Jacto ARBUS 500 Manual de usuario

TECHNICAL NOTICE

1

For more information, consult Technical Assistance

Toll free: 1-800-522-8610

E-mail: [email protected]

Home page: www.jacto.com

Tower Kit is available for Jacto Arbus 500 and Arbus 200 airblast sprayers.

Follow instructions below for assembly:

ARBUS 500 / ARBUS 200

TOWER KIT

CTI - ??/??/2012

IMP-????

1-Locate left and right deflectors on

the rear of the machine (A).

A

2-Loosen mounting bolts (B) and

remove both right and left deflectors.

B

B

ATTENTION!

With sprayer hitched to the tractor, park on a rm and level

ground free of obstacles. Apply the tractor parking brake.

Wash the machine before assembling Tower Kit.

TECHNICAL NOTICE

2

3-Pull the clip and remove the quick

fitting clamp (C). Then, disconnect

the hose from left and right branches.

C

4-Loosen nozzle branch mounting

bolts (D) and remove both right and

left branches. D

D

D

branch

hose

5-Use a screwdriver (E) to loosen

the hose clamp and disconnect the

branch hose.

E

nozzle

branch

branch hose

TECHNICAL NOTICE

3

7-Loosen and remove mounting bolts

for spacer bushings (H).

I

I

guard screens

8-Remove spacer bushings (I) and

guard screens from both left and

right sides.

NOTE:

The spacer bushings (I)

will be replaced by new

ones included with the

Tower Kit. Keep the remo-

ved spacer bushings (I)

and the deflector upper

fastening (G) in an appro-

priate place for future use

without the Tower Kit.

6-To remove the fan guard screen,

loosen the mounting bolt for the

spacer bushing (F) and remove the

deflector upper fastener (G). Next,

tighten the mounting bolt (F) for the

spacer bushing.

G

F

H

TECHNICAL NOTICE

4

9-Equipment without spacer bushin-

gs and guard screen ready for Tower

Kit installation.

1-Connect the branch hose to the

Tower Kit (J) and tighten the clamp

with a screwdriver (L).

JL

Tower Kit

2-Tower Kit with branch hose con-

nected.

> Tower Kit assembly

TECHNICAL NOTICE

5

3-The items shown are included with

the Tower Kit and are used in the

assembly.

4-Remove nozzle holders from left

and right branches.

5-Install the nozzle holders with seal

(1) on the Tower Kit nozzle branch (2

and 3). By, placing the nozzle holder

seal (1) in the hole of the Tower Kit

nozzle branch and install the nozzle-

-holder (3). 1

2

3

Kit Tower

nozzle holder

TECHNICAL NOTICE

6

6-Use the spacer bushings included

in the kit and install on the Tower Kit

as shown in the picture.

7-Install the Tower Kit to the fan hou-

sing. Align the spacer bushings with

the holes on the fan housing.

TECHNICAL NOTICE

7

8-With Tower Kit installed, insert

mounting bolts into spacer bushings

(M) and tighten.

M

9-With both sides of Tower Kit instal-

led, locate the two mounting holes

(N and O). Insert mounting bolts and

tighten.

N

O

TECHNICAL NOTICE

8

10-Connect the branch hose to the

quick fitting (right and left sides) and

attach the quick fitting clamp (P).

P

11-Machine with Tower Kit installed.

Arbus 200

Arbus 500

Este manual sirve para los siguientes modelos

1

Otros manuales de Pistola pulverizadora de pintura de Jacto

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario