JAI SW-4010Q-MCL-M52 Manual de usuario

Thank you for purchasing this product.

Be sure to read this documentation before use.

This documentation includes important safety precautions and instructions on how to operate the unit. Be sure to read this documentation to ensure

proper operation.

The contents of this documentation are subject to change without notice for the purpose of improvement.

@2022 JAI

User Manual

Tentative Version

SW-4010Q-MCL-M52

RGB Color & SWIR Prism Line Scan Camera

with Mini Camera Link Interface

Document Version: Tentative

SW-4010Q-MCL-M52_Manual_Ver.Tentative_2022-11-25

SW-4010Q-MCL-M52 User Manual (Tentative) Table of Contents

- 2 -

Table of Contents

Table of Contents 2

About Technical Note 6

Notice/Warranty 7

Notice 7

Warranty 7

Certifications 7

CE Compliance 7

FCC 7

Warning 8

Usage Precautions 9

Notes on Cable Configurations 9

Notes on Attaching the Lens 9

Notes on Camera Link Cable Connections 9

Phenomena Specific to CMOS Image Sensors 10

Phenomena Specific to InGaAs Image Sensors 10

Notes on Exportation 10

Package Contents 11

Features 12

Feature Overview 12

Parts Identification 13

①Lens Mount (M52-Mount) 13

②Digital I/O-1 and Digital I/O-2 Video Output Connectors 13

③POWER/TRIG LED 15

④DC IN/TRIG Connector (12-Pin Round) 15

⑤AUX Connector (10-pin) 17

⑥ ⑦ Mounting Holes 17

Preparation 18

Step 1: Connect Devices 19

①Lens 20

Attach the Lens 20

②Mounting 21

SW-4010Q-MCL-M52 User Manual (Tentative) Table of Contents

- 3 -

③Camera Link Cable 21

④Frame Grabber Board 21

⑤AUX Cable (10 Pin) (Option) 21

⑥DC IN / Trigger IN Connection Cable 21

⑦AC Adapter (Power Supply) 21

Step 2: Verify Camera Operation 22

Step 3: Verify the Connection Between the Camera and PC 23

Step 4: Configure Basic Settings for the Camera 24

Configure the Camera Output Formats 24

Configure the ImageScalingMode Settings 25

Configure Trigger, Exposure, and Line Rate Settings 26

Control via External Triggers 26

Control Without External Triggers 26

Short ASCII Commands for Trigger, Exposure, Line Rate Settings 27

Step 5: Adjust the Image Quality 29

Configure the Line Rate 29

DSNU Correction (Pixel Black Correct) 29

PRNU Correction (Pixel Gain Correct) 31

Adjust the Black Level 33

Adjust the White Balance 34

Step 6: Configure Various Other Settings 34

Step 7: Save the Settings 35

Save the User Settings 35

Load the User Settings 36

Main Functions 37

Basic Function Matrix 37

GPIO (Digital Input/Output Settings) 39

Camera Output Formats 40

Camera Link Bit Assignments 42

Image Scaling Mode (Xscale) 44

SWIRPixelMode and SWIRHalfPixelMode 45

Exposure Mode 46

Trigger Control 47

SW-4010Q-MCL-M52 User Manual (Tentative) Table of Contents

- 4 -

Pixel Sensitivity Correction 48

Defective Pixel Correction 49

Gain Control (RGB Channels) 50

Gain Control (SWIR Channel) 51

Gamma Function 52

To Use the Gamma Function 53

LUT (Lookup Table) 54

To Use the LUT Function 54

LUT Value 55

Shading Correction 56

To Use the Shading Correction Function 57

Black Level Correction 57

Variable Line Rate 58

Electronic Shutter 59

ExposureActive Function 60

Test Pattern Function 60

Color Space Conversion (Color Transformation Control) 61

Counter and Timer Control Function 63

Counter Occurrence Diagram 64

Internal Camera Blocks 64

To Use the Counter Function 65

Chromatic Aberration Correction 66

Connecting Rotary Encoders 67

Noise Reduction Filter Functions 68

Setting List 69

Selector 69

Feature Properties 70

DeviceControl 70

ImageFormatControl 72

AcquisitionControl 74

AnalogControl 76

LUTControl 78

ColorTransformationControl 79

SW-4010Q-MCL-M52 User Manual (Tentative) Table of Contents

- 5 -

DigitalIOControl 80

CounterAndTimerControl 83

EncoderControl 84

UserSetControl 85

TransportLayerControl 86

PulseGenerator 87

ShadingControl 89

CorrectionControl 90

SWIRImageFormatControl 92

SWIRAcquisitionControl 92

SWIRAnalogControl 94

SWIRLUTControl 95

SWIRTransportLayerControl 95

SWIRShadingControl 96

SWIRCorrectionControl 97

SWIRBlemishControl 98

Miscellaneous 99

Troubleshooting 99

Power Supply and Connections 99

Image Display 99

Settings and Operations 99

Specifications 100

Spectral Response 103

Dimensions (SW-4010Q-MCL-M52) 104

Lens Dimensions (JMO-M5231-2828-C4) 105

Comparison of the Decibel Display and Multiplier Display 106

User's Record 107

Revision History 108

SW-4010Q-MCL-M52 User Manual (Tentative) Table of Contents

- 6 -

About Technical Note

Some additional technical information is provided on the JAI website as Technical Notes. In this

manual, if a technical note is available for a particular topic, the above icon is shown. Please refer

to the following URL for Technical notes.

https://www.jai.com/support-software/technical-notes

SW-4010Q-MCL-M52 User Manual (Tentative) Notice/Warranty

- 7 -

Notice/Warranty

Notice

The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan,

and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the

use of its product and assumes no responsibility for any errors which may appear or for damages

resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to

make changes without notice.

Company and product names mentioned in this manual are trademarks or registered trademarks

of their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE Compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC

(Electromagnetic compatibility), JAI Ltd., Japan declares that SW-4010Q-MCL-M52 complies

with the following provisions applying to their standards.

EN61000-6-2

EN61000-6-3

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

lReorient or relocate the receiving antenna.

lIncrease the separation between the equipment and receiver.

lConnect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

lConsult the dealer or an experienced radio/TV technician for help.

SW-4010Q-MCL-M52 User Manual (Tentative) Notice/Warranty

- 8 -

Warning

Changes or modifications to this unit not expressly approved by the party responsible for FCC

compliance could void the user’s authority to operate the equipment.

SW-4010Q-MCL-M52 User Manual (Tentative) Usage Precautions

- 9 -

Usage Precautions

Notes on Cable Configurations

The presence of lighting equipment and television receivers nearby may result in video noise. In

such cases, change the cable configurations or placement.

Notes on Attaching the Lens

How to Clean a Sensor

Avoiding Dust Particles

When attaching the lens to the camera, stray dust and other particles may adhere to the sensor

surface and rear surface of the lens. Be careful of the following when attaching the lens.

lWork in a clean environment.

lDo not remove the caps from the camera and lens until immediately before you attach the

lens.

lTo prevent dust from adhering to surfaces, point the camera and lens downward and do not

allow the lens surface to come into contact with your hands or other objects.

lAlways use a blower brush to remove any dust that adheres.

lNever use your hands or cloth, blow with your mouth, or use other methods to remove dust.

Notes on Camera Link Cable Connections

Secure the locking screws on the connector manually,

and do not use a driver. Do not secure the screws too

tightly. Doing so may wear down the screw threads on the

camera. (Tightening torque: 0.15 N·m or less)

Caution: Secure manually. Do not secure too tightly.

SW-4010Q-MCL-M52 User Manual (Tentative) Usage Precautions

- 10 -

Phenomena Specific to CMOS Image Sensors

The following phenomena are known to occur on cameras equipped with CMOS image sensors.

These do not indicate malfunctions.

lAliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing

(zigzag distortion) may appear on the monitor.

lBlooming: When strong light enters the camera, some pixels on the CMOS image sensor

may receive much more light than they are designed to hold, causing the accumulated

signal charge to overflow into surrounding pixels. This “blooming” phenomenon can be seen

in the image but does not affect the operation of the camera.

lFixed pattern noise: When shooting dark objects in high-temperature conditions, fixed

pattern noise may occur throughout the entire video monitor screen.

lDefective pixels: Defective pixels (white and black pixels) of the CMOS image sensor are

minimized at the factory according to shipping standards. However, as this phenomenon

can be affected by the ambient temperature, camera settings (e.g., high sensitivity and long

exposure), and other factors, be sure to operate within the camera’s specified operating

environment.

Phenomena Specific to InGaAs Image Sensors

The following phenomena are known to occur on cameras equipped with InGaAs linear image

sensors. These do not indicate malfunctions.

lBlooming: When the camera is pointed at scenes containing very bright areas or strong

light sources, some pixels on the InGaAs linear image sensor may accumulate more than

the maximum charge allowed, causing the excess charge to overflow into the surrounding

pixels. While this "blooming" affects image quality, it does not affect the operation of the

camera.

Notes on Exportation

When exporting this product, please follow the export regulations of your country or region.

Tabla de contenidos

Otros manuales de Sistema de visión artificial de JAI

JAI

JAI GO-5000M-PGE-UV Manual de usuario

JAI

JAI GO-5000M-USB-UV Manual de usuario

JAI

JAI GO-5000M-USB-UV Manual de usuario

JAI

JAI GO-5000M-PMCL-UV Manual de usuario

JAI

JAI GO-5000M-PGE-UV Manual de usuario

JAI

JAI GO-5000M-PGE Manual de usuario

JAI

JAI GO-5100MP-USB Manual de usuario

JAI

JAI GO-2400M-PGE Manual de usuario

JAI

JAI BM-500 GE Manual de usuario

JAI

JAI GO-5000M-PGE-1 Manual de usuario

Manuales populares de Sistema de visión artificial de otras marcas

Festo

Festo SBOC-M-R1B-H Manual de usuario

Banner

Banner VE200G1B Manual de usuario

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manual de usuario

Sony

Sony Vision Exchange PEQ-C100 Manual de usuario

Datalogic

Datalogic MX-U81 Instrucciones de instalación

Cognex

Cognex In-Sight D900 Series Manual de usuario

Spektrum

Spektrum SPMVR2520 Manual de usuario

Huaray

Huaray Movidius Series Manual de usuario

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manual de usuario

SVS-Vistek

SVS-Vistek exo174 U3 Series Manual de usuario

Teledyne

Teledyne e2v Eliixa+ Series Manual de usuario

Photron

Photron FASTCAM Mini CX Series Manual de usuario

National Instruments

National Instruments Vision CVS-1455 Manual de usuario

Omron

Omron FH-L550 Manual de usuario

iGen

iGen NV20/20 Manual de usuario

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manual de usuario

Cognex

Cognex In-Sight 9902L Manual de usuario

Feniex

Feniex C-5500 Manual de usuario