

In the case of electromagnec problems, it is the responsibility of the user to resolve the situaon. It may

be necessary to shield the equipment and t suitable lters on the mains supply.

LF Declaraon

Consult the data plate on the equipment for the power supply requirements.

Due to the elevated absorbance of the primary current from the power supply network, high power

systems aect the quality of power provided by the network. Consequently, connecon restricons or

maximum impedance requirements permied by the network at the public network connecon point

must be applied to these systems.

In this case the installer or the user is responsible for ensuring the equipment can be connected,

consulng the electricity provider if necessary.

Materials and their disposal

The equipment is manufactured with materials, which do not contain any toxic or poisonous materials

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

dangerous to the operator.

When the equipment is scrapped, it should be dismantled separang components according to the

type of materials.

Do not dispose of the equipment with normal waste. The European Direcve 2002/96/EC on Waste

Electrical and Electronic Equipment states the electrical equipment that has reached its end of life must

be collected separately and returned to an environmentally compable recycling facility.

Handling of Compressed gas cylinders and regulators

All cylinders and pressure regulators used in welding operaons should be handled with care.

Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

Always secure the cylinder safely

Never deface or alter any cylinder

Funcons and characteriscs of the cung machine

Advanced digital control mode

The Plasma cung machines JP 61/81 MUC intelligent digital control technology, and all its major

funcons are performed using soware controls. The digital control plasma cung machine oers

many improvements in funcon and performance when compared with the tradional type plasma

cung machines.

With PWM technology and high power component IGBTs, it inverts the DC voltage, which is reced

from 50Hz/60Hz input AC voltage, to 30K~50KHz AC high voltage. The voltage is dropped and reced

to output the DC power supply for cung. This inverter technology provides a machine which is smaller

and much less weight than the tradional style machine. The technology provides a high eciency unit

and the switching frequency is outside the audible range.

Good consistency and stable performance

In tradional machines consistency and performance is oen governed by the tolerances of the

components used in manufacture and environmental such as temperature and humidity. In some cases

the same machine brand and type can vary in performance due to tolerance dierences. One of the

characteriscs of digital control is that it is not sensive to the change of these parameters. The

performance of cung machine will not be aected by the change of the parameters of individual

parts. Therefore, the consistency and stability of performance of the digital control cuer is beer than

that of tradional cuer.

Powerful cung performance

These machines provide economical cung of metals using compressed air as the plasma gas source.

The cung speed is 1.8 mes when compared with oxyacetylene cung. The machines can cut steel, s

stainless steel, copper, cast iron and aluminium easily and quickly. The arc is easy to ignite arc and uses

a non HF arc ignion mode. There is a post-ow funcon operates to cool the torch aer cung. The

simple operaon and high cung speed, smooth cung surface make the plasma process and

excellent cung method.

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

Unpacking

Check the packaging for any signs of damage. Carefully remove the machine and retain the packaging

unl the installaon is complete.

Locaon

The machine should be located in a suitable posion and environment. Care should be taken to avoid

moisture, dust, steam, oil or corrosive gases

Place on a secure level surface and ensure that there is adequate clearance around the machine to

ensure natural airow.

Input connecon

Before connecng the machine you should ensure that the correct supply is available. Details of the

machine requirements can be found on the data plate of the machine or in the technical parameters

shown in the manual.

The equipment should be connected by a suitably qualied competent person. Always ensure the

equipment has a proper grounding. Never connect the machine to the mains supply with the panels

removed.

Output connecons

Insert the torch connector into the connecon socket and turn

clockwise unl it is ght taking care not to over ghten. No air

should leak from this connecon

Insert the work return cable into the socket and ghten by

turning clockwise

Check leads and connecons daily before use.

Connect the work clamp to the workpiece

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

Air pressure seng

The machine should be connected to a suitable air supply, 4.5-5 Bar pressure.

The embedded lter reducer is preset prior to leaving the factory, and users should not need to set

it themselves. Please note this adjustment should be carried out by a competent person only.

If for any reason the reducer needs to be adjusted then it needs to be done as follows:

1Switch o the machine.

2Carefully remove the machine cover panel and handle.

3Switch on the machine taking care not to touch any electrical parts.

4Switch on the air purge switch to start the airow through the machine

5Li up the adjusng knob

6Adjust the pressure by rotang the knob in the “+” direcon to increase the air pressure . Turn the

knob in the “-” direcon to reduce the pressure.

7When the correct pressure is set push down the adjusng knob.

8Turn o the machine.

9Replace the panel and handle

Any water which has been collected by the air regulator will be drained by the auto drain of the

regulator. Air supplies should always be clean and dry.

Operaon

1Turn on the power switch of the machine, and the power indicator illuminates.

2Select proper working mode and proper funcon. There are two working modes available on

the machine panel: 2T and 4T. There are two funcons available: normal cung and metal mesh

cung. The electrode and nozzle are more easily to wear out in metal mesh cung.

3Push the torch trigger on the cung torch, the cung machine works.

4Set cung current according to the thickness of workpiece.

5Bring the copper nozzle of the cung torch into contact with the workpiece (For models with

pilot arc funcon, keep a distance of about 2mm between the copper nozzle of the torch and the

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

workpiece.), and then push the torch trigger. Aer the arc is ignited and started, raise the cung

torch to the posion about 1mm above the workpiece, and start cung.

Controls

1Digital Ammeter

2Power indicator

3Warning indicator

4Pressure guage

5Current adjustment knob

62T / 4T selector

7Air purge / cut selector

8Torch connector

9Work return connector

10 Arc started signal

11 Arc voltage feedback

12 Air inlet

13 Mains Cable

14 Mains switch

A WILKINSON STAR LIMITED PRODUCT 12-16 ISSUE 1

Panel Indicators

Symbol Funcon

Power indicator. It illuminates when the machine is powered on, and it ashes

aer arc is successfully ignited.

Overheang indicator. It illuminates when the working temperature of the IGBT

is overly high. When lit the machine stops working.

2T indicator: It illuminates when the machine is under 2T status.

4T indicator: It illuminates when the machine is under 4T status.

Gas-check indicator It illuminates when the machine is under gas-check status. When lit,

the machine cannot cut.

Metal mesh cung indicator The machine can cut metal mesh when this indicator illu-

minates.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de Jasic

Jasic

Jasic MIG 200 PFC Manual de usuario

Jasic

Jasic Arc 200 PFC Manual de usuario

Jasic

Jasic ARC 160GS Manual de usuario

Jasic

Jasic TIG200PACDC PFC Manual de usuario

Jasic

Jasic JM-160C Manual de usuario

Jasic

Jasic Power Arc 160 PFC Manual de usuario

Jasic

Jasic MIG 270 Separate Manual de usuario

Jasic

Jasic Plasma Cut 100 Manual de usuario

Jasic

Jasic EVO 2.0 Manual de usuario

Jasic

Jasic MIG250P Manual de usuario

Jasic

Jasic TIG Series Manual de usuario

Jasic

Jasic MIG 350 Pulse Separate Manual de usuario

Jasic

Jasic EVOLVE200 PLUS Manual de usuario

Jasic

Jasic 315P AC/DC Digital Manual de usuario

Jasic

Jasic ARC PFC Series Manual de usuario

Jasic

Jasic MIG 270S Manual de usuario

Jasic

Jasic TIG 200 AC/DC Analog Manual de usuario

Jasic

Jasic MIG 250S Manual de usuario

Jasic

Jasic JT-315PMWD Manual de usuario

Jasic

Jasic JT-200A Manual de usuario

Jasic

Jasic Arc 140 Manual de usuario

Jasic

Jasic MIG 350C Manual de usuario

Jasic

Jasic TIG Series Manual de usuario

Jasic

Jasic AC/DC315P Guía de inicio rápido

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario