J2 240 Manual de usuario
Version 1.0 April 2015
J2 240
User Manual
i
Copyright 2015
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
ii
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical Power Supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket
must be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or
local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire
or electric shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation
iii
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with
the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding
18kg.the material of a FIRE ENCLOSURE, in the thinnest significant
wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass
the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg
and for all STATIONARY EQUIPMENT, the material of a FIRE
ENCLOSURE, in the thinnest significant wall thickness used, shall
be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
iv
Revision History
Revision Date Description
V1.0 April, 2015 Release
v
Table of Contents
1 Item Checklist................................................1
1-1Standard Items............................................................................... 1
1-2Optional Items ................................................................................ 2
2 System View...................................................3
2-1Front View & Rear View.................................................................. 3
2-2Side View ........................................................................................ 4
2-3Bottom View.................................................................................... 4
2-4Dimension & View Angle................................................................ 5
2-5I/O View........................................................................................... 7
3 System Assembly & Disassembly.................8
3-1Install the Power Adapter...............................................................8
3-2Replace the HDD............................................................................ 9
3-3Replace the SSD Card.................................................................... 9
4 Peripherals Installation.............................. 10
4-1Install the MSR Module ...............................................................10
4-2Install the iButton Module ...........................................................11
4-3Install the Addimat Key Reader...................................................12
4-4Install the Customer Display (Graphic LCM)...............................13
4-5Install the 2nd Display...................................................................14
4-5-1How to activate the 2nd display Under Windows................................15
4-6Install the Wall Mount Kit ............................................................18
4-7Install the Cash Drawer................................................................21
5 Specification ............................................... 23
6 Configuration .............................................. 25
6-1D36 Motherboard Layout ............................................................25
6-2Connectors & Functions ..............................................................26
6-3Jumper Settings ...........................................................................27
Appendix: Driver Installation......................... 30
1
1 Item Checklist
1-1 Standard Items
a. System b. Power adapter (65W)
c. Power cable d. RJ45-DB9 cable (x4)
e. Manual CD
2
1-2 Optional Items
a. MSR module b. iButton module
c. Addimat reader d. Customer display ( Graphic LCM )
e. 2nd display f. Wall Mount kit
3
2 System View
2-1 Front View & Rear View
Number Description
1 LED indicator
2 Touch screen
3 Thumb screw for the cable cover
4 Ventilation hole
5 HDD door
6 VFD/2nd display dummy cover
7 MSR/iButton/Addimat key module dummy cover
8 Swing arm base
4
2-2 Side View
2-3 Bottom View
Number Description
1 Rubber foot
2 Power adapter (with holder bracket)
3 IO ports
Fold down the swing arm base
Tabla de contenidos
Manuales populares de Terminal de pago de otras marcas
Ingenico
Ingenico iWL250B Manual de usuario
Optimum
Optimum M4230 Manual de usuario
Triton
Triton RL5000 Manual de usuario
Ingenico group
Ingenico group Lane/8000 Manual de usuario
Gilbarco
Gilbarco FlexPay IV CRIND Manual de instalación y operación
Infinite Peripherals
Infinite Peripherals Infinea Tab Lite Manual de usuario
